Installing Wireless Zones - Honeywell LYNXR Installation And Setup Gude

Ademco lynxr series

Hide thumbs Also See for LYNXR:

Installation and setup manual (72 pages)

Table Of Contents

Table of Contents

*HQHUDO,QIRUPDWLRQ

Zones: The control supports up to 24 wireless zones using 5800 Series transmitters, and up to 16

wireless buttons.

Range: The built-in RF receiver can detect signals from wireless transmitters within a nominal

range of 200 feet.

Transmitters: 5800 Series transmitters have built-in serial numbers that must be entered into the

system using the ✻56 or ✻83 interactive mode, or input to the control via the downloader. 5800

Series transmitters (except the 5800RL and 5827, described separately) do not have DIP switches.

Each transmitter's zone number is programmed into the system in ✻56 mode. Some transmitters,

such as the 5816 and 5817, can support more than one "zone" (referred to as loops or inputs). On the

5816, for example, the wire connection terminal block is loop 1,the reed contact is loop 2. Each loop

must be assigned a different zone number.

7KH DQG 7UDQVPLWWHUV GR QRW KDYH (2/ VXSHUYLVLRQ RI WKHLU ORRS ZLULQJ 7KHUHIRUH IRU

8 /

8/ +RXVHKROG %XUJODU\ LQVWDOODWLRQV WKH ORRS ZLULQJ PD\ QRW H[FHHG IHHW

7KH 5/ 01 01 %' %'9 ( :$7&+ 7(03

6:+6 %56 DQG *%' WUDQVPLWWHUV DUH QRW LQWHQGHG IRU DQ\ 8/ LQVWDOODWLRQV

For button transmitters (RF "keys") such as the 5804 and 5801, you must assign a unique zone

number to each individual button used on the transmitter. Each button on the transmitter also has

a pre-designated loop or input number, which is automatically displayed.

House Identification

If you are using a 5804BD/5804BDV, or 5827 Wireless Keypad with

the system, you must program a House ID Code (01–31) in field

to establish proper communication, and the keypad must be set to

the same ID. House ID 00 disables all wireless keypads. An RF

House ID is not necessary for other 5800 Series transmitters; the

entry should be left at "00" (default) in those cases. The 5827 reports

low battery status as zone "00".

Transmitter Supervision

Except for some transmitters/keypads that may be carried off-

premises (5804, 5804BD, 5804BDV, 5804E, 5804WATCH, and

5827), each transmitter is supervised by a check-in signal that is

sent to the receiver at 70–90 minute intervals. If at least one check-

in is not received from each supervised transmitter within a 12-

hour period, the "missing" transmitter number(s) and "FAULT" will

be displayed. The supervision for a particular transmitter in the

system that may also be carried off the premises (5801, 5802MN)

may be turned off by entering it as a "UR" (unsupervised RF) type,

✻

as described in the

56 Enhanced Zone Programming Mode section.

5800 Series transmitters have built-in tamper protection and will

annunciate as a fault condition if covers are removed.

Transmitter Input Types

Each of the following transmitters has one or more unique factory-assigned input (loop) ID codes.

Each of the inputs requires a programming zone

Transmitters can be entered as one of the following types

input type)

Type

"RF" (Supervised RF)

"UR" (Unsupervised RF)

"BR" (Unsupervised Button RF)