Table of Contents
Advertisement
EN 4
2.
Q522.1HE LA
2.3.1
Side Connections
Smart Card Interface: Data Video - In/Out
17
1
Figure 2-2 Smart-card Connector
1
- 3V3 (1)
2
- Ground power
3
- 12V (1)
2
4
- Ground I
C
5
- IR data
6
- POR (2)
7
- TV Clock (3)
8
- Data in (3)
9
- Data out (3)
10 - 5V (1)
11 - H-sync
12 - V-sync
13 - Gnd CVBS in
14 - SCL (4)
15 - SDA (4)
16 - Reserved
17 - B_Pb in (5)
18 - G_Y in (5)
19 - R_Pr in (5)
20 - FBL in (5)
21 - Gnd CVBS out
22 - CVBS out (6)
23 - Reserved
24 - Reserved
25 - Reserved
26 - Gnd Audio in
27 - Audio R
28 - Audio L
29 - Audio R
30 - Audio L/Mono in
31 - Video CVBS/Yin
32 - C in
1. Pin 1, 3, 10: maximum current limits 1.5A for 3.3V, 1.0A for
5V, and 0.6A for 12V. Total power may not exceed 10W.
2. Pin 6: Bidirectional POR. TV will reset the system card
(active low) when mains is switched "off" to "on". DCM can
reset iTV controller by pulling POR low for 150 ms.
3. Pin 7, 8, 9: SPI bus global (either I2C bus or SPI at any one
time, not simultaneously).
4. Pin 14, 15: I2C bus (either I2C bus or SPI at any one time,
not simultaneously).
5. Pin 17, 18, 19, 20: RGB+FBL applicable only for full field
insertion and not for OSD. For CVI input, only applicable for
1fH.
6. Pin 22: CVBS_terr_out when switching from analog RF to
SCART. Composite video out when switch from DVB-T to
SCART.
Head phone (Output)
Bk - Head phone
Cinch: Video CVBS - In, Audio - In
Rd - Audio R
Wh - Audio L
Ye - Video CVBS
S-Video (Hosiden): Video Y/C - In
1
- Ground Y
2
- Ground C
3
- Video Y
4
- Video C
2009-Dec-04
Technical Specifications, Directions for Use, and Connections
32
16
10000_044_090121.eps
090121
+3.3 V
Gnd
+12 V
Gnd
Data
Signal
Clock Signal
Data
Data
+5 V
Signal
Signal
Gnd
DDC clock
DDC data
Blue in Signal
Green in Signal
Red in Signal
Signal
Gnd
1 V
/ 75 W
PP
Gnd
0.5 V
/ 1 kW
RMS
0.5 V
/ 1 kW
RMS
0.5 V
/ 10 kW
RMS
0.5 V
/ 10 kW
RMS
1 V
/ 75 W
PP
0.7 V
/ 75 W
PP
32 - 600 ohm / 10 mW
0.5 V
/ 10 kohm
RMS
0.5 V
/ 10 kohm
RMS
1 V
/ 75 ohm
PP
Gnd
Gnd
1 V
/ 75 ohm
PP
0.3 V
/ 75 ohm
PP
USB2.0
1
- +5V
2
- Data (-)
3
- Data (+)
k
4
- Ground
H
j
HDMI: Digital Video, Digital Audio - In
H
j
j
k
j
k
j
k
1
- D2+
k
2
- Shield
H
3
- D2-
jk
4
- D1+
jk
5
- Shield
6
- D1-
j
7
- D0+
j
8
- Shield
j
9
- D0-
j
10 - CLK+
H
11 - Shield
j
12 - CLK-
13 - Easylink
14 - n.c.
15 - DDC_SCL
H
16 - DDC_SDA
k
17 - Ground
k
18 - +5V
j
19 - HPD
j
20 - Ground
j
j
Common Interface
68p - See diagram B09A
2.3.2
Rear Connections
Mini Jack: Bathroom speaker (Output)
Bk - Bathroom speaker 8 W / 1 W
RJ48 DATA2 (Xpress Box/Set Top Box- In/Out)
1
- +12V
2
- Gnd
3
- Reserved
4
- Reserved
5
- TXD232
6
- RXD232
7
- IR-OUT/SDA
8
- POR
9
- CVBS_out
ot
10 - Gnd CVBS_out
RJ12 DATA1 (SmartCard XPress Box)
jq
Configure via communication menu
jq
Pins
SP-SPI
jq
1
SP Clock, 5V,
active low
2
SP Data In, 5V,
H
active high
H
j
3
Reserved
j
4
SP Data Out, 5V,
active low
1
2
3
4
10000_022_090121.eps
090121
Figure 2-3 USB (type A)
Gnd
19
1
18
2
10000_017_090121.eps
090428
Figure 2-4 HDMI (type A) connector
Data channel
Gnd
Data channel
Data channel
Gnd
Data channel
Data channel
Gnd
Data channel
Data channel
Gnd
Data channel
CEC
DDC clock
DDC data
Gnd
Hot Plug Detect
Gnd
+12V/1W
Gnd
Signal
Signal
Signal
Signal
Signal
Gnd
SP-Serial XP
SP-I2C
Tx_ 5V,
SCL, 5V,
active low
active low
Rx_5V,
Use pin 7 RJ45
active low
for SDA, 5V
active low
Reserved
Reserved
Not use
Not use
k
jk
jk
H
j
H
j
j
H
j
j
H
j
j
H
j
jk
j
jk
H
j
j
H
jk
o
k
H
k
k
k
H
HM-Link
LED Ctrl
IR in to TV, 5V,
active low
Reserved
Status
Hide quick links:
Advertisement
Table of Contents
