Control Power Supply; Basic Functions - Philips AZ3300 Owner's Manual

English
ACCESSORIES
1 x AC mains lead
1 x Remote Control
TOP AND FRONT PANEL (See 1)
1 PROGRAM
CD: - programs tracks and reviews the program;
Tuner: - programs preset radio stations.
2 CD•FM•MW•LW - selects CD / FM / MW / LW
function
3 IR SENSOR - infrared for remote control
4 TUNER PRESET 4 ,3 - selects a preset radio
station.
5 OPEN•CLOSE - opens / closes CD door.
6 Telescopic antenna - improves FM reception.
+ -
7 VOLUME , - to adjust volume level.
8 DBB (Dynamic Bass Boost) - activates a more vivid
bass response.
9 2; - starts or pauses CD playback.
9 - to stop playback or erase a CD program.
SEARCH ∞ , §
CD: - searches backward and forward within a track;
- skips to the beginning of a current track/
previous/ later track.
Tuner: - (down, up) tunes to radio stations.
0 POWER - power on / off switch
! MODE - selects different play modes: e.g. REPEAT
or SHUFFLE (random) order.
@ Display - shows the status of the set.
BACK PANEL (See 1)
# AC MAINS - inlet for mains lead.
$ Battery compartment - for 6 batteries, type
R-14, UM2 or C-cells.
CONTROL
REMOTE CONTROL (See A)
1 CD – selects CD sound source
2 y – switches the set to standby / on if set
operating on AC power. (Switches set off only if
battery powered)
-
+
3 VOLUME , – adjusts volume level (up, down)
4SHUFFLE – plays all CD tracks in random order
5BASS – selects DBB on/off
62; – starts/ pauses CD playback
7SEARCH 5, 6 – searches backwards/ forwards
within a track
8BAND – selects FM/MW/LW waveband
9PRESET 3, 4 – selects a preset radio station
(up, down)
0TUNING ∞, § – tunes to tuner stations
(down, up)
!TUNER – selects tuner sound source
@9 – stops CD playback;
– erases a CD programme
#¡, ™ – skips to the beginning of a current track
previous/ subsequent track
$MUTE – interrupts/ resumes sound
%REPEAT – repeats a track /programme/ entire CD
CAUTION
Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous radiation
exposure or other unsafe operation.
POWER SUPPLY
Whenever convenient, use the AC power supply to
conserve battery life. Make sure you remove the
power plug from the set and wall socket before
inserting batteries.
Batteries (not included)
• Insert 6 batteries, type R-14, UM-2 or C-cells,
(preferably alkaline) with the correct polarity. (See 6)
• Remote control
Insert 2 batteries, type AAA, R03 or UM4
(preferably alkaline). (See 8)
POWER SUPPLY
IMPORTANT
!
• Incorrect use of batteries can cause electrolyte
leakage and will corrode the compartment or cause
the batteries to burst.
• Do not mix battery types: e.g. alkaline with carbon
zinc. Only use batteries of the same type for the
set.
• When inserting new batteries, do not try to mix old
batteries with the new ones.
• Batteries contain chemical substances, so
they should be disposed of properly.
Using AC Power
1. Check if the AC power supply, as shown on the
type plate located on the bottom of the set,
corresponds to your local power supply. If it does
not, consult your dealer or service centre.
2. Connect the mains lead to the wall socket.
3. To disconnect the mains supply, unplug the set
from the wall socket.
Storing your remote control
This set has a special built-in storage compartment for
your remote control. The storage compartment has a
latch to keep your remote control in place, and is
located inside the CD compartment. (See B)

BASIC FUNCTIONS

Placing your set
To avoid possible staining of
surfaces, please do not stand
this set in vertical position
over a long period.
The type plate is located on the bottom of the
set.
This set complies with the radio interference
requirements of the European Community.
For users in the U.K., please follow the boxed
instructions 'Important notes...' on this sheet.
BASIC FUNCTIONS
Switching on and off and selecting function
1. Press POWER on the set (or y on remote
control) to switch on.
2. Press CD•FM•MW•LW once or more to select :
CD / Tuner function, and operate the respective
function controls.
3. Press POWER to switch off the set.
Note : The DBB setting, tuner presets and the
volume level (maximum to 20) will be retained in the
set's memory.
Adjusting volume and sound (See 2)
-
+
1. Adjust the volume with the VOLUME ,
™ Display shows the volume level in number from
0-32.
2. Press DBB once or more to select dynamic bass
boost on or off.
™ Display: shows when activated.
controls.