Cisco ios xr system monitoring command reference (433 pages)
Summary of Contents for Cisco XR 12000 Series
Page 1
Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide Cisco IOS XR Release 4.3.0 Revised December 2012 Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices.
Page 2
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.
Page 7
Installing and Removing a SPA Interface Processor C H A P T E R Handling SIPs Removing and Installing a SIP Guidelines for SIP Removal and Installation Removing a SIP Installing a SIP Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
Page 8
C H A P T E R Troubleshooting the SIP Using debug Commands Packing a SIP for Shipment Packing a SPA for Shipment L O S S A R Y Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide viii OL-17438-04...
This document describes the shared port adapters (SPAs) and SPA Interface Processors (SIPs) that are supported on Cisco XR 12000 Series Routers. This document also describes how to install the supported SIPs and SPAs and how to troubleshoot the installation.
SIPs and SPAs. Related Documentation This section refers you to other documentation that also might be useful as you configure your Cisco XR 12000 Series Router. The documentation listed below is available online. Cisco IOS XR Getting Started Guide •...
Cisco XR 12000 SIP-601 Overview, page 1-14 • SIP and SPA Compatibility Table 1-1 shows the SPAs that are supported on the Cisco XR 12000 Series Router and the SIPs that support them: Table 1-1 SIP and SPA Compatibility on the Cisco XR 12000 Series Router...
1-Port 10-Gigabit Ethernet WAN PHY Router Hardware Installation For Cisco XR 12000 Series Router hardware installation and configuration information, refer to the installation and configuration guide for your router. The guide includes information on the router switch fabric and how it affects the operation of SIPs, as well as SIP slot locations, slot width, and other requirements.
Cisco XR 12000 SIP-600, and the Cisco XR 12000 SIP-601 are supported on the Cisco 124xx and 128xx routers. To support the requirements of this line card, the Cisco XR 12000 Series Router must have at least one Note clock and scheduler card (CSC) installed.
SIP Software and Hardware Compatibility For software configuration information, refer to the Cisco IOS XR software configuration and command reference publications for the installed Cisco IOS XR release. Also refer to the Cisco IOS XR software release notes for additional information.
SPA, in the format slot/subslot/port. Subslots and ports are numbered starting from 0, so each Cisco XR 12000 SIP-600 has two subslots 0 (left) and 1 (right). For example, the interface address of a 1-port SPA located in the second SIP subslot, where the SIP is inserted into router line card slot 3 is 3/1/0.
Table 1-8 Cisco XR 12000 SIP-401 LED LED Label Color State Meaning Status Yellow IOS is loaded and SIP is ready to be enabled. Green SIP is active. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
The Cisco XR 12000 SIP-401 accepts 4 single-width, single-height SPAs. Figure 1-7 shows a Cisco XR 12000 SIP-401 with 4 SPAs installed. The top leftmost SPA slot is subslot 0; the top rightmost SPA slot is subslot 1; the bottom leftmost SPA slot is subslot 2; the bottom rightmost SPA slot is subslot 3.
SPA, in the format slot/subslot/port. Subslots and ports are numbered starting from 0, so each Cisco XR 12000 SIP-401 has four subslots. A 4-port SPA would have ports 0 to 3. For example, the interface address of the second port on a 4-port SPA located in the first SIP subslot, where the SIP is inserted into router line card slot 6 is 6/0/1.
Figure 1-11 shows a Cisco XR 12000 SIP-501 with 2 SPAs installed. The left SPA slot is subslot 0 and the right SPA slot is subslot 1. If one dual-width SPA is installed, it is recognized as being in subslot 0.
SPA, in the format slot/subslot/port. Subslots and ports are numbered starting from 0, so each Cisco XR 12000 SIP-601 has two subslots 0 (left) and 1 (right). For example, the interface address of a 1-port SPA located in the second SIP subslot, where the SIP is inserted into router line card slot 3 is 3/1/0.
The Cisco XR 12000 SIP-601 supports 4 single-height SPAs (the aggregate throughput should not exceed 2 full-rate SPAs); 2 double-height SPAs; 1 dual-width, double-height SPA, or a combination of single-height and double-height SPAs. The Cisco XR 12000 SIP-601 face plate has one Status LED. Figure 1-14 shows the Cisco XR 12000 SIP-601 face plate with 4 single-width, single-height SPAs.
