Wireless-ac/n dual radio access point with poe (136 pages)
Summary of Contents for Cisco WAP125
Page 1
Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with First Published: 2016-10-12 Last Modified: 2017-06-08 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883...
Page 2
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.
Port Settings Table Spanning Tree Protocol VLANs Setting Neighbor Discover LLDP IPv6 Tunnel Time Automatically Acquiring the Time Settings through NTP Manually Configuring the Time Settings Notification LED Display Log Settings Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Page 4
Radio Networks Configuring VAPs Configuring Security Settings Client Filter Configuring a Client Filter List Locally on the WAP device Configuring MAC Authentication on the Radius Server Scheduler Scheduler Profile Configuration Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Page 5
Configuring MAC Traffic Classes QoS Policy QoS Association Guest Access Guest Access Instance Table Guest Group Table Guest User Account Web Portal Customization Monitor C H A P T E R 7 Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Page 6
Packet Capture File Download Using HTTP Support Information Download CPU/RAM Data Where to Go from Here C H A P T E R 1 0 Where to Go from Here Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• If you have multiple IPv6 interfaces on your management station, use the IPv6 global address instead of the IPv6 local address to access the WAP device from your browser. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
2 Locate the IP address of the WAP device. a The WAP device can be accessed and managed by using the Cisco FindIT Network Discovery Utility. This utility enables you to automatically discover all supported Cisco devices in the same local network segment as your computer.
If they are correct, click Submit. Your setup settings are saved and a confirmation window appears. Step 26 Click Finish. The WAP device was configured successfully. You are required to log in again with the new password. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
To change the default password, configure the following: • Old Password — Enter the current password (default is cisco). • New Password — Enter a new password. • Confirm Password — Enter the new password again for confirmation.
• System Time — The current system time. • Firmware Version (Active Image) — The firmware version of the active image. • Firmware MD5 Checksum (Active Image) — The checksum for the active image. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
LED Display, on page 17 Traffic Statistics Traffic Statistics, on page 90 For additional information on the device, you can access the product support page or the Cisco Support Community by: • Click Support to access the product support page.
Adds a new entry to a table or database. Cancel Cancels a change made to the page. Clear All Clears all entries in a log table. Delete Deletes an entry in a table. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Management Buttons Edit Edits an existing entry. Refresh Refreshes the current page with the latest data. Save Saves the settings or configuration. Update Updates the new information to the startup configuration. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
IP address and other network information. Choose one of the following options: ◦DHCP — The WAP device acquires its IP address from a DHCP server on the LAN. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Configuration Options are enabled, Access Point is Auto configured during next reboot considering the information received from DHCP Server for DHCP requests. Configuration upload operation by User/Cisco overrides the Auto Configuration so that the chosen Note configuration file is given preference. In any other cases of rebooting the AP such as firmware upgrade or reboot operations, existing Auto Configuration settings will be effective.
IP address is assigned. This IPv6 address is tentative as it is being verified on the network and cannot be used to transmit or receive traffic. ◦Blank (no value) — No IP address is assigned. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The EEE mode supports QUIET times during low link utilization, allowing both sides of a link to disable portions of each PHY’s operating circuit and save power. Step 2 Click Save. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Spanning Tree Protocol Spanning Tree Protocol In the Spanning Tree Protocol mode, check Enable checkbox to enable the STP mode on the Cisco WAP device. When enabled, STP helps prevent switching loops. STP is recommended if you configure WDS links.
The system administrator can view the Bonjour enabled WAP’s using the latest Internet Explorer plug-in (Cisco FindIT tool). All WAP devices present in a cluster, are shown under the cluster name after the Bonjour discovery process. The administrator should ensure that the name of the cluster is unique within a network.
