Start-Up And Use - Ariston CP 057 GT S Operating Instructions Manual

Start-up and use

GB
Using the hob
Lighting the burners
For each BURNER knob there is a complete ring showing the strength of the
flame for the relevant burner.
To light one of the burners on the hob:
1. Bring a flame or gas lighter close to the burner.
2. Press the BURNER knob and turn it in an anticlockwise direction so that it
is pointing to the maximum flame setting
3. Adjust the intensity of the flame to the desired level by turning the BURNER
knob in an anticlockwise direction. This may be the minimum setting , the
maximum setting or any position in between the two.
! If the flame is accidentally extinguished, switch off the burner and wait for
at least 1 minute before attempting to relight it.
If the appliance is equipped with a flame failure safety device*, press and
hold the BURNER knob for approximately 2-3 seconds to keep the flame
alight and to activate the device.To switch the burner off, turn the knob until
it reaches the stop position
The "separate double flame" burner*
This burner consists of two concentric burners which can operate either
together or separately.
Use of the double flame on the maximum setting gives a very high power
which reduces cooking times with respect to conventional burners.
Moreover the double flame crown provides a more uniform distribution of heat
on the bottom of the pan, when using both burners on minimum.
To ensure that the double-flame burner is used to its full potential,
never set the inside ring to minimum and the outside ring to maximum
at the same time.
Pots and pans of all sizes can be used. In the case of the smaller pots and
pans we recommend the use of only the internal burner.
There is a separate control knob for each of the "separate double flame"
burners.
The knob marked by the symbol
The knob marked by the symbol
To turn on one of the rings, press the relative knob in all the way and turn it
anti-clockwise to the high setting
The burner is fitted with an electronic igniter that automatically starts when
the knob is pressed in.
Since the burner is equipped with a safety device, after lighting the burner
keep the knob pressed in for about 2-3 seconds to allow the device which
keeps the flame lit automatically to heat up.
24
.
If the appliance is fitted with an electronic
lighting device* (see figure), press the
BURNER knob and turn it in an anticlockwise
direction, towards the minimum flame setting,
until the burner is lit. The burner might be
extinguished when the knob is released. If this
occurs, repeat the process, holding the knob
down for a longer period of time.
●
.
operates the external burner;
operates the internal burner.
.
The selected burner can be regulated using the corresponding knob, as
follows:
●
Off
Maximum
Minimum
To switch off the burner, turn the knob in a clockwise direction until it stops
●
(when reaches the " " position).
Practical advice on using the burners
For the burners to work in the most efficient way possible and to save on the
amount of gas consumed, it is recommended that only pans which have a lid
and a flat base are used. They should also be suited to the size of the burner.
Burner
Rapid (R)
Semi Rapid (S)
Auxiliary (A)
Triple Crown (TC)
Double Flame (DCDR internal)
Double Flame (DCDR external)
The hob is fitted with reducing pan stands, which should only be used on
auxiliary burner "A" and on the DC-DR (inner) "B".
A
For the best performance of your burners, keep the following in mind: All types
of pans can be used on the burners.
The important thing is that the bottom should be completely even.
WARNING! The glass lid can break in if it
is heated up. Turn off all the burners and
the electric plates before closing the lid.
Applies to the models with glass cover only.
Using the oven
! Before operating the product, remove all plastic film from the sides of the
appliance.
Ø Cookware diameter (cm)
24 - 26
16 - 20
10 - 14
24 - 26
10 - 14
26 - 28
b
WARNING ! The oven is provided
with a stop system to extract the
racks and prevent them from coming
out of the oven (1).
As shown in the drawing, to extract
them completely, simply lift the racks,
holding them on the front part, and
pull (2).