Stereo Input Section - Panasonic RAMSA WR-S208 Operating Instructions Manual

STEREO INPUT SECTION
(11 Mic On}Off S'."itch
This switch is used to turn the microphone In-
put circuit on or off. The microphone input signul
IS a monaural signal divided equally between lett
and right of the stereo i npL.t channel.
(2; V1onolStereo Selector Switch
This sw 'tch when pressed, combines the left
and right Inputs 01 the phono and tape/aux sec-
tions into
a
Single monaural signal.
(3] Trim Control
This control is used exclusively for adjusting
microphone input level The control range is
40
dB.
Trim at
0
Trim
Elt
-40
-60 dB -20 dB
(4)
Peak Level Indicator LED
This Indicator is for microphone input level only.
When the level of an input signal reaches
a
value
6 dB below the maximum output level
, the peak
Indicator LED will ligh1.
When this LED Ilg hts. the mic rophone in put
Signal
~18y
be distorted.
(~1 Phona Level Control
This control IS used for phono input level adjust-
men •. . t adJusts the left and right channel levels
simultaneously
(6)
TapelAux Level Control
This control is used to adjust either tape Input
level or auxiliary I n put level . It adjusts the left
and right channel levels Simultaneously.
(7)
Equalizer
High and low 2·band stereo equali zer
Both high and low are a shelving type .
High :
±
1 5 dB I
±
1 2 dB at 10 kHz)(
-C )
Low: ±
1 5 dB I
±
1 5 dB at 100 Hz)(
::>-
I
18)
M onitor Control
Th is control is used to adjust the level sent to
the monitor bus line . Monitor signals are mixed
monaL·ra l signals of Ch ;nnels A and B at pre -
fad er level, used for foldback monitoring .
(9) Effect Control
This control IS used to adjust the level sent to
the effects bus line
E Ifect Signals are mixed monaura I signa,s of
channels A and B at post-fader level, used for
send ing to effects devices .
. 6 -
(101 Pan Control
This control 2 .djusts the b i:: ance of in put signals
between the stereo Sub A and Sub 8 outputs .
Inputs Pan pot Output
pos it ion
Mic
Ce n ter Sub A and Sub B
Counterclock ·
Sub A
wise
ClockWise Sub B
Phono Center Sub A - Phono L
Sub B
. Phono R
Counterclock-
Su b A - Phono L
wisa
Sub B - No OUtput
ClockWise Sub A - No oUlput
Sub B - Phono R
Taps/Aux
Centsr
Sub A . Tape/Aux L
Sub B - Tape /Aux R
C oun tere lock - Sub A - Tape/Aux L
wise
Sub B - No output
ClockWise
Sub A - No output
Sub B - Tape/Aux R
(11) Channel Solo Switch
A
switch for monitoring individual ;nput chan-
nels th rough the headphones PresSing the solo
switch on the WR-S 212 or WR-S21 6 gives that
channel's signal priority over any signal which
might have been select ed on the control room
mor Itor section .
Signals to be monitored
a
ra mixed monau ral
signals of Channels
A
and '1 .
(121 Channel Fader
A 60 mrn carbon fader which Simultaneously
controls Channel A and Channel B. Jsed to ad-
Just : 'le level at whlci:1 stereo Input signals are
sent ,