Measuring At One Listening Position (Single Measure) - Yamaha Aventage RX-A870 Owner's Manual

HDMI HDMI HDMI
1 1 1 2 2 2 3 3 3 4 4 4
5 5 5 6 6 6 7 7 7 V-AUX V-AUX V-AUX V-AUX
AUDIO AUDIO AUDIO
1 1 1 2 2 2 2 3 3 3 4 4 4
AV AV AV
5 5 5 5 1 1 1 6 AUDIO 2 2 2 TUNER TUNER TUNER TUNER
BLUETOOTH BLUETOOTH BLUETOOTH BLUETOOTH NET NET NET NET
USB USB USB USB PHONO PHONO PHONO PHONO
PARTY PARTY PARTY PARTY HDMI OUT HDMI OUT HDMI OUT HDMI OUT
MAIN MAIN MAIN MAIN ZONE 2 ZONE 2 ZONE 2 ZONE 2
SCENE SCENE SCENE SCENE
1 1 2 2 3 3 4 4
MUTE MUTE MUTE
PROGRAM PROGRAM PROGRAM PROGRAM VOLUME VOLUME VOLUME VOLUME
TOP MENU TOP MENU TOP MENU TOP MENU POP-UP/MENU POP-UP/MENU POP-UP/MENU POP-UP/MENU
ON ON ON
SCREEN SCREEN SCREEN OPTION OPTION OPTION
Cursor keys
ENTER ENTER ENTER
ENTER
RETURN
RETURN RETURN RETURN DISPLAY DISPLAY DISPLAY
BAND BAND BAND BAND
MODE MODE MODE
TUNING TUNING TUNING TUNING PRESET PRESET PRESET PRESET
SUR. DECODE SUR. DECODE SUR. DECODE STRAIGHT SUR. DECODE STRAIGHT STRAIGHT STRAIGHT
MOVIE MOVIE MOVIE MUSIC MUSIC MUSIC
ENHANCER ENHANCER PURE DIRECT ENHANCER ENHANCER PURE DIRECT PURE DIRECT PURE DIRECT
INFO INFO INFO SLEEP SLEEP SLEEP
1 1 1 2 2 2 3 3 3 4 4 4
5 5 5 6 6 6 7 7 7 8 8 8
9 9 9 0 0 0 MEMORY MEMORY MEMORY ENT ENT ENT
Measuring at one listening position
(single measure)
Follow the procedure below for measurement. It takes about 3 minutes
to perform the measurement.
1
To start the measurement, use the Cursor keys to select
"Measure" and press ENTER.
The measurement will start in 10 seconds. Press ENTER again to
start the measurement immediately.
X
To cancel the measurement temporarily, press RETURN.
The following screen appears on the TV when the measurement
finishes.
Y
If any error message (such as E-1) or warning message (such as W-1) appears, see
"Error messages" (p.48) or "Warning messages" (p.49).
X
To check the measurement results, select "Result". For details, see "Checking
the measurement results" (p.46).
2
Use the Cursor keys to select "Save/Cancel" and press
ENTER.
3
To save the measurement results, use the Cursor keys
(e/r) to select "SAVE" and press ENTER.
The adjusted speaker settings are applied.
X
To finish the measurement without saving the result, select "CANCEL".
4
Use the Cursor keys (e/r) to select "YES" or "NO" to
enable/disable YPAO Volume and press ENTER.
X
• If YPAO Volume is enabled, the high- and low-frequency levels are
• You can also enable/disable YPAO Volume in "YPAO Volume" (p.102) in the
5
Disconnect the YPAO microphone from the unit.
This completes optimization of the speaker settings.
Caution
• The YPAO microphone is sensitive to heat, so should not be placed anywhere
where it could be exposed to direct sunlight or high temperatures (such as on
top of AV equipment).
44
En
automatically adjusted according to the volume so that you can enjoy natural
sounds even at low volume.
"Option" menu.