Download Print this page

Furuno NAVpilot-700 Installation Instructions Manual

Hide thumbs Also See for NAVpilot-700:

Advertisement

This information provides the instructions for the installation of the optional kit FAP-6300/6310.
This kit enables the NAVpilot-700/711 to automatically steer a EVC system equipped vessel
whose length is between 35 and 80 ft.
For the operation and installation of the autopilot, see documents below.
• NAVpilot-700/711: Operator's manual (OME-72720) and installation manual (IME-72720)
• NAVpilot-711C: Operator's manual (OME-72780) and installation manual (IME-72720)
Please read these safety instructions before you install or operate the equipment.
WARNING
WARNING
Do not open the equipment unless
you are well familiar with electrical
circuits.
Only qualified personnel should work
inside the equipment.
Do not lock the helm when the
autopilot controls the vessel.
Malfunction or accident can result.
Do not use the autopilot in the
following situations:
- Cruising speed is more than 40 kn
- Harbor entrance or narrow channel
- Where vessels change course often,
such as a cape or small island
- Poor visibility areas because of the
fog or rain, etc.
- When the vessel is stopped
Do not speed up suddenly when the
autopilot controls the vessel.
Do not raise the speed to 30-40 kn
within 30 seconds. The autopilot can
not calculate parameters under those
conditions. Malfunction or accident can
result.
When an alarm sounds, switch the
steering mode to the STBY mode
and then control the vessel with the
helm.
Malfunction or accident can result if the
vessel is steered automatically.
Notice for the discontinued model
The autopilot NAVpilot-711 is discontinued.
NAVpilot-700/711/711C
VOLVO IF KIT FAP-6300
YAMAHA HM IF KIT FAP-6310
INSTALLATION INSTRUCTIONS
For the heading sensor, use the
PG-700.
Use the rate gyro hybrid sensor (PG-700)
for the heading sensor. Install the
PG-700 away from metallic objects,
radiotelephone, and the antenna of a
radiotelephone. Malfunction or accident
can result if the sensor is too close to
those objects.
Do not input the heading data (output
from the autopilot) to the radar, etc.
The heading data output from the
autopilot is delayed for max 1 second
over the input data.
Follow the compass safe distances to
prevent interference to a magnetic
compass.
IF-700IPS
CAUTION
Standard
Steering
Compass
Compass
0.30 m
0.30 m

Advertisement

loading

Summary of Contents for Furuno NAVpilot-700

  • Page 1 INSTALLATION INSTRUCTIONS This information provides the instructions for the installation of the optional kit FAP-6300/6310. This kit enables the NAVpilot-700/711 to automatically steer a EVC system equipped vessel whose length is between 35 and 80 ft. For the operation and installation of the autopilot, see documents below.
  • Page 2 1. Materials Name Type Code No. Remarks IPS Interface Unit IF-700IPS Gateway unit VOLVO IPS Gateway AUTOPILOT-GATEWAY for FAP-6300 Gateway unit YAMAHA HM Gateway YAMAHA-HM-GATEWAY for FAP-6310 Cable Assy. MJ-A7SPF0005-020C 000-159-699-10 Self-tapping Screw 4x16 SUS304 000-162-605-10 Fuse FGMB 125V 1A PBF 000-157-478-10 Spare parts 2.
  • Page 3 2.2 Mounting Mounting considerations When selecting a location, keep in mind the following points. • Make sure the location is strong enough to support the unit under the conditions of continued vibration and shock normally encountered on the vessel. • Locate the unit away from heat sources. •...
  • Page 4 2.3 Wiring Connect the cable assy. (MJ-A7SPF0005-020C) and gateway unit to the IPS interface unit as shown below. IPS interface unit IF-700IPS Gateway unit Ground wire (IV-1.25sq.) Cable Assy. (MJ-A7SPF0005-020C, 2m) To the EVC system To processor unit FAP-7002 Connection with the processor unit FAP-7002 Connect the cable assy.
  • Page 5 Remove the outside cover of the processor unit; hold the right and left sides of the cover and pull the cover outward. Outside cover Remove the four screws circled below. Shield cover Cable clamp/fan assy. Remove the cable clamp/fan assy. from the shield cover. Note: When removing the cable clamp/fan assy., be careful not to apply tension to the fan connector.
  • Page 6 Connect the cable assy. (MJ-A7SPF0005-020C) to the connector blocks TB1 and TB7. Connection with TB1 (power) Clamp the power line of the cable assy. and power cable of processor unit with the crimping terminal, and then connect the + line (red) and - line (black) to the TB1 of the processor unit. For the crimping terminal, use rod terminals or plate shape pre-insulation terminals.
  • Page 7 Fuse replacement The fuse in the fuse holder on the + line (red) of the cable assy. (MJ-A7SPF0005-020C) protects the IPS interface unit from overcurrent and equipment fault. If you can not turn on the power, check if the fuse has blown. If the fuse has blown, find the reason before you replace the fuse. If the fuse blows again after the replacement, contact your dealer for advice.
  • Page 8: Initial Settings

    • NAVpilot-700/711: Installation manual (IME-72720) • NAVpilot-711C: Operator’s manual (OME-72780) The display examples in this section are shown for NAVpilot-700/711. Press the POWER/BRILL key or POWER/STBY key to turn on the power. The first time the system is powered, the language selection menu appears.
  • Page 9 Select [INSTALLATION] then push the knob to show the [INSTALLATION] menu. For how to set the [INSTALLATION] menu, see the document below. • NAVpilot-700/711: Installation manual (IME-72720) • NAVpilot-711C: Operator’s manual (OME-72780) Note1: The [INSTALLATION] menu can be opened from the STBY display by pressing the knob three times while pressing and holding down the MENU key.
  • Page 10 When the EVC system controls the rudder, the OVRD (override) mode is automatically enabled. The autopilot can not control the vessel in the OVRD mode. The display examples in this section are shown for NAVpilot-700/711. Note: The OVRD mode is enabled when [BOAT TYPE] is set to [EVCS BOAT].
  • Page 11 FAILED STARTUP TEST. System error of the IPS interface unit. Turn off the autopilot, con- PLEASE CONTACT A LO- tact your dealer. CAL FURUNO REPRE- SENTATIVE FOR REPAIR. NO CONNECT EVC INTER This message appears for the result of the startup test.
  • Page 13 18/Mar/2014 H.MAKI 電子署名者 : Maki DN: cn=Maki, c=JP - 日 Maki 本, o=FURUNO, ou=technicaldocument, email=hiromasa. maki@furuno.co.jp 日付 : 2014.03.18 13:12:41 +09'00'...
  • Page 14 17/Mar/2014 H.MAKI 電子署名者 : Maki DN: cn=Maki, c=JP - 日本, o=FURUNO, ou=technicaldocument, email=hiromasa. maki@furuno.co.jp 日付 : 2014.03.17 14:52:05 +09'00'...

This manual is also suitable for:

Navpilot-711cNavpilot-711