–4 to 149°F (–20 to 65°C) SPA Subslot Numbering on the Cisco XR 12000 SIP-601 The Cisco XR 12000 SIP-601 accepts 4 single-height SPAs (the aggregate throughput should not exceed 2 full-rate SPAs); 2 double-height SPAs; 1 dual-width, double-height SPA, or a combination of single-height and double-height SPAs.
SPA, in the format slot/subslot/port. Subslots and ports are numbered starting from 0, so each Cisco XR 12000 SIP-601 has two subslots 0 (left) and 1 (right). For example, the interface address of a 1-port SPA located in the second SIP subslot, where the SIP is inserted into router line card slot 3 is 3/1/0.
Page 29
Table 1-17 Slot and Port Locations for the 1-Port 10-Gigabit Ethernet SPA Call Out Number Description Slot 3 Subslot 0, Port 3/0/0 Subslot 1, Ports 3/1/0 to 3/1/9 Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 1-17 OL-17438-04...
C H A P T E R Overview: Cisco XR 12000 Series Router Shared Port Adapters This chapter describes the shared port adapters (SPAs) that are supported on the Cisco XR 12000 Series Router and contains the following sections: •...
1-Port 10-Gigabit Ethernet WAN PHY SPA Overview, page 2-84 • SPA Summary Table 2-1 shows the summary descriptions of the SPAs that are supported on the Cisco XR 12000 Series Router. Table 2-1 Supported SPAs on Cisco XR 12000 Series Routers...
(SIP-600 or SIP-601). The bandwidth through the engine and the fabric is no more than 5G for the SIP-501 and is no more than 2.5G for the SIP-401. In Cisco IOS XR software release 3.9.1 or prior, the full-rate SPAs need to be positioned in bay 0 and 1. Note...
Page 34
1-Port 10-Gigabit Ethernet DWDM SPA 10 Gbps 10 Gbps 1-Port 10-Gigabit Ethernet WAN PHY SPA 10 Gbps 10 Gbps 1. Total bandwidth value assumes eight OC-12/STM-4 optics modules. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
Port is enabled by software, and loopback is on. STATUS SPA power is off. Green SPA is ready and operational. Amber SPA power is on and good, and the SPA is being configured. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) • Note The Cisco cable part numbers are 72-4124-01 (with male BNC end) and 72-4131-01 (with female BNC end). Figure 2-1 shows the connectors on the 4-Port Clear Channel T3/E3 SPA, and...
The framer processes incoming and outgoing T3 frames (cbit, m13/m23, and unframe) and E3 (g751, g832) frames. The framer operates at T3/E3 line rates (44.2 44.736/34.368 Mbps) depending on the mode in which it is configured. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
CAB-T3E3-RF-BNC-F (T3 or E3 Cable, 1.0/2.3 RF to BNC-Female, 10 feet) • CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) The Cisco cable part numbers are 72-4124-01 (with Male BNC end) and 72-4131-01 (with Female BNC Note end).
RJ-45 connectors. You can use all ports simultaneously. Each E1 connection supports interfaces that meet G.703 standards. The RJ-45 connection does not require an external transceiver. The E1 ports are E1 interfaces that use 120-ohm shielded twisted pair (STP) cables. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
10/100BASE-T interfaces compliant with appropriate standards. Cisco Systems does not supply Category 5 unshielded twisted-pair (UTP) RJ-45 cables; these cables are available commercially. Figure 2-6 shows the RJ-45 connector. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-11 OL-17438-04...
Page 42
Straight-Through Cable Pinout, RJ-45 Connection to a Hub or Repeater Hub or LAN switch Ethernet port 3 TxD+ 3 RxD+ 6 TxD– 6 RxD– 1 RxD+ 1 TxD+ 2 RxD– 2 TxD– Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-12 OL-17438-04...
Green Port is enabled by software and the link is up. Amber Port is enabled by software and the link is down. STATUS SPA power is off. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-13 OL-17438-04...
Multi-mode short reach (SR) XFP module—XFP-10G-MM-SR • Cisco Systems qualifies the optics that are approved for use with its SPAs. As of Cisco IOS XR Release 3.4.1, the above-listed small form-factor pluggable (XFPs) are the only optical transceiver modules qualified for use.
