Kenwood TK-D240 Service Manual
  1. Manuals
  2. Brands
  3. Kenwood Manuals
  4. Transceiver
  5. TK-D240
  6. Service manual

Kenwood TK-D240 Service Manual

Vhf digital transceiver
Hide thumbs Also See for TK-D240:
Table of Contents

Advertisement

Quick Links

See also: User Manual
SERVICE MANUAL
B5B-7218-00
12
2015
RA035<Rev.001>
COPYRIGHT © 2015 JVC KENWOOD Corporation
1
Precaution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
2
Specific Service Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
3
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
4
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19
5
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-46
This product complies with the RoHS directive for the European market.
B5B-7218-00
SERVICE MANUAL
VHF DIGITAL TRANSCEIVER
TK-D240, TK-D240(V)
COPYRIGHT © 2015 JVC KENWOOD Corporation

TABLE OF CONTENTS

This product uses Lead Free solder.
No.RA035<Rev.001>
2015/12

Advertisement

Table of Contents
loading

Related Manuals for Kenwood TK-D240

Summary of Contents for Kenwood TK-D240

  • Page 1 B5B-7218-00 TK-D240, TK-D240(V) COPYRIGHT © 2015 JVC KENWOOD Corporation TABLE OF CONTENTS PRECAUTION............... . . 1-5 SPECIFIC SERVICE INSTRUCTIONS .
  • Page 2 Neither is any liability assumed for damages resulting from the use of the information contained herein. JVC KENWOOD Corporation reserves the right to make changes to any products herein at any time for improvement purposes. Firmware Copyrights The title to and ownership of copyrights for firmware embedded in KENWOOD product memories are reserved for JVC KENWOOD Corporation.
  • Page 3 Analog 25 kHz is not included in the models sold in the USA or US territories. Analog measurements accord with TIA 603. Digital measurements accord with EN 300 113. JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation. (No.RA035<Rev.001>)1-3...
  • Page 4 7K50F2D, 7K60FXE, 7K60FXD Specifications shown are typical. Analogue measurements accord with TIA 603, EN 300 086 & 219. Digital measurements accord with EN 300 113. JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation. 1-4 (No.RA035<Rev.001>)
  • Page 5 SECTION 2 SPECIFIC SERVICE INSTRUCTIONS SYSTEM SET-UP Merchandise received Frequency range (MHz) RF power Type TK-D240 K,M,E,E2 136~174 5.0W Choose the type of transceiver TK-D240(V) K A personal computer, programming interface (KPG-22A/22U), Transceiver programming and FPU (programming software) are required for programming.
  • Page 6 The KPG-22U driver runs under Windows XP, Vista, 7, 8 or 8.1. The latest version of the USB driver is available for download from the following URL: http://www.kenwood.com/usb-com/ (This URL may change without notice.) 2.2.3.5 Programming software: KPG-166D (Ver. 2.00 or lat-...
  • Page 7 [Firmware upgrade in Firmware Programing Mode] (4) Press "write" button in the window. When the transceiver (1) Start up the firmware programming software (Updater). starts to receive data, the orange LED turns to green. (2) Set the communications speed (normally, 115200 bps) (5) If writing ends successfully, the green LED turns to red.
  • Page 8 2.3.2.4 Audio Amplifier Circuit The demodulated signal from IC400 is sent to an AF amplifier through IC705, and is routed to an audio power amplifier (INT:IC709, EXT:IC707) where it is amplified and output to the speaker. IC707 AF PA (EXT) IC400 IC705 IC709...
