Directly Accessing A Channel; Confirmation Tone(S) Function; Presetting A Desired Channel - Audiovox SIRIUS SRSIR-001 Owner's Manual

20 on 20
The Techs
Oh Baby Oh Baby
---------------------------------
CH 020 Hits
AUDIO OX
CHANNEL NUMBER
FLASHES
Figure 8. Accessing Channels
SELECTING CHANNEL CATEGORIES (only in Category Mode)
This section describes the procedure used to select a specific group or
category of entertainment, proceed as follows:
1. With the system powered up, momentarily press the Shift (SFT) but-
ton causing the first channel number in the current category to flash for
5 seconds.
2. While the number is flashing, momentarily press and release either direc-
tional button ( ) a desired category is reached. The category will
advance one at a time and will also flash for 5 seconds. If no further
advance is made, the flashing will stop and the category will then remain
steady.
3. To advance rapidly in the chosen direction (Up or Down) and while the
channel number is flashing, momentarily press and release either direc-
tional button ( ) in a rapid manner. Release the directional button
when a desired channel is reached.
NOTE: A low tone busy signal may be heard if the directional buttons are
pressed too quickly indicating that the system has not yet completed the
previous command to advance. Refer to Confirmation Tone(s) Function.
1 2
4 5
20 on 20
The Techs
7 8
Oh Baby Oh Baby
---------------------------------
0
CH 020 Hits
AUDIO OX
SFT
C A T E G O R Y /
C A T E G O R Y /
GROUP NUMBER GROUP
FLASHES
Figure 9. Sellecting Channel Categories
Each category or group is assigned a sequential block of channels. To
navigate within a category, enter Shift (SFT) 0981 Shift (SFT). This
modewill allow the user to switch between channels within a chosen
PRESS KEYPAD BUTTONS
1 2 3
TO SELECT DESIRED
4 5 6
CHANNEL
7 8 9
0
SFT
PRESS THE SHIFT
BUTTON
PRESS DOWN BUTTON TO
3
ADVANCE TO NEXT
6
LOWER CATEGORY
9
PRESS UP BUTTON TO
ADVANCE TO NEXT
PRESS
HIGHER CATEGORY
SHIFT
category, the channel tuning will automatically wrap around from the lastto the
first channel in that category or vice-versa. When a new category is chosen,
the radio will automatically select the first channel in that category.
NOTE: If a directional button is Pressed and Held channels will begin to scroll
in numerical sequence through all categories until the button is released.
This navigation mode will continue to function in the same manner in the new
category. The user must exit this mode before attempting to perform any other
function. To exit this mode, enter Shift (SFT) 0980 Shift (SFT).
PRESETTING DESIRED CHANNELS
This section describes how to preset up to 20 channels on your SCU
(two groups of 10 channels, upper and lower) for rapid and easy access.
Proceed as follows:
1. Select the desired channel you wish to save in memory by using the
directional buttons ( ), direct access method, or category select tuning
method.
2. With the desired channel displayed, press and hold any one of the numbered
keypad buttons for until the confirmation tone (or second tone) is heard
(Refer to Confirmation Tone(s)Function). Continue with this process until
the first group of 10 preset channels is loaded (lower group).
NOTE: There is a preset channel group indicator icon located in the top right
corner of the SCU display. This is used
· ( ) = Lower Preset Channel Group (first 10 channels)
SR1
· ( ) = Upper Preset Channel Group (next 10 channels)
SR2
3. To program the second group of 10 preset channels (upper group) press and
Hold the Shift (SFT) button for 2 seconds until a tone is heard. By doing this
you have entered the second bank (upper group) and the SCU is ready to
accept an additional group of 10 channels into memory.
4. Select the desired channel you wish to save in memory by using the
directional buttons ( ), direct access method, or category select tuning
method.
5. With the desired channel displayed, press and hold any one of the numbered
keypad buttons for until the confirmation tone (or second tone) is heard.
Continue with this process until the second group of 10 preset channels is
loaded (upper group).
Preset channels being previewed are displayed in the lower right corner. A black
number on white background indicates that it is part of the lower group of chan-
nels and a White number on a Black background indicates that it is part of the
upper group.
7
to determine which group you are in.
128-6374
7 of 12