Page 45
10G-MM-SR: –40 to 185 degrees F (–40 to 85 degrees C) TX power 10GLR SR-1: –8.2 to 0.5 dBm 10GER IR-2: –4.7 to 4 dBm 10GZR LR-2: 0 to 4 dBm 10G-MM-SR: 3dBm,-1.5dBm,-1dBm Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-15 OL-17438-04...
2-Port Gigabit Ethernet SPA LEDs The 2-Port Gigabit Ethernet SPA has two types of LEDs: an A/L LED for each port and a STATUS LED, as shown in Figure 2-12. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-16 OL-17438-04...
Contains a Class 1 laser of 850 nm for (1000BASE-SX) 1000BASE-SX (short wavelength) applications. SFP-GE-L Long wavelength/long haul Contains a Class 1 laser of 1310 nm for (1000BASE-LX/LH) 1000BASE-LX/LH (long wavelength) applications. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-18 OL-17438-04...
Page 49
IEEE 802.3z 1000BASE-LX standard. However, their higher optical quality allows them to reach 6.2 miles (10 km) over single-mode fiber (SMF) versus the 3.1 miles (5 km) specified in the standard. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-19...
Fiber Type (micron) (MHz/km) Cable Distance SFP-GE-S 62.5 722 ft (220 m) 62.5 984 ft (300 m) 50.0 1640 ft (500 m) 50.0 1804 ft (550 m) Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-20 OL-17438-04...
The 5-Port Gigabit Ethernet SPA has two types of LEDs: an A/L LED for each individual port and a STATUS LED for the SPA, as shown in Figure 2-14. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-21 OL-17438-04...
The SFP module has a receiver port (RX) and a transmitter port (TX) that compose one optical interface. Table 2-20 Table 2-21 provide SFP module information and specifications. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-22 OL-17438-04...
Page 53
IEEE 802.3z 1000BASE-LX standard. However, their higher optical quality allows them to reach 6.2 miles (10 km) over single-mode fiber (SMF) versus the 3.1 miles (5 km) specified in the standard. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-23...
Fiber Type (micron) (MHz/km) Cable Distance SFP-GE-S 62.5 722 ft (220 m) 62.5 984 ft (300 m) 50.0 1640 ft (500 m) 50.0 1804 ft (550 m) Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-24 OL-17438-04...
The small form-factor pluggable (SFP) module is an input/output (I/O) device that plugs into the Gigabit Ethernet optical slots on the 10-Port Gigabit Ethernet SPA, linking the port with a 1000BASE-X fiber-optic network. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-26 OL-17438-04...
Page 57
The 1000BASE-SX (short-wavelength) module operates on standard multimode fiber-optic link spans of up to 500 m on 50/125um multimode fiber (MMF) and 300 m on 62.5/125um MMF. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-27 OL-17438-04...
722 ft (220 m) 62.5 984 ft (300 m) 50.0 1640 ft (500 m) 50.0 1804 ft (550 m) SFP-GE-L 1300 9/10 — 6.2 miles (10 km) Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-28 OL-17438-04...
The 1-Port Channelized STM-1/OC-3 SPA has two types of LEDs: an A/L LED for each port and a STATUS LED, as shown in Figure 2-16. Figure 2-16 1-Port Channelized STM-1/OC-3 SPA Faceplate SPA-1XCHSTM1/OC3 C/A (Carrier/Alarm) LED STATUS LED A/L (Active Loopback) LED Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-29 OL-17438-04...
The 1-Port Channelized STM-1/OC-3 SPA supports Frame Relay Fragmentation (FRF.12) and Multilink Note Fame Relay (MFR) features for Cisco IOS XR Software Release 3.6.0 and later releases. 1-Port Channelized STM-1/OC-3 SPA Cables and Connectors The 1-Port Channelized STM-1/OC-3 SPA uses a small form-factor pluggable (SFP) optical transceiver...
Port is enabled by software, loopback is on. STATUS SPA power is off. Green SPA is ready and operational. Amber SPA power is on and good, and SPA is being configured. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-32 OL-17438-04...
