Advertisement
<Monitoring 16-bit T or 16-bit C >
RUN
1
T
➀
"ON" is displayed when T or C is ON and "R" is displayed while resetting.
➁
Change over the device to monitor.
T or C that is not used in the program is not displayed.
(A horizontal line "-" is displayed if there is none of T or C in the program.)
➂
When the OK key is pressed once, the current value is changed, and when the OK key is pressed three times, the set value is changed. (Flickers while changing)
➃
Press the "+" key to increase the value. Press the "-" key to decrease the value.
➄
Press the OK key to determine the input. At this time, the input data is written to the PLC.
➅
When the OK key is pressed and held for 2 seconds or more while the current value is changed, the current value is reset to "0" and the contact turns off.
When the OK key is pressed once again, the current value reset operation will be completed.
<Monitoring 32-bit C>
Current value
RUN
1
C
➀
+
RUN
C
S
Set value
<Monitoring 16-bit D>
RUN
1
D
➀
D is scrolled by 1 point at a time.
➁
Select the current value change mode.
➂
Press the "+" key to increase the value. Press the "-" key to decrease the value.
➃
Press the OK key to determine the input. At this time, the input data is written to the PLC.
<Monitoring 32-bit D>
RUN
1
D
➀
D is scrolled by 2 points at a time by the "+" key and by 1 point at a time by the "-" key.
➁
Select the current value change mode.
➂
Press the "+" key to increase the value. Press the "-" key to decrease the value.
➃
Press the OK key to determine the input. At this time, the input data is written to the PLC.
<Error display>
➀
Error step No.
➁
Error code
Press the ESC key or
release the error status to
delete the error display.
➀
➁
This manual confers no industrial
property rights or any rights of any other
kind, nor does it confer any patent
licenses. Mitsubishi Electric Corporation
cannot be held responsible for any
problems involving industrial property
rights which may occur as a result of
using the contents noted in this manual.
➀
<Changing the current value/set value of 16-bit T or 16-bit C>
+
OK
Changing the
current value
-
OK
➂
➁
Changing the
set value
<Changing the current set value of 32-bit C>
D
OK
+
➁
-
➂
-
D
➀
Press the "+" or "-" key to change over the current value and the set value. For the set value, "S" is added in a
right position above the device No.
➁
When the OK key is pressed, the current value or the set value is changed.
➂
Press the "+" key to increase the value. Press the "-" key to decrease the value.
➃
Press the OK key to determine the input. At this time, the input data is written to the PLC.
➄
When the OK key is pressed and held for 2 seconds or more while the current value is changed, the current value
is reset to "0" and the contact turns off.
When the OK key is pressed once again, the current value reset operation will be completed.
<Changing the current value of 16-bit D>
+
OK
➁
-
➀
<Changing the current value of 32-bit D>
D
+
OK
➁
-
➀
<Keyword (Entry code) error
display>
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310 JAPAN
HIMEJI WORKS : 840, CHIYODA CHO, HIMEJI, JAPAN
JY992D84901E
+
OK
➄
Determine
the input.
OK OK
-
<Resetting the current value>
➃
OK
➅
Press and hold it for
2 seconds or more.
OK
➃
Determine
the input.
<Resetting the current value>
OK
OK
➄
➄
Press and hold it for
2 seconds or more.
OK
+
➃
-
➂
+
OK
➃
-
➂
When an keyword (entry code) has been input to the PLC, only the
time can be displayed.
If you press the OK key while the time is displayed, the error message
shown on the left flickers for 5 seconds.
Release the keyword (entry code) in a peripheral unit such as
the FX-10P/20P and the personal computer software for creating
sequence programs.
Manual number : JY992D84901
Manual revision : E
Date
OK
➅
: June 2008
Effective June 2008
Specifications are subject to change without notice
Advertisement