WAP device is configured to obtain its time from a predefined list of NTP servers. The current system time appears at the top of the page, along with the System Clock Source option. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Time Zone — Select the time zone for your location. • Adjust for Daylight Saving Time — If daylight savings time is applicable to your time zone, check this option and configure the following fields: Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
If the system unexpectedly reboots, the log messages can be useful to diagnose the cause. However, log messages are erased when the system reboots unless you enable persistent logging. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
In the Remote Log Server Table, configure the following parameters: • Server IPv4/IPv6 Address/Name — Enter the IPv4 or IPv6 address, or the host name of the remote log server. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The email alert feature supports mail server configuration, message severity configuration, and up to three email addresses to send urgent and non-urgent email alerts. Use the Email Alert to send messages to the configured email addresses when particular system events occur. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Password — Enter the password for the email account that will be used to send these emails. The password can be from 1 to 64 characters. Step 4 In the Message Configuration area, configure the email addresses and subject line: Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Sep 8 03:48:26 info >> mini_http-ssl[1175]>Max concurrent connections of 20 reached User Accounts One management user is configured on the WAP device by default: • User Name: cisco • Password: cisco Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Step 1 Select System Configuration > User Accounts. The User Account Table shows the currently configured users. The user cisco is preconfigured in the system and has Read/Write privileges. All other users can have Read Only access, but not Read/Write access.
In the Global Settings area, configure the following parameters: • Maximum Sessions — Enter the number of web sessions, including both the HTTP and HTTPS, that can be in use at the same time. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The secure connection does not work until the new certificate is accepted on the browser. In the SSL Certificate File Status area, you can view the current certificate on the WAP device. The following will be displayed: Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The community name acts as a simple authentication feature to restrict the devices on the network that can request data from the SNMP agent. The name functions as a password, and the request is assumed to be authentic if the sender knows the password. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
An SNMP MIB view is a family of view subtrees in the MIB hierarchy. A view subtree is identified by the pairing of an Object Identifier (OID) subtree value with a bit string mask value. Each MIB view is defined Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The SNMPv3 groups allow you to combine users into groups of different authorization and access privileges. Each group is associated with one of three security levels: • noAuthNoPriv • authNoPriv Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Read Views — Choose the read access to MIBs for the group, from one of the following options: ◦view-all — The group is allowed to view and read all MIBs. ◦view-none — The group cannot view or read MIBs. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Encryption Pass Phrase — If you specify DES or AES128 as the encryption type, enter the pass phrase to use to encrypt the SNMP requests. The pass phrase must be between 8 and 32 characters in length. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
RADIUS Server Several features require communication with a RADIUS authentication server. For example, when you configure the Virtual Access Points (VAPs) on the WAP device, you can configure security methods that Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
WAP device as an 802.1X supplicant (client) on the wired network. A user name and password with the MD5 algorithm encryption can be configured to allow the WAP device to authenticate using 802.1X. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
APs are detected, they are shown on the Rogue AP Detection page. If an AP listed as a rogue is legitimate, it can be added to the Known AP List. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The number shown indicates the mode: ◦ 2.4 indicates IEEE 802.11b, 802.11g, or 802.11n mode (or a combination of the modes). ◦ 5 indicates IEEE 802.11a or 802.11n mode (or both modes). Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
You can import a list of known APs from a saved list. The list may be acquired from another AP or created from a text file. If the MAC address of an AP appears in the Trusted AP List, it is not detected as a rogue. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Minimum Password Length — The minimum password character length is a range from 0 to 32. The default is • Password Aging Support — Check to enable password expiration after a configured time period. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Minimum WPA-PSK Length — Enter a key length value. The minimum key length in number of characters is from 8 to 16. The default is 8. Step 4 Click Save. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
In the Basic Settings area, configure these parameters for the selected radio interface: Note Local regulations may prohibit the use of certain radio modes. Not all modes are available in all countries. • Radio — Check Enable to enable the radio interface. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Federal Communications Commission (FCC) or the International Telecommunication Union (ITU-R). • Scheduler — For the radio interface, select the profile from the list. Step 4 In the Advanced Settings area, configure these parameters: Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The additional headers applied to each fragment increase the overhead on the network and can greatly reduce the throughput. • RTS Threshold — The Request to Send (RTS) Threshold value. The valid integer range must be from 0 to 65535. The default is 65535 octets. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Broadcast/Multicast Rate Limiting — Multicast and broadcast rate limiting can improve overall network performance by limiting the number of packets transmitted across the network. By default, this feature is disabled. Until you enable this feature, these fields are disabled: Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• TSPEC Video ACM Limit — The upper limit on the amount of traffic that the WAP device attempts to transmit on the wireless medium using a video AC to gain access. The default limit is 15 percent of total traffic. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Each VAP is associated with a VLAN, and is identified by a VLAN ID (VID). A VID can be any value from 1 to 4094, inclusive. This Cisco WAP device supports nine active VLANs (eight for WLAN plus one management VLAN).