SNMP v1 agent (RFC 1155–1157), and Management Information Base (MIB) II (RFC 1213). For Cisco IOS XR Software Release 3.8.0 and beyond, the 1-Port Channelized STM-4/OC-12 SPA Note supports Frame Relay Fragmentation (FRF.12) to achieve fragmentation of data packets and interleaving of voice packets.
1-Port Channelized STM-16/OC-48 SPA LEDs The 1-Port Channelized STM-16/OC-48 SPA has two types of LEDs: an A/L LED for each port and a STATUS LED, as shown in Figure 2-22. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-34 OL-17438-04...
SONET/SDH, and RFC 1662, PPP in HDLC-like Framing. The 1-Port Channelized STM-16/OC-48 SPA also provides support for SNMP v1 agent (RFC 1155–1157), and Management Information Base (MIB) II (RFC 1213). Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-35 OL-17438-04...
Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back to back without using an attenuator between the two of them. Figure 2-24 LC Type Cables Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-36 OL-17438-04...
STATUS LED The WRAP, PASSTHRU, and MATESYNC LEDs apply to the SPA in RPR/SRP mode only. In Note Cisco IOS Release 12.0(31)S, RPR/SRP mode is not supported. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-37 OL-17438-04...
RFC 1155, Structure and Identification of Management Information for TCP/IP-Based Internets • RFC 1156, Management Information Base for Network Management of TCP/IP-Based Internets • RFC 1157, Simple Network Management Protocol (SNMP) • Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-38 OL-17438-04...
(TX), for SONET and SDH connection to the network. In Cisco IOS Release 12.0(31)S, only long-reach (LR) optics are supported. Cisco Systems qualifies the optics that are approved for use with its SPAs. As of Cisco IOS Release 12.0(31)S and Cisco IOS XR Software Release 3.2, the XFP-10GLR-OC192SR and the XFP-10GER-OC192IR are the only optical transceiver modules qualified for use.
Amber Port is enabled by software, and there is at least one alarm (LOS, LOF, RDI, and so on). Blinking SRP mode mismatch alarm is indicated. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-41 OL-17438-04...
Single-mode very-long reach XFP module—XFP-10GZR-OC192LR • Cisco Systems qualifies the optics that are approved for use with its SPAs. As of Cisco IOS XR Software Release 3.4.0, the above-listed XFPs are the only optical transceiver modules qualified for use. Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns (nominal diameter is approximately 10/125 microns) to connect your router to a network.
LC-Type Cable for the XFP Optical Transceiver Modules The 40-pin connector on the 1-Port OC-192/STM-64 POS/RPR XFP SPA is used for resilient packet ring Note (RPR) connections. This feature is not supported in Cisco IOS XR Software Release 3.4.0. OC-192 Module Connections Table 2-32 shows the OC-192 specifications for use with the 1-Port OC-192/STM-64 POS/RPR XFP SPA.
The RPR mate cable is necessary only when the SPA is to be used in RPR mode. It is not needed in POS mode. Support for the RPR feature is dependent on the platform software release feature content. Verify support for the RPR feature support via SPA datasheets or by contacting your Cisco representative. 4-Port OC-3/STM-1 POS SPA Overview The 2-Port and 4-Port OC-3/STM-1 POS SPA is a single-height SPA that installs into one SIP subslot.
Port is enabled by software, and there is at least one alarm. Interface is shut down. Green Port is enabled by software, and loopback is off. Amber Port is enabled by software, and loopback is on. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-45 OL-17438-04...
SONET and SDH single-mode and multimode optical fiber connection (see Figure 2-32). Cisco Systems qualifies the optics that are approved for use with its SPAs. The 2-Port and 4-Port OC-3/STM-1 POS SPA supports the following types of optical transceiver modules: Multimode (MM) SFP module—SFP-OC3-MM •...
Page 77
2-Port and 4-Port OC-3/STM-1 POS SPA-equipped routers back-to-back. Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between them. Figure 2-33 LC-Type Cable Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-47 OL-17438-04...
SONET and SDH single-mode and multimode optical fiber connections (see Figure 2-35). Cisco Systems qualifies the optics that are approved for use with its SPAs. The following OC-3 optical transceiver modules are supported on the 8-Port OC-3 STM-1/OC-12 STM-4 POS SPA: Multimode (MM) SFP module—SFP-OC3-MM •...
Page 81
OC-3-equipped or OC-12-equipped routers back-to-back. Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between them. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-51 OL-17438-04...
