Other Settings You Can Make - Pioneer DVR-320-S Operating Instructions Manual

Getting started
7 Select the TV screen type, 'Standard (4:3)' or
'Wide (16:9)'.
Initial Setup
Clock Set TV Screen Size
Basic
Input Line System
Tuner
On Screen Display
Video In/Out
Front Panel Display
Audio In
Power Save
Audio Out
Remote Control SetSetup Navigator
Language
Recording Setup Navigator
Playback
Use the (cursor up/down) buttons to select, then
press ENTER.
8 Is your TV compatible with progressive scan
video?
Initial Setup
Progressive
Basic Clock Set
Tuner Input Line System
Video In/Out On Screen Display
Audio In Front Panel Display
Audio Out Power Save
Language Remote Control SetSetup Navigator
Recording Setup Navigator
Playback
Use the (cursor up/down) buttons to select
Compatible, Not Compatible, or Don't Know, then
press ENTER.
• Note that progressive scan video is only output
through the component video outputs and only when
the video source is NTSC (see page 14).
9 Is this recorder connected to an AV amplifier/
receiver for digital audio?
Initial Setup
Basic Clock Set AV Amp Digital Connect
Tuner Input Line System
Video In/Out On Screen Display
Front Panel Display
Audio In
Power Save
Audio Out
Remote Control Set
Language
Recording Setup Navigator Setup Navigator
Playback
Use the (cursor up/down) buttons to select
Connected, or Not Connected, then press ENTER.
• If you select Not Connected, that completes the
setup. Press ENTER to exit the Setup Navigator, or
select Go Back if you want to go back and start again.
• Select the digital audio formats your AV amplifier/
receiver is compatible with.
Initial Setup
AV Amp Compatibility
Basic Clock Set
Tuner Input Line System
Video In/Out On Screen Display
Audio In Front Panel Display
Audio Out Power Save
Language Remote Control Set
Recording
Setup Navigator Setup Navigator
Playback
Wide (16:9)
Standard (4:3)
Compatible
Not Compatible
Don't Know
Connected
Not Connected
Dolby Digital
Dolby Digital, DTS
PCM only
Use the (cursor up/down) buttons to select Dolby
Digital, Dolby Digital, DTS or PCM only, then press
ENTER.
• Check the operating instructions that came with your
AV amplifier/receiver if you're not sure what it's
compatible with.
10 Is your AV amplifier/receiver compatible with 96
kHz PCM digital audio?
Initial Setup
96kHz PCM Compatible
Basic Clock Set
Tuner Input Line System
Video In/Out On Screen Display
Audio In Front Panel Display
Audio Out Power Save
Language Remote Control Set
Recording Setup Navigator Setup Navigator
Playback
Use the (cursor up/down) buttons to select
Compatible, Not Compatible, or Don't Know, then
press ENTER.
• Check the operating instructions that came with your
AV amplifier/receiver if you're not sure.
11 Press ENTER to exit the Setup Navigator, or select
'Go Back' if you want to start again.
Initial Setup
Basic Clock Set
Tuner Input Line System
Setup is complete!
Video In/Out On Screen Display
Enjoy using your DVD recorder!
Audio In Front Panel Display
Audio Out Power Save
Language Remote Control Set
Recording Setup Navigator Setup Navigator
Playback
That completes basic setup using the Setup Navigator.

Other settings you can make

After setting up using the Setup Navigator, you should be
ready to start enjoying your DVD recorder. It's possible,
however, that you may want to make a couple of
additional settings, depending on how the recorder is set
up for TV broadcasts.
• Manual channel setting – This setting lets you skip
channels where there is no station, as well as
manually tune to stations. See Manual CH Setting on
page 76.
• G-Code channel setting – This setting lets you assign
guide channels to ensure that the G-Code
programming system works correctly. See G-Code
CH Setting on page 77.
• Setting up the remote to control your TV – You can set
up the supplied remote control to control many
brands of TV. See Setting up the remote to control your
TV on page 87.
Compatible
Not Compatible
Don't Know
Finish Setup
Go Back
04
25
En