WLAN using the repeated unicast or multicast the frames. • Security — Choose the type of authentication required for access to the VAP. The options are: ◦ None ◦ Static WEP ◦ WPA Personal ◦ WPA Enterprise Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
To delete a VAP, check the VAP and click Delete. To edit a VAP, check the VAP and click Edit. To save your Note changes, click Save when complete. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
WEP key or not. This algorithm is also used in plain text, IEEE 802.1X, and WPA modes. When the authentication algorithm is set to Open System, any client can associate with the WAP device. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
This security mode is backwards-compatible for the wireless clients that support the original WPA. To configure WPA Personal, configure the following: • WPA Versions — Choose the types of client stations from the following: Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
VAP. The default is 86400 seconds and the valid range is from 0 to 86400 seconds. A value of 0 indicates that the broadcast key is not refreshed. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
◦ Capable ◦ Required WiFi Alliance requires PMF to be enabled with default setting of Capable. You may Note disable it when non-compliant wireless clients experience instability or connectivity issues. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The WAP device supports one local Client filter list only. The filter can be configured to grant access only to the MAC addresses on the list, or to deny access only to addresses on the list. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The WAP device supports up to 16 profiles. Only valid rules are added to the profile. Up to 16 rules are grouped together to form a scheduling profile. Periodic time entries belonging to the same profile cannot overlap. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
From the Day of the Week menu, choose the recurring schedule for the rule. You can configure the rule to occur daily, each weekday, each weekend day (Saturday and Sunday), or any single day of the week. Step 5 Set the start and end times: Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The four queues are: • Data 0 (Voice) — High priority queue, with minimum delay. Time-sensitive data such as VoIP and streaming media are automatically sent to this queue. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
WAP device. The Transmission Opportunity (TXOP) is an interval of time, in milliseconds, when a WME client station has the right to initiate transmissions onto the wireless medium (WM) towards the WAP device. The TXOP Limit maximum value is 65535. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Unscheduled Automatic Power Save Delivery (APSD) — Check Enable to enable APSD. The APSD is recommended if VoIP phones access the network through the WAP device. Step 7 Click Save. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The wireless clients can still connect to an WAP device that is operating as a repeater. Before you configure WDS on the WAP device, note these guidelines: • All Cisco WAP devices participating in a WDS link must have the following identical settings: ◦ Radio...
You can verify if the bridge link is up by accessing the Monitor > Dashboard > Wireless page. In the Interface Note Status table, the WDS(x) status should state Up. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
WAP device. WDS is a better solution and is preferred over the Work Group Bridge solution. Use WDS if you are bridging the Cisco WAP150 and Cisco WAP361 devices. If you are not, then consider the Work Group Bridge. When the Work Group Bridge feature is enabled, the VAP configurations are not applied;...