SPA, and one STATUS LED. Figure 2-37 shows an example of these LEDs on a 1-Port OC-12/STM-4 POS SPA. Figure 2-37 1-Port OC-12/STM-4 POS SPA Faceplate SPA-1XOC12-POS Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-54 OL-17438-04...
The POS SPA uses a small form-factor pluggable (SFP) optical transceiver module installed in each port for SONET and SDH single-mode and multimode optical fiber connection (see Figure 2-38). Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-55 OL-17438-04...
Page 86
Overview: Cisco XR 12000 Series Router Shared Port Adapters 1-Port OC-12/STM-4 POS SPA Overview Cisco Systems qualifies the optics that are approved for use with its SPAs. The 1-Port OC-12/STM-4 POS SPA supports the following types of optical transceiver modules: •...
The 1-Port OC-48/STM-16 POS SPA is a single-height SPA that is installed in a SIP subslot. The 1-Port OC-48/STM-16 POS SPA provides RPR over SONET (IEEE 802.17), SRP over SONET (Cisco Proprietary), and Packet over SONET (POS) network connectivity with a bandwidth of 9.95 Gbps.
Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP]) and is mapped into the STS-48/STM-64 frame. The 1-Port OC-48/STM-16 POS SPA interface is compliant with the following RFCs: Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-58 OL-17438-04...
This assumes that the chassis is mounted vertically. Figure 2-42 shows the mate cables used to connect the SPAs. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-59 OL-17438-04...
Flashing Port is locally steering. Port is not enabled by software. Green Port is enabled by software, and loopback is off. Amber Port is enabled by software, and loopback is on. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-61 OL-17438-04...
LC-type cable (see Figure 2-44) or two simplex LC-type cables, one for transmit (TX) and one for receive (RX). Figure 2-44 LC-Type Cable Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-62 OL-17438-04...
This assumes that the chassis is mounted vertically. Figure 2-45 shows the mate cables used to connect the SPAs. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-63...
2-Port OC48-POS/RPR SPA Cables, Optical Transceiver Modules, and Connectors, page 2-66 2-Port OC48-POS/RPR SPA LEDs The 2-Port OC48-POS/RPR SPA has five LEDs, as shown in Figure 2-46. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-64 OL-17438-04...
Page 95
Port is enabled by software, loopback is on. STATUS SPA power is off. Green SPA is ready and operational. Amber SPA power is on and good, and SPA is being configured. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-65 OL-17438-04...
Remote User Access over IPSec tunnels. • Any slot of the Cisco XR 12000 Series Router that contains a Cisco XR 12000 SIP-401, Cisco XR 12000 SIP-501, or a Cisco XR 12000 SIP-601 can support up to two Cisco XR12000 IPSec VPN SPAs, or any mixture of the Cisco XR12000 IPSec VPN SPA with other interface SPA types on the same SIP card.
Cisco XR12000 IPSec VPN SPA Overview Note that the Cisco XR12000 IPSec VPN SPA (SPA-IPSEC-2G-2) supported on the Cisco XR 12000 Series Router is a different form factor from the IPSec VPN SPA supported on the Cisco 7600 router (SPA-IPSEC-2G-1).
Port is enabled by software, and there is a valid SONET signal without any alarms. Amber Port is enabled by software, and there is at least one alarm. Port is not enabled by software. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-68 OL-17438-04...
• Multimode—155-Mbps, OC-3 optical fiber (SONET STS-3c or SDH STM-1) Use a multimode optical fiber that has a core/cladding diameter of 62.5/125 microns. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-69 OL-17438-04...
The 1-Port Clear Channel OC-12 ATM SPA has three types of LEDs. There are two LEDs for the port on the SPA, and one STATUS LED, as shown in Figure 2-52. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-70 OL-17438-04...
The 1-Port Clear Channel OC-12 ATM SPA provides one 622.08 Mbps OC-12 network interface for all supported platforms. The single SPA port accepts an SFP module with a duplex LC-type receptacle that allows connection to single-mode or multimode optical fiber. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-71 OL-17438-04...
For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable (see Figure 2-54) or two simplex LC-type cables, one for transmit (TX) and one for receive (RX). Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-72 OL-17438-04...
