Aerial Connection; Auto Setup - Toshiba 19DV550P Service Manual

19-inch diagonal lcd tv/dvd combination

Hide thumbs Also See for 19DV550P:

Service manual (38 pages)

Service manual (76 pages)

Table Of Contents

Table of Contents

Remote Control

Install the batteries

Use batteries type UM4/R03 (AAA-Size).

Do not use old or weak batteries. The remote control may not work properly with a weak voltage from such

batteries. Replace exhausted batteries with new ones. Never try to recharge normal batteries - this could

cause an explosion.

Note:

Exhausted batteries can leak corrosive electrolyte, which may cause damage to the remote control -

therefore remove exhausted batteries immediately.

Open the battery

compartment.

Distance of Remote Control Operation

Remote sensor

Maximum distance approx. 5m

Transmitter window

The remote control handset will not work properly in the following cases:

If bright sunlight directly beams onto the unit front.

If the batteries have not been installed according to

their polarities.

51K0201A_ENG.indd 8

Auto setup

Your unit has an Automatic

installation which makes installation

in your unit easy. When you turn

on the unit for the first time, the

Automatic installation routine is

activated. Using this routine, you

can select the on-screen language

and automatically search for and

store all the receivable channels.

The Automatic station presetting

feature is for the set's built-in tuner

only. If you have a device such as

a digital decoder (eg. Satellite or

Digital Terrestrial) connected (see

page 43), you would need to tune it

in separately according to its own

instructions.

Note:

•

To cancel the Auto Tuning, press

EXIT during the process.

THE AUTOMATIC TUNNIG PROCESS

WILL ONLY START BY ITSELF THE

FIRST TIME YOU SWITCH THE SET

ON. HOWEVER YOU CAN RESTART

THIS PROCESS VIA THE MENU

SYSTEM (see page 12).

51K0201A_ENG.indd 10

Install the batteries as shown

Close the battery

below, ensuring the correct

compartment.

polarity.

Point the remote control

directly at the remote sensor.

If an obstacle is placed between the unit and the

handset.

If the batteries are weak.

Preparation:

Press

(Power) on the unit or press

(On/Standby) on

the remote control.

AUTO INSTALLATION menu will

appear.

AUTO INSTALLATION

Press

to select LANGUAGE,

LANGUAGE

then press ENTER. Press

COUNTRY

select desired language.

AUTO TUNING

Then press ENTER.

EXIT : END

Press

to select COUNTRY,

then press ENTER.

AUTO INSTALLATION

Press

to select your country.

LANGUAGE

Then press ENTER.

COUNTRY

AUTO TUNING

EXIT : END

Press

to select AUTO

TUNING, then press ENTER.

AUTO INSTALLATION

The confirmation screen will be

LANGUAGE

displayed. Press ENTER to start

COUNTRY

automatic tuning.

AUTO TUNING

Your TV will now automatically tune

in all available channels.

Note:

•

Please be patient - the Auto

EXIT : END

Tuning process can take

several minutes to complete.

When the programme on the

screen stops changing and the

sound comes on, the search

process is complete.

Note: Before you connect other appliances:

•

To avoid potentially damaging your set, make sure all items are switched off and disconnected from the

mains power when you make the connections.

•

Arrange the desired connection.

•

When you have finished making the connections, reconnect the mains power to the unit and switch it

back on.

Connect your aerial as shown below. Connections to other equipment is explained further on

pages 43~45. If you have problems with reception, consult a specialist of aerial.

(A) Power supply: Connect the supplied power cable to an AC 220-240V/50Hz mains power supply only

- do not attempt to connect it to any other type of supply. Never try to repair a damaged AC power cord

with isolation-tape - this should be repaired by a specialist or replaced. Do not let your pet loose near

the cable. Animals biting into the cable could receive a fatal electric shock, and could cause a hazard

to others.

(B) HEADPHONE jack: Plug headphones with a mini plug (3.5 mm) into this jack.

(D) AV2 input: Input for analogue A/V-Signal (Composite or S-Video). See page 45.

(E) PC MONITOR input (PC): See page 41.

(F) Scart socket (AV1): For the connection of scart cable. See pages 43~45.

(G) PC AUDIO input: See pages 41, 42.

(H) HDMI input : See page 42.

(I)

Aerial input socket: Connect the outdoor aerial to the aerial input socket as shown.

(J) Digital audio output: Digital output for CD/DVD (see page 44).

(K) Bracket holes: Fix a wall mounting bracket (not supplied) here.

9/12/08 4:54:29 PM

51K0201A_ENG.indd 9

Quick guide for MENU operation/Selecting the video input

Make sure the aerial connection and

power supply are connected as per

the description on previous page.

Preparations:

•

Turn on the unit with the

button on the unit. The

ENGLISH

indicator will light up in green.

GERMANY

To change the unit to standby mode,

press

(Power) indicator will change

from green to red. To turn on the unit

ENGLISH

from standby mode, press

MENU: RETURN

remote control again.

In standby mode, you can also turn

the unit on with

on the unit or P+/– on the remote

control.

ENGLISH

To turn off the unit press

GERMANY

button on the unit - to completely

switch it off, disconnect the mains

power supply.

•

Press TV/DVD to select the TV mode.

GERMANY

MENU: RETURN

ENGLISH

GERMANY

AUTO TUNING

10 %

MENU: RETURN

Note:

•

If no buttons are pressed for more

than approx. 60 seconds, the MENU

disappears automatically.

9/12/08 4:54:34 PM

51K0201A_ENG.indd 11

Back Side

(K)

(A)

(B) (C) (D)

(E) (F)

source/On-screen Language Selection

Quick guide for MENU operation

Call MENU and for example: Select AUTO TUNING.

Press INPUT.

Select TV. Press MENU.

(Power)

Press

to select

(Power)

on the remote control.

on the

Press

to select AUTO

TUNING, then press ENTER to

(Channel)

enter the AUTO TUNING menu.

... on the following pages the MENU

(Power)

can be called in the same way as

here.

Press EXIT to return to the normal screen.

Selecting the video input source

Press INPUT to view a signal from

another device connected to your TV,

such as a VCR or DVD player. You can

select each input source depending on

which input jacks you used to connect

your devices.

To select the video input source, press

/ . Then press ENTER within 6 seconds.

On-screen Language Selection

Select LANGUAGE (unless you

have already selected when the set

was first switched on).

Then press ENTER.

Press

to select the desired language.

Press EXIT to return to the normal screen.