Infrastructure Client Interface. Infrastructure Client Interface. Radio Specifies the Radio Id (Radio 1 (2.4 GHz) or Specifies the Radio Id (Radio 1 (2.4 GHz) or Radio 2 (5GHz)). Radio 2 (5GHz)). Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Specifies if the broadcast of the SSID is Check if you want the downstream SSID to SSID Broadcast available, enabled or disabled. be broadcast. SSID Broadcast is enabled by default. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
If you choose Local or RADIUS, see Client Filter for instructions on creating the Client filter Note list. Step 5 Click Save. The associated downstream clients now have connectivity to the upstream network. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
FBT is enabled per VAP per radio. Before you configure FBT on a VAP, be sure to verify that the VAP is configured with WPA2 security, Note pre-authentication disabled and MFP disabled. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
After configuring the FBT settings, click Save to save the settings. Changing some settings might cause the AP to stop and restart the system processes. If this happens, wireless clients will temporarily lose connectivity. We recommend that you change AP settings when the WLAN traffic is low. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Click Save after copying or deleting a profile. Clicking Export for selected profile/s will export only those profiles. Clicking Export with no profiles Caution selected will Export all the profiles. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
MAC ACLs are Layer 2 ACLs. You can configure the rules to inspect fields of a frame such as the source or destination MAC address, the VLAN ID, or the class of service. When a frame enters the WAP device port, Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
A smaller number means a higher priority. The priority of the new rule will be the lowest of all explicit rules. Note that there is always an implicit rule denying all traffic with lowest priority. • Action — Choose whether to Deny or Permit the action. The default action is Deny. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Destination IPv4 Address — Requires a packet's destination IP address to match the address defined in the appropriate fields. ◦Any — Enter any IP address. ◦Single Address — Enter an IP address to apply this criteria. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
To delete or modify an ACL, select the ACL and then click Delete or Edit To delete or modify a rule, select the rule in the Rule Configuration area and click Delete or Edit. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Source IPv6 Address — Requires the packet's source IP address to match the address defined in the appropriate fields. ◦Any— Allows for any IP address. ◦Single Address — Enter the IP address to apply this criteria. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
◦Custom — Enter the IANA port number to match to the destination port identified in the datagram header. The port range is from 0 to 65535 and includes three different types of ports: ◦0 to 1023 — Well known ports ◦1024 to 49151 — Registered ports Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Action — Choose whether to Deny or Permit the action. The default action is Deny. When you choose Permit, the rule allows all traffic that meets the rule criteria to enter the WAP device. Traffic that does not meet the criteria is dropped. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
◦Custom — Enter an 802.1p user priority to compare against an Ethernet frame. The valid range is from 0 to Step 7 Click OK. The changes are saved to the Startup Configuration. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Source Address — Requires a packet's source IPv4 address to match the IPv4 address defined in the appropriate fields. ◦Any — Any IPv4 address to be used as the source address. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Destination Port — Includes a destination port in the match condition for the rule. The destination port is identified in the datagram header. ◦Any — Any port is allowed as the destination port. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
To add and configure an IPv6 class map: Step 1 Select Client QoS > Traffic Classes. Step 2 Click ✚ to add a Traffic Class. Note The maximum number of class maps is Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The port range is from 0 to 65535 and includes three different types of ports: ◦0 to 1023 — Well-Known Ports ◦1024 to 49151 — Registered Ports ◦49152 to 65535 — Dynamic and/or Private Port Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
To add and configure a MAC class map: Step 1 Select Client QoS > Traffic Classes. Step 2 Click ✚ to add a Traffic Class. Note The maximum number of class maps is Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
◦User Defined — Enter the specific VLAN ID to compare against an Ethernet frame. This field is located in the first/only 802.1Q VLAN tag. The port range is 1 to 4094. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
QoS provided. Select a value from the drop-down list. ◦Remark IP Precedence — Marks all packets for the associated traffic stream with the specified IP precedence value. The IP precedence value is an integer from 0 to 7 Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
When you use a wireless client connect to VAP, and access any URL, the web will hijack the URL to Web Portal Locale page, which you are configure at Access Control/Guest Access page. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Captive Portal. This setting limits the bandwidth used to receive data from the network. The range is from 0 to 300 Mbps. The default is 0. ◦Total Guest User— Total number of guest users. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Web Portal Locale — Select a web portal locale that was created previously from the drop-down list. Step 4 Click Save . Your changes are saved to the Startup Configuration. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Total Guest Users — Displays the number of total guest users. Click the value link on the Total Guest Users to display the Guest User Account page. Step 4 Click Save. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Background Image — Click Browse to choose the image. You can click Upload to upload the images for CP instances. • Logo Image — Click Browse to choose the logo image. You can click Upload to upload the logo images. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