SPA-2CHT3-CE-ATM TX (Transmit) connector A/L (Active/Loopback) RX (Receive) connector STATUS LED C/A (Carrier/Alarm) LED The 2-Port Channelized T3/E3 ATM CEoP SPA LEDs are described in Table 2-46. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-73 OL-17438-04...
The framer operates at T3 or E3 line rates (44.736 or 34.368 Mbps), depending on the mode in which it is configured. For Cisco IOS XR Software Release 3.7.0, the 2-Port Channelized T3/E3 ATM CEoP SPA supports T3 Note ATM only.
CAB-T3E3-RF-BNC-F (T3 or E3 Cable, 1.0/2.3 RF to BNC-Female, 10 feet) • CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) • The Cisco cable part numbers are 72-4124-01 (with male BNC end) and 72-4131-01 (with female Note • BNC end).
SPA when the cable is installed. 24-Port Channelized T1/E1/J1 ATM CEoP SPA Cables and Connectors The 24-Port Channelized T1/E1/J1 ATM CEoP SPA requires a Cisco cable (part number CABLE-24T1E1J1), which is shown in the following figure.
Line 2 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Line 3 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-77 OL-17438-04...
Page 108
Line 12 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Line 13 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-78 OL-17438-04...
Page 109
Line 22 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Line 23 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-79 OL-17438-04...
To order the patch panel, contact the Sales and Marketing Support staff at SMP Data Communications: 800-880-7674 (toll free in the U.S.A.) • 828-298-2260 (outside the U.S.A.) • ciscoinfo@smpdata.com (email) • Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 2-80 OL-17438-04...
Chapter 2 Overview: Cisco XR 12000 Series Router Shared Port Adapters 1-Port Channelized OC-3 ATM CEoP SPA Overview For product support for the patch panel, contact Cisco Engineering Support at SMP Data Communications: • 800-880-7674 (toll free in the U.S.A.) 828-298-2260 (outside the U.S.A.)
1-Port Channelized OC-3 ATM CEoP SPA Optical Transeiver Modules and Cables Cisco Systems qualifies the optics that are approved for use with its SPAs. The 1-Port Channelized OC-3 ATM CEoP SPA supports the following types of optical transceiver modules: Multimode (MM) SFP module—SFP-OC3-MM •...
Cisco Systems qualifies the optics that are approved for use with its SPAs. As of Cisco IOS Release 12.0(31)S, the above listed XFPs are the only optical transceiver modules qualified for use.Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns (nominal diameter is approximately 10/125 microns) to connect your router to a network.
• Single-mode very-long reach (ZR) XFP module—XFP-10GZR-OC192LR Cisco qualifies the optics that are approved for use with its SPAs. As of Cisco IOS XR Software Release 4.3.0, the above-listed XFP modules are the only optical transceiver modules qualified for use.
Laser/LED Safety, page 3-2 • Safety Warnings Review the safety warnings listed in the Regulatory Compliance and Safety Information for Cisco XR Note 12000 Series Internet Router publication (Document Number 78-4347-xx) that accompanied your router before installing, configuring, or maintaining a line card.
Chapter 3 Preparing to Install a Shared Port Adapter or a SPA Interface Processor Safety Guidelines Cisco equipment operates safely when it is used in accordance with its specifications and product • usage instructions. Electromagnetic Compatibility Regulatory Statements Electromagnetic compatibility regulatory statements are listed in the Regulatory Compliance and Safety Information for XR Cisco 12000 Series Internet Router publication (Document Number 78-4347-xx) that accompanied your router.
Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures. Electromagnetic interference (EMI) shielding is an integral component of the line card. Cisco recommends using an ESD-preventive strap whenever you are handling network equipment or one of its components.
You need the following tools and parts to remove and install SIPs: • Flat-blade or Phillips screwdriver • ESD-preventive wrist or ankle strap and instructions Interface cables to connect the SIP with another router or switch • Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
C H A P T E R Installing and Removing a SPA Interface Processor This chapter describes how to install or remove SIPs on the Cisco XR 12000 Series Router. This chapter contains the following sections: • Handling SIPs, page 4-1 Removing and Installing a SIP, page 4-2 •...
