Helpful Hints; Troubleshooting; Error Message; What To Do When - Brother P-TOUCH PT-H110 User Manual

6

HELPFUL HINTS

Troubleshooting

Error message

Message
Battery Low! The batteries are weak.
If using AAA alkaline batteries: Replace them
with six new AAA alkaline batteries. Do not use
old and new batteries together or mix alkaline
batteries with other battery types.
If using Ni-MH batteries: Charge them fully.
Battery Empty! The installed batteries are running low and
need to be changed for continued operation.
Invalid! • There is no text above the cursor when you
selected [Numbering].
• You selected an invalid character for
[Numbering].
• You selected an invalid number for [Label Length].
• You entered an invalid value as the label
length while using templates.
No Text! • You tried to print a text file when there is no
data stored in the memory.
• You pressed
• You pressed
• You pressed
entered while using templates.
2 Line Limit!/
1 Line Limit! • You tried to enter a 3rd line by pressing
• You tried to print or preview two lines of text
while 0.13" (3.5mm) or 0.23" (6 mm) tape is
installed. Install larger tape size.
No Cassette! You tried to print, feed or preview a label when
there is no cassette installed.
Cutter Pressed You pressed the tape cutter lever in the middle
of printing process.
Text Full! You have already entered the maximum
number of characters allowed (80 characters
for text, 50 characters for templates. If your
message contains symbols, the maximum
number of characters could be reduced.).
Text Limit! Since the number of entered characters
Change Length exceeds the label length, reduce the text, or
select [Auto] as the label length.
No Frame OK? • Printing on 0.13" (3.5mm) tape with invalid
Frame setting ON.
(Select
to cancel.)
Feed OK? • Feeding tape after printing when [Chain Print]
is selected. See "Setting Margin".
Insert 0.47" • Only 0.47"(12mm) tape cassette is available
for templates.
Wrong Tape!
• Use a tape cassette with the
Use TZe tape
Cause/Remedy
when no text is entered.
when no text is entered.
or when no text was
to print with no Frame,
mark.

What to do when...

Problem
The display • Check that you installed the batteries
stays blank correctly with the positive and negative ends
after you have in the correct position.
turned on the
• If the batteries are weak, replace them with six
label maker.
new AAA alkaline batteries. Do not use old
and new batteries together or mix alkaline
batteries with other battery types.
• Check that you connected the AD-24ESA
adapter correctly.
When the label
is printed out,
• See "Setting Margin" in this users guide and
there is too
select [Half] or [Narrow] to have smaller
much margin
margins for your label.
(space) on both
sides of the text.
The label maker • Check that you have inserted the tape
does not print, or cassette correctly.
the printed
• If the tape cassette is empty, replace it.
characters are not
• Check that you closed the cassette cover
formed correctly.
correctly.
The label • The batteries may be weak. Replace them
maker's with six new AAA alkaline batteries. Do not
settings have use old and new batteries together or mix
cleared on its alkaline batteries with other battery types.
own.
• When power is disconnected for more than
three minutes, all text and formats in the display
are lost.
.
A blank horizontal • There may be some dust on the print head.
line appears Remove the tape cassette and use a dry
through the cotton swab to gently wipe the print head with
printed label. an up-and-down motion.
The label maker
has "locked up"
(that is, nothing
happens when a • See "Resetting the label maker".
key is pressed,
even though the
label maker is on.)
The power • The batteries may be weak. Replace them
turns off when with six new AAA alkaline batteries. Do not
you try to print. use old and new batteries together or mix
alkaline batteries with other battery types.
• Check that you inserted the batteries correctly.
• A wrong adapter is used; the recommended
adapter is the AD-24ESA.
The tape does
• Check that the end of the tape feeds under
not feed
the tape guides.
correctly or the
tape gets stuck
• The cutter lever is pressed while printing. Do
inside the label
not touch the cutter lever during printing.
maker.
To change
• See "Initial Settings".
language setting.
Solution