256 characters. • Restore — Deletes the current locale. Step 5 Click Save. Your changes are saved to the Startup Configuration. Step 6 Click Preview to view the updated page. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Clicking Preview will show the text and the images that have already been saved to the Startup Configuration. If you make a change, click Save before clicking Preview to see your changes. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• Red round — No wired connection. • Green round — Wired connection. Click the LAN link to view the LAN Status page. Wireless • Red round — All radios are disabled. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
LAN Status Click on the LAN circle to display the following configuration and status settings on the LAN interface. • MAC Address — The MAC address of the WAP device. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Click Back to return to the Dashboard page. Interface Status The Interface Status table displays the following status information for each Virtual Access Point (VAP) and on each Wireless Distribution System (WDS) interface: Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
You can click Refresh to view the updated information. Note Clients Clients The Clients page displays the client stations associated with the device. Total Number Of Associated Clients—The total number of clients on the WAP device. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Page 97
• Throughput Meter — The last 30 seconds' throughput / Data Rate. You can order the clients through Clients Details, Network (SSID), and so on. Note You can filter clients the through Clients Details, Network (SSID), and so on. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
You can click export to upload the current Authenticated/Failed clients message. Before you click the export button, select the Authenticated client or Failed client to upload, then click Note Export. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
To swap the firmware image running on the WAP device: Step 1 Select Administration > Firmware. The product ID (PID VID) and active and inactive firmware versions are displayed. Step 2 Click Swap Images. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The filename cannot contain the following items: spaces, <, >, |, \, : , (, ), &, ; , #, ? , *, and two or more successive periods. Step 3 Enter the TFTP Server IPv4 address and click Upgrade. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
The filename cannot contain the following characters: spaces, <, >, |, \, : , (, ), &, ; , #, ? , *, and two or more successive periods. Step 5 For a TFTP backup, enter the TFTP IPv4 address. Step 6 Select the configuration file to back up: Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
You can copy files within the WAP device file system. For example, you can copy the Backup Configuration file to the Startup Configuration file type, so that it is used the next time you boot up the WAP device. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• In — Set the reboot time for the reboot to occur after the function is enabled. Note For In, the reboot scheduler is still effective after the device reboots. Step 3 Click Save. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Use the Packet Capture page to configure the parameters of the packet capture, start a local or remote packet capture, view the current packet capture status, and download a packet capture file. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• The capture time reaches the configured duration. • The capture file reaches its maximum size. • The administrator stops the capture. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Click Start Capture to start the capture. To stop the capture, click Stop Capture. Wireshark First, download Wireshark and install it on your computer. You can download Wireshark from https:// www.wireshark.org/. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Page 108
• Exclude beacons and ACK/RTS/CTS frames: !(wlan.fc.type_subtype == 8 | | wlan.fc.type == 1) • Data frames only: wlan.fc.type == 2 • Traffic on a specific BSSID: wlan.bssid == 00:02:bc:00:17:d0 Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Enter the TFTP Server Filename to download if different from the default. By default, the captured packets are stored in the folder file /tmp/apcapture.pcap on the WAP device. Step 4 Click Download. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
• The first line chart update data every 1 seconds. It will show the CPU/RAM activity in 60 seconds. • The second line chart update data every 5 seconds. It will show the CPU/RAM activity in 5 minutes. Step 4 Click Save. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Step 5 Click Download to generate the file based on the current system settings. After a short pause, a window appears to enable you to save the file to your computer. Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Page 112
Troubleshoot Download CPU/RAM Data Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...
Cisco Firmware Downloads http://www.cisco.com/go/smallbizfirmware Select a link to download the firmware for your Cisco product. No login is required. Cisco Open Source Requests If you wish to receive a copy of the source code to which you are...
Page 114
Where to Go from Here Where to Go from Here Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE...