Page 1
1115350208 AIR CONDITIONER (SPLIT TYPE) Owner’s Manual Indoor Unit For commercial use Model name: 4-way Cassette type 40TSV0131UP 40TSV0181UP 40TSV0241UP 40TSV0361UP 40TSV0401UP Português English English Owner’s Manual Español 1115350208_EN-TH.indb Cover1 1115350208_EN-TH.indb Cover1 3/29/2559 BE 6:54 PM 3/29/2559 BE 6:54 PM...
– 1 – Original instruction Contents ADOPTION OF NEW REFRIGERANT 1 Precautions for safety ..........3 This Air Conditioner uses R410A an environmentally friendly 2 Part names .
The quali ed installer is a person who installs, maintains, relocates and removes the air conditioners made WARNING installer by Toshiba Carrier Corporation. He or she has been trained to install, maintain, relocate and remove the air WARNING conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such Moving parts.
– 3 – Precautions for safety • Do not place any combustion appliance in a place where it is directly exposed to the wind of air conditioner, otherwise it may cause imperfect combustion. • When the air conditioner is operated with a combustion appliance in the same place, ventilate the room sufficiently. The manufacturer shall not assume any liability for the damage caused by not observing the description of this manual.
Page 5
Information on the transportation, handling and storage of the CAUTION carton To disconnect the appliance from the mains supply. • This appliance must be connected to the mains by means of a switch with a contact separation of at least 3 mm. Examples of indication on the carton The installation fuse (all types can be used) must be used for the power supply line of this air conditioner.
– 5 – Part names Wireless remote controller 3-1. Parts name of remote Temperature button ( Indoor unit ..The set temperature is increased up to controller 30 °C..The set temperature is dropped down to Knob Earth screw 17 °C.
PRESET button FAN speed display Preparation and check before 3-2. Adjusting clock Press this button to change the operation mode to Indicates the selected fan speed. AUTO or one of the preferred operation mode memorized five fan speed levels (LOW , LOW Setting the clock previously.
– 7 – Clock adjusting 3-3. Handling the remote • When you select the timer operation, the remote 3-4. Signal receiving unit controller automatically transmits a signal to the controller The signal receiving unit is attached to the indoor unit. indoor unit at the specified time.
3-5. How to use remote controller Cooling / fan only operation Dry operation Automatic operation (auto changeover) Start Start Start START/STOP button ( START/STOP button ( Press this button to start the air conditioner. Press this button to start the air conditioner. START/STOP button ( Press this button to start the air conditioner.
Page 10
– 9 – Timer operation ON timer —> OFF timer Cancel the timer operation CAUTION (Stop —> Operation —> Stop) Press the CLR button. Use the wired remote controller for timer setting if it is You can use this setting to start the air conditioner •...
High power operation Preset operation Sleep timer operation Set your preferred operation mode for future use. To start the sleep timer (OFF timer) operation. High power (Hi POWER) The setting is memorized by the unit for future operation (except airflow direction). The Hi POWER (high power operation) mode automatically controls room temperature, fan speed and operation mode so that the room is quickly cooled.
– 11 – Wired remote controller This remote controller can control the operation of up to 8 indoor units. 4-1. Display section In the display illustration below all the icons are shown. When the unit is in operation, only relevant icons will be displayed. Display •...
4-2. Operation section 4-3. Correct usage Push each button to select a desired operation. When the air conditioner is used for the first time or when the setting is changed, follow the steps below. Settings are saved in • The control saves commands in memory and after the initial setting, there is no need for any additional memory and are displayed anytime the unit is turned on by pushing the button.
– 13 – 4-4. Timer operation 4-5. Power saving mode • Three timer modes are available: (Setting of up to 168 hours is enabled.) Case with wired remote controller Off timer : The unit stops when the set time is reached. The power saving mode saves energy by limiting the maximum current which will effect cooling capacity that the unit can generate.
Adjusting airflow direction Wired remote controller For best cooling, adjust the louvers (adjustment plates To automatically swing the airflow of up/down wind direction) appropriately. Cold air direction descends, so to, and to cool a room tilt them Perform this function when the air conditioner is in horizontally.
– 15 – How to set louver wind direction Determine wind direction of the selected Self clean mode louver by pushing individually • Each time you push the button, the display This function is provided to dry the inside of the indoor unit by the FAN operation after running the cooling changes as follows: Select an indoor unit to be set by pushing / dry / AUTO (cooling) mode to keep the indoor unit clean.
Operating air conditioner without remote Wireless remote controller A-B selection controller (temporary operation) Using 2 wireless remote controllers for the respective air conditioners, when the 2 air conditioners are closely installed. In the following cases, the air conditioner can be operate without remote controller with temporary operation button on the signal receiving unit.
– 17 – Advanced settings Standard swing Cyclic swing (Recommended for cooling) All four louvers swing simultaneously at the same All four louvers swing at different times like waves. angle. Case with wired remote controller How to set up swing type Swing Dual swing Adjoining louver alternately swing horizontally and...
Page 19
Setting the louver lock Releasing the louver lock Set “0000” in Step 4 of “Setting the louver lock”. UNIT LOUVER Push and hold the button (right side of mark disappears. the button) for at least 4 seconds while running is stopped. * Steps 1 - 3 and 5, 6 of “Setting blinks.
– 19 – Maintenance Check periodically • If the unit is used for a long time, parts may deteriorate and cause malfunction or bad drainage of dehumidified water depending on the heat, humidity, or dust. WARNING • In addition to the usual maintenance, it is recommended that you have the unit checked and maintained by the dealer where you purchased it.
Troubleshooting Case with wireless remote controller Check the points described below before requesting repair. <Representative examples> Contact the dealer from whom you purchased the air conditioner. Outdoor unit • A noise is heard when the power is turned on. • The outdoor unit is preparing for running. These LEDs do not light or -Power is not turned on.
– 21 – Case with wired remote controller Operations and performance If there is something unusual even after checking the above, stop running the unit, turn off the circuit breaker, and inform the Check before running Protective device dealer where you purchased the product of the product number and symptom. Do not attempt to repair the unit by yourself as doing so is dangerous.
Installation Do not install the air conditioner in the following places • Do not install the air conditioner in any place within 1 m from a TV, stereo, or radio set. If the unit is installed in such place, noise transmitted from the air conditioner affects the operation of these appliances. •...
Page 25
“Machinery” Directive (Directive 2006/42/EC) WARNING ELECTRICAL SHOCK HAZARD Disconnect all remote electric power supplies before servicing. • WARNING Moving parts. • Do not operate unit with grille removed. Stop the unit before the servicing. • CAUTION High temperature parts. You might get burned when removing this panel.
Page 28
– 27 – 3-1. 30°C 17°C ( (FAN) AUTO (LOW , LOW+ , MED , MED+ HIGH LOW+ MED+ AUTO (SWING) SWING (FIX) (OFF) (ON) (SET) (MODE) (CLR) A : Auto : Cool, : Dry, : Fan only (Hi-POWER) Cool 9-TH 10-TH 1115350208_EN-TH.indb 27...
Page 29
(PRESET) 3-2. AUTO (LOW , LOW + , MED + , HIGH : Dry (R03 [AAA]) (SLEEP) – Hi POWER (1, 3, 5 High Power Hi-POWER AM 0:00 • (R03 [AAA]) • • • • (A : Auto : Cool, : Dry, : Fan only) (17°C...