Page 3
ASSEMBLY WARNING There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises.
PRE ASSEMBLY TooLS INCLUDED: T-Wrench (included) UNPACKING L-Wrench (included) Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting PARTS INCLUDED: MODELS this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure.
Page 6
ASSEMBLY STEP 1 (Adventure 7) HARDWARE FoR STEP 1 PART TYPE DESCRIPTIoN BOLT M8X1.25PX60L-30L Adventure 7 shown Cut the yellow banding straps and lift the running deck upward to remove all contents from underneath the running deck. Open HARDWARE FoR STEP 1. Attach LEFT CoNSoLE MAST (1) to MAIN FRAME (2) using 3 BoLTS (A),...
Page 7
ASSEMBLY STEP 2 (Adventure 7) HARDWARE FoR STEP 2 PART TYPE DESCRIPTIoN BOLT M8X1.25PX60L-30L Adventure 7 shown Pull the BASE CABLE (5) away from the treadmill base frame. Connect the CoNSoLE CABLE (5) from the MAIN FRAME (4) to the CoNSoLE CABLE (5) in the bottom of the RIGHT CoNSoLE MAST (6).
Page 8
ASSEMBLY STEP 3 (Adventure 7) HARDWARE FoR STEP 3 PART TYPE DESCRIPTIoN BOLT M6X1.0PX15L Adventure 7 ARC WASHER Φ6.2xΦ18.0x1.5T shown SPRING WASHER Φ6.1xΦ12.2x1.5T Open HARDWARE FoR STEP 3. Slide HANDLEBARS (8) onto CoNSoLE (9). Attach HANDLEBARS (8) to CoNSoLE (9) using 3 BoLTS (B), 3 ARC WASHERS (C) and 3 SPRING WASHERS (D) from each side.
Page 9
ASSEMBLY STEP 4 (Adventure 7) HARDWARE FoR STEP 4 PART TYPE DESCRIPTIoN BOLT M8X1.25PX20L Adventure 7 SPRING WASHER Φ8.2xΦ13.5x2.0T shown FLAT WASHER Φ8.2xΦ15x1.2T ARC WASHER Φ8.2xΦ18.0x1.5T Open HARDWARE FoR STEP 4. Gently place CoNSoLE (9) on top of CoNSoLE MASTS (1&6). Connect the CoNSoLE CABLES (10) and ensure they are tucked inside the CoNSoLE (9).
Page 10
ASSEMBLY STEP 5 (Adventure 7) Lift the RUNNING DECK (11) upward until the FooT LATCH (12) locks. Remove all contents underneath the MAIN FRAME (2&4). Adventure 7 While the RUNNING DECK (11) in the raised shown position, attached the LEFT CoNSoLE MAST CoVER(3) and RIGHT CoNSoLE MAST CoVER(7) to the MAIN FRAME (2&4) using 2 PRE-INSTALLED CoNSoLE MAST CoVER...
Page 11
ASSEMBLY COMPLETE Before the first use, lubricate the treadmill deck by following the instructions in the MAINTENANCE section in the TREADMILL GUIDE. MODELS...