  • Page 9 2.3.4 Frequency Synthesizer Unit 2.3.4.1 Frequency synthesizer The frequency synthesizer consists of the TCXO (X1), VCO, PLL-IC (IC2), and buffer amplifiers. The TCXO generates 16.8MHz. The frequency stability of TCXO is 2ppm within the temperature range of -30°C to +60°C. The fre- quency tuning and modulation of the TCXO are done to apply voltage to pin 1 of the TCXO.
  • Page 10 2.3.5.2 Memory Circuit The Memory circuit consists of the MCU (IC710) and Flash memory (IC700). The Flash memory has a capacity of 4M-bit and stores the channel information, the last channel data, the scan on status, and other parameters. 2.3.5.3 Low Battery Warning The battery voltage is monitored by the MCU (IC710 pin 33: BATT).
  • Page 11 2.3.7 Power Supply There are five 5V power supplies and five 3.3V power supplies: 50M, 50V, 50C, 50R, 50T, 33M, 33MS, 33B, 33R and 33MD. 33MS is always output, but turns off when the power is turned off, to prevent a malfunction of the MCU. 50C is a common 5V.
  • Page 12 2.3.8.2 For Digital Voice Mode If the digital data matches in the MCU, the digital voice payload data will go into the Vocoder in the MCU for conversion to PCM. The PCM data will go to the baseband IC through the SPI input, where it will be converted to analog by the DAC. Analog voice will be filtered and finally sent to the audio amplifier.
  • Page 13 Name Function Name Function 32 1PINDET External MIC detection 77 F_CS O Chip Select for Flash 33 BATT Battery Level Input 78 F_SCLK O Clock for Flash 34 RSSI RSSI Input 79 F_DATAI DATA Input to Flash 35 BUSY BUSY Input 80 F_DATAO O DATA Output for Flash 36 TH_DET1...
  • Page 14 Ref. No. Part Name Description Ref. No. Part Name Description IC705 Baseband system Q707 Transistor Level shift(RXD) IC706 DC amplifier (VOX) Q708 Transistor DC switch (EXT PTT) IC707 AF power amplifier Q709 Transistor Q710 control (EXT) Q710 Transistor Ripple filter IC708 AF amplifier Q711...
  • Page 15 TERMINAL FUNCTION 2.6.1 Main unit (XC1-1162-70) Pin No. Name Function CN600 VOLOUT O Volume output to audio amplifier VOLIN I Volume level input for audio control I Power input after power switch I Connect to pin 3 O Voltage output after passing through the R620 O Connect to pin 5 VOLGND - GND for volume level...
  • Page 16 SECTION 3 DISASSEMBLY Precautions for Disassembly Note: You can remove the Main unit from the chassis without 3.1.1 Removing the Case Assembly from the Chassis removing the solder at the positive terminal. However, in (1) Remove the selector knob <1> and volume knob <2>. this case, you cannot attach the packing (G53-2218-03) (2) Remove the two screws <3>.
  • Page 17 Precautions for Reassembly 3.2.2 Assembling the Battery Release Lever (1) Place the lever <2> onto the stopper <1>. 3.2.1 Attaching the Battery Release Lever to the Case As- (2) Place the thick spring <3> onto the lever. sembly (3) Hook the right and left ends of the thin spring <4> onto the (1) Insert one side of the shaft into the hole at the lever fitting tabs of the stopper, then place the thin spring onto the lever section on the case assembly <1>.
  • Page 18 3.2.4 Mounting the Chassis to the Case Assembly 3.2.6 The Nuts of the Volume Knob and Channel Knob (1) Confirm that the waterproof packing attached to the cir- Note that the shape, color and height of the nuts of the volume cumference of the chassis is securely inserted in the knob and channel knob are different from one another.
  • Page 19 SECTION 4 ADJUSTMENT K,M TYPE Test Equipment Required for Alignment Test Equipment Major Specifications 1. Standard Signal Generator Frequency Range 100 to 520MHz (SSG) Modulation Frequency modulation and external modulation Output -127dBm/0.1μV to greater than -47dBm/1mV 2. Power Meter Input Impedance 50Ω...
  • Page 20 Frequency and Signaling 5 reference level adjustments frequency The transceiver has been adjusted for the frequencies shown in Tuning point RX (MHz) TX (MHz) the following table. When required, readjust them following the 136.05000 136.10000 adjustment procedure to obtain the frequencies you want in ac- tual operation.
  • Page 21 Adjustment Item Description Open Squelch The squelch level at level "5" is adjusted. Low RSSI RSSI display level is adjusted. Both "Low RSSI" and "High RSSI" must High RSSI be adjusted. (The curve data of RSSI level is applied.) Tight Squelch The squelch level at level "9"...
  • Page 22 Order Adjusutment item Adjust item (Analog Wide) (Analog Narrow) (DMR) Number Adjustment range Open Squelch Receive Section 5 1 ~ 1024 Low RSSI Receive Section 6 1 ~ 1024 High RSSI Receive Section 7 1 ~ 1024 Tight Squelch Receive Section 8 1 ~ 1024 Battery Warning Level...
  • Page 23 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 3. Low power 1)Test Channel Power meter Panel Check 0.75W~1.25W check Channel: 1 Ammeter 1.2A or less (Battery volt- Test Signaling Mode: Analog age: 7.5V) Signaling: 1 PTT: Press [Transmit] button.
  • Page 24 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 3. Trans- 1) Adj item: [Transmit Assist] Panel FPU [V] indicator on the PC 2.4~2.6V mit Assist 2) Adj item: [Low], [Low’], [Center], [<][>] window shows VCO [High’], [High] PTT: Press [Trans- lock voltage.
  • Page 25 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 4. Balance 1 1) Adj item: [Balance] Devia- Deviation Panel ANT Panel [FPU] The Deviation of 20Hz 2kHz Tone devia- tion meter meter [<][>] frequency is fixed.
  • Page 26 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 6. Maximum 1) Adj item: [Maximum Devia- Deviation Panel ANT Panel [FPU] 2100Hz 2050~2150Hz deviation tion (Analog Narrow)] meter [<][>] (Analog) Deviation meter Oscillo- Write the same ad- Press [Apply All] LPF : 15kHz...
  • Page 27 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 8. DQT De- 1) Adj item: Deviation Panel ANT Panel [FPU] 0.35kHz 0.35kHz viation [DQT Deviation (Analog Nar- meter [<][>] ±0.05kHz row)] Oscillo- Deviation meter LPF : 3kHz scope HPF : OFF 2) Adj item: [Low], [Low’],...
  • Page 28 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 13. Battery 1) Test Channel Power Panel ANT Check The transceiver warning lev- Channel: 1 meter DVM BATT can transmit with el check Test Signaling Mode: Analog terminal causing the LED Signaling: 1...
  • Page 29 4.6.1 Necessary Deviation adjustment item for each signaling and mode The following shows the necessary adjustment items for each signaling deviation. Please read the following table like the following example. In the case of the signaling “QT (Analog Wide)”, this signaling is composed of three elements [Balance, Maximum Deviation (Analog Wide) and QT Deviation (Analog Wide)].
  • Page 30 Receiver Section Item Condition Measurement Adjustment Specifications /Remarks Test- Unit Terminal Unit Parts Method equipment 1) Test Channel Vol- Turn the Volume knob 1.0V±0.2V AF level Channel: 1 DVM AF VM SP/MIC to obtain 1.0V AF out- setting Test Signaling Mode: Analog Dummy load connec- knob...
  • Page 31 Item Condition Measurement Adjustment Specifications /Remarks Test- Unit Terminal Unit Parts Method equipment 1) Adj item: [Open Squelch [FPU] After input signal from Open (Analog Narrow)] Distortion SP/MIC [<][>] SSG, press [Apply] Squelch 2) Adj item:[Low], [Low’], [Cen- meter connec- button to store the ad- (Analog ter], [High’], [High]...
  • Page 32 E,E2 TYPE Test Equipment Required for Alignment Test Equipment Major Specifications 1. Standard Signal Generator Frequency Range 100 to 520MHz (SSG) Modulation Frequency modulation and external modulation Output -127dBm/0.1μV to greater than -47dBm/1mV 2. Power Meter Input Impedance 50Ω Operation Frequency 100 to 520MHz Measuring Range Vicinity of 10W...
  • Page 33 Frequency and Signaling 5 reference level adjustments frequency The transceiver has been adjusted for the frequencies shown in Tuning point RX (MHz) TX (MHz) the following table. When required, readjust them following the 136.05000 136.10000 adjustment procedure to obtain the frequencies you want in ac- tual operation.
  • Page 34 Adjustment Item Description Open Squelch The squelch level at level "5" is adjusted. Low RSSI RSSI display level is adjusted. Both "Low RSSI" and "High RSSI" must High RSSI be adjusted. (The curve data of RSSI level is applied.) Tight Squelch The squelch level at level "9"...
  • Page 35 Order Adjusutment item Adjust item (Analog Wide 5k) (Analog Wide 4k) (Analog Narrow) (DMR) Number Adjustment range RSSI Reference Receive Section 4 1 ~ 1024 Open Squelch Receive Section 5 1 ~ 1024 Low RSSI Receive Section 6 1 ~ 1024 High RSSI Receive Section 7...
  • Page 36 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 3. Low power 1)Test Channel Power meter Panel Check 0.75W~1.25W check Channel: 1 Ammeter 1.2A or less (Battery volt- Test Signaling Mode: Analog age: 7.5V) Signaling: 1 PTT: Press [Transmit] button.
  • Page 37 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 3. Trans- 1) Adj item: [Transmit Assist] Panel FPU [V] indicator on the PC 2.4~2.6V mit Assist 2) Adj item: [Low], [Low’], [Center], [<][>] window shows VCO [High’], [High] PTT: Press [Trans- lock voltage.
  • Page 38 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 4. Balance 1) Adj item: [Balance] Devia- Deviation Panel ANT Panel [FPU] Make the demodula- tion meter meter [<][>] tion wave into square LPF : 3kHz Oscillo- wave.
  • Page 39 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 6. Maxi- 1) Adj item: [Maximum Devia- Deviation Panel ANT Panel [FPU] 2100Hz 2050~2150Hz mum devi- tion (Analog Narrow)] meter [<][>] ation Deviation meter Oscillo- Write the same ad- Press [Apply All] button...
  • Page 40 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment *2: Refer to the “4.13.1 Necessary Deviation adjustment item for each signaling and mode” table. Regarding Maximum Deviation (Analog), it is common with the adjustment of all analog signalings. 7.
  • Page 41 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 9. Single 1) Adj item: Deviation Panel ANT Panel [FPU] 1.50kHz 1.50kHz Tone Devi- [Single Tone Deviation (Ana- meter [<][>] ±0.05kHz ation log Narrow)] Oscillo- Deviation meter LPF : 15kHz scope...
  • Page 42 Item Condition Measurement Adjustment Specifications /Remarks PC test mode Test- Unit Terminal Unit Parts Method equipment 14. DTMF 1) Adj item: Deviation Panel ANT Panel [FPU] 1.25kHz 1.25kHz Deviation [DTMF Deviation (Analog Nar- meter [<][>] ±0.05kHz row)] Oscillo- Deviation meter LPF : 15kHz scope HPF : OFF 2) Adj item: [Low], [Low’],...
  • Page 43 4.13.1 Necessary Deviation adjustment item for each signaling and mode The following shows the necessary adjustment items for each signaling deviation. Please read the following table like the following example. In the case of the signaling “QT (Analog Wide 5k)”, this signaling is composed of three elements [Balance, Maximum Devi- ation (Analog Wide 5k) and QT Deviation (Analog Wide 5k)].
  • Page 44 4.14 Receiver Section Item Condition Measurement Adjustment Specifications /Remarks Test- Unit Terminal Unit Parts Method equipment 1) Test Channel Vol- Turn the Volume knob 1.0V±0.2V AF level Channel: 1 DVM AF VM SP/MIC to obtain 1.0V AF out- setting Test Signaling Mode: Analog Dummy load connec- knob...
  • Page 45 Item Condition Measurement Adjustment Specifications /Remarks Test- Unit Terminal Unit Parts Method equipment 1) Adj item: [Open Squelch [FPU] After input signal from Open (Analog Wide 4k)] Distortion SP/MIC [<][>] SSG, press [Apply] Squelch 2) Adj item:[Low], [Low’], [Cen- meter connec- button to store the ad- (Analog...
  • Page 46 XC1-1162-70 XCA-001E-00S with the KPG-166D. (Main Unit Number: Note: XC1-1162-71) • When a new printed circuit board is used, the KENWOOD TK-D240 E2 XC1-1162-70 XCA-001E-00S ESN changes, as does the Transceiver Information dis- (Main Unit Number: play of the KPG-166D, but this does not have any effect XC1-1162-71) on the operation of the transceiver.
  • Page 47 SCHEMATIC DIAGRAM MAIN UNIT (XC1-1162-70) PLL SYSTEM 5.0V 0.01u 1000p 0.01u PVDD 18 2 CPVDD 1000p RFINP 17 TEST4 (-71) 1000p 1000p TEST1 RFINN 16 1000p PLL_LE AK1541 VREF2 15 PLL_DATA 0.22u DVSS DATA VREF1 TH_DET PLL_CLK D203,204 0.22u ANT SW BUFFER AMP PRE-DRIVE AMP TX(VHF)
  • Page 48 MEMO (No.RA035<Rev.001>) 2-2...
  • Page 49 PRINTED CIRCUIT BOARD MAIN UNIT (XC1-1162-70) --- Component side view (J7C-0137-00) --- R624 R607 L601 D620 L700 IC600 C611 C615 R759 R752 C612 R768 C756 C745 C604 IC703 C759 R621 C748 D605 C741 R301 C626 R765 C737 C735 R766 CN601 R772 R302 L701...
  • Page 50 MAIN UNIT (XC1-1162-70) --- Foil side view (J7C-0137-00) --- XF400 C428 C501 C279 C842 R403 C425 C508 R751 C504 IC704 R419 C426 R418 R459 R887 C841 L220 S601 C496 C885 R407 R457 IC719 C840 C495 R824 S602 S603 C493 C409 CN912 C435 C492...
  • Page 51 LEVEL DIAGRAM Receiver Section RF (Center Frequency) IF1 (49.95MHz) AF (1kHz) IF2 (450kHz) N: –117dBm 74.8mVrms 76.8mVrms 12.7mVrms 0.63Vrms N: –120dBm (K,M) N: –118dBm (E,E2) N: –106.5dBm N: –102dBm N: –117dBm N: –107dBm 438mVrms 0.76Vrms 76.5mVrms Baseband Baseband IF AMP FM IC IC707 J601...
  • Page 52 BLOCK DIAGRAM MAIN UNIT 1st LOCAL TX/RX TX VCO RX VCO TK-D240-K IC601 XC6209B502P-G TK-D240(V)-K TK-D240-M 50M (5.0V) 136.00~174.00MHz 185.95~223.95MHz 185.95~223.95MHz 136.00~174.00MHz TK-D240-E Q601 EM6M2 IC2 AK1541 TK-D240-E2 TX/RX 50T (5.0V) PLL_DATA PLL_CLK PLL_LE Q602 EM6M2 TX VCO Q6 MCH3914-H/8/ PLL_LD 50R (5.0V)
  • Page 53 PARTS LIST [TK-D240,TK-D240(V)] * SAFETY PRECAUTION Parts identified by the symbol are critical for safety. Replace only with specified part numbers. * BEWARE OF BOGUS PARTS Parts that do not meet specifications may cause trouble in regard to safety and performance.
  • Page 54 Exploded view of general assembly and parts list Block No.M1MM MAIN UNIT<01> 3-2(No.RA035<Rev.001>)
  • Page 55 General assembly Block No. [M][1][M][M]  Symbol No. Part No. Part Name Description Local A0C-0117-00 P.CABINET ASSEMBLY A1A-0029-00 CHASSIS B4D-0034-00 BADGE FRONT B4D-0035-00 BADGE REAR D10-0649-03 LEVER D21-0863-04 SHAFT D32-0441-13 STOPPER E04-0477-15 C.RECEPTACLE-SM E23-1253-24 TERMINAL GROUND E23-1395-04 TERMINAL E37-1288-05 PARALLEL CORD G01-4543-14 COIL SPRING STOPPER...
  • Page 56 Electrical parts list MAIN UNIT  Symbol No. Part No. Part Name Description Local XC1-1162-70 Q715 UMG3N DIGI TR ARRAY Block No. [0][1] Q716 SSM3K324RF BBY56-02V VARI CAP DIODE  Symbol No. Part No. Part Name Description Local BBY56-02V VARI CAP DIODE BBY56-02V VARI CAP DIODE 1SV325F...
  • Page 57  Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local CK73HBB1E103K C CAPACITOR 0.01uF 25V K C285 CC73GCH1H070B C CAPACITOR 7pF 50V B CK73HBB1E103K C CAPACITOR 0.01uF 25V K C290 CK73HBB1E103K C CAPACITOR 0.01uF 25V K CC73HCH1H0R5B C CAPACITOR 0.5pF 50V B...
  • Page 58  Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local C499 CK73HBB1H102K C CAPACITOR 1000pF 50V K C772 CC73HCH1H470J C CAPACITOR 47pF 50V J C500 CK73HBB1A104K C CAPACITOR 0.1uF 10V K C773 CK73HBB1H102K C CAPACITOR 1000pF 50V K C501...
  • Page 59  Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local RK73HB1J683J MG RESISTOR 68kΩ 1/16W J R293 RK73HH1J824D MG RESISTOR 820kΩ 1/16W D RK73HB1J101J MG RESISTOR 100Ω 1/16W J R295 RK73HB1J274J MG RESISTOR 270kΩ...
  • Page 60  Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local R623 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W J R817 RK73HB1J000J MG RESISTOR 0Ω 1/16W J R624 RK73HB1J683J MG RESISTOR 68kΩ 1/16W J R824 RK73HB1J102J MG RESISTOR 1kΩ...
  • Page 61  Symbol No. Part No. Part Name Description Local L222 LR79Z0DD21N9J CHIP INDUCTOR 21.9nH L223 LR79Z0DD27N4J CHIP INDUCTOR 27.4nH L400 L41-1885-53 CHIP INDUCTOR L401 LK73H0AMR10J M.CHIP INDUCTOR 0.1uH L402 LK73G0AQ1R5K M.CHIP INDUCTOR 1.5uH L403 LB73G0BD-005 CHIP FERRITE L404 LR77Z0AER56J CHIP INDUCTOR 0.56uH L405 LK73H0AM27NJ...
  • Page 62 Packing materials and accessories parts list (TK-D240_K,TK-D240_E,TK-D240V_K) Block No.M2MM Packing and accessories Block No. [M][2][M][M]  Symbol No. Part No. Part Name Description Local B0K-0032-00 ------------ PAMPHLET D240_K,D240V_K ------------ PAMPHLET ROHS2 D240_E B5A-0929-00 INST.MANUAL D240_K,D240V_K B5A-0930-00 INST.MANUAL D240_E D32-0456-03 STOPPER H12-4319-05 PACKING FIXTURE ------------...
  • Page 63 Packing materials and accessories parts list (TK-D240_M,TK-D240_E2) Block No.M3MM Packing and accessories Block No. [M][3][M][M]  Symbol No. Part No. Part Name Description Local B0K-0032-00 ------------ PAMPHLET D240_M ------------ PAMPHLET ROHS2 D240_E2 B5A-0931-00 INST.MANUAL D240_M B5A-0930-00 INST.MANUAL D240_E2 D32-0456-03 STOPPER ------------ PROTECTION BAG ------------...
  • Page 64 JVC KENWOOD Corporation Communications Systems Business Unit (No.RA035<Rev.001>) Printed in Japan...

This manual is also suitable for:

Tk-d240(v)Tk-d340Tk-d340u

Table of Contents