• Installing a SIP • Some of the procedures in the following sections use illustrations of a Cisco 12012 Router to support the Note descriptions of removing and installing SIPs. Although the card cages of Cisco XR 12000 Series Routers differ, the designated use of slots and the process of installing and removing a SIP are basically the same.
Detach the SIP cable-management bracket from the SIP. Step 3 Use a screwdriver to loosen the captive screw at each end of the SIP faceplate. (See Figure 4-2.) Step 4 Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
Page 126
Step 9 dust out of the chassis and to maintain proper airflow through the SIP compartment. Secure the SIP blank to the chassis by tightening its captive screws. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
SIP until the ejector lever hooks are fully latched. (See Figure 4-3.) Figure 4-3 Ejector Levers When inserting a card, make sure that the ejector lever hooks catch the lip of the card cage. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
Install the SPAs and SFP modules in the SPAs that use them. Refer to “Installing and Removing a Shared Port Adapter” section on page 5-1. Install the interface cables. Step 8 Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
C H A P T E R Installing and Removing a Shared Port Adapter This chapter describes how to install or remove SPAs on the Cisco XR 12000 Series Router. This chapter contains the following sections: Handling SPAs, page 5-1 •...
Online Insertion and Removal Online Insertion and Removal Cisco XR 12000 Series Router SIPs and SPAs support online insertion and removal (OIR). SPAs can be inserted or removed independently from the SIP. OIR of a SIP with installed SPAs is also supported.
Inspection, cleaning, and reinspection are critical steps to take before making fiber-optic connections. Cleaning Optical Devices Refer to the Inspection and Cleaning Procedures for Fiber-Optic Connections document for information on cleaning optical devices. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
When the SIP and SPA STATUS LEDs are green, all associated interfaces are configurable. Step 2 Refer to the Cisco IOS XR Getting Started Guide for configuration instructions. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
Finally, you can use the show version command to obtain a few details on the installed SIPs and interfaces available. Using show Commands to Display SPA Information Table 5-1 describes the show commands you can use to display SPA information. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
Page 134
Line status and data link protocol status for a show interfaces pos 2/2/0 slot/subslot/port particular SPA port. Statistics about data traffic sent and received by the port. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
Page 135
If the ENABLED LED on a SPA fails to go on, the SPA or the SIP might not be fully seated even if the SPA lock is in the locked and horizontal position. When a SPA is not recognized, the SIP is deactivated, and its OIR LED is yellow. Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
Page 136
Suspect a faulty SIP. Contact a service representative to report the problem and obtain further – instructions. Step 5 If the SPA is new and is not a replacement, configure the new SPA using Cisco xxxx Series Router SIP and SPA Software Configuration Guide. New interfaces are not available until you configure them. Note...
Chapter 5 Installing and Removing a Shared Port Adapter Checking the Installation To configure the new interface, use Cisco xxxx Series Router SIP and SPA Software Configuration Guide. Using the ping Command to Verify Network Connectivity This section provides brief descriptions of the ping command. The ping command allows you to verify that a SPA port is functioning properly and to check the path between a specific port and connected devices at various locations on the network.
Page 138
Chapter 5 Installing and Removing a Shared Port Adapter Checking the Installation Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide 5-10 OL-17438-04...
(16-slot) or PDU (8-slot). Using debug Commands Along with the other debug commands supported on the Cisco XR 12000 Series Router, you can obtain specific debug information for SPAs on the Cisco XR 12000 Series Router using the debug spa privileged EXEC command.
Two packing cushions • Caution The Cisco Systems original packaging is to be used for the shipment of all SIPs. Failure to properly use Cisco Systems packaging can result in damage or loss of product. Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.
• Carton Caution The Cisco Systems original packaging is to be used for the shipment of all SPAs and cable-management brackets. Failure to properly use Cisco Systems packaging can result in damage or loss of product. Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.
Page 142
Chapter 6 Troubleshooting the Installation Packing a SPA for Shipment Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide OL-17438-04...
Page 143
SIPs and SPAs must have the right FPD version to function properly; an FPD incompatibility will disable all interfaces on the SPA or all SPAs within the SIP. An FPD image package is used to upgrade FPD images. Whenever a Cisco IOS XR image is released FPD image package that supports SPAs, a companion SPA FPD image package is also released for that Cisco IOS XR software release.
Page 144
Glossary Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide GL-6 OL-17438-04...