Sanyo PLC-XP56 Service Manual page 9

Electrical Adjustments
No. Adjustment Item
2 Shootout Mode
3 Cooling Time
4 Hi-Land SW
5 V-Douki SW
6 Lamp Total Time
7 Net Board RESET
8 Keystone Option
9 Syukka SW
10 Color Shading SW
11 RC Enable/Disable
12 Lamp Dim Level
13 Lamp Warning Time
14 Forced NOBRAND
15 Forced Video Mute Off
16 ANZEN FAN Control Fix SW
17 DJTR_SW
18 HDCP Option
19 HDCP Reset
20 Auto PC Adj.
Group: 11 FAN (Fan Control)
0 FAN_TEMP_A_WARNING
1 FAN_TEMP_B_WARNING
2 FAN_TEMP_C_WARNING
3 FAN_TEMP_B-A_WARNING
4 FAN_TEMP_C-A_WARNING
5 FAN_CONTROL_SW
6 FAN1 Manual Out
7 FAN2 Manual Out
8 FAN4 Manual Out
9 FAN5 Manual Out
10 FAN6 Manual Out
11 FAN7 Manual Out
12 FAN1 Now Out
13 FAN2 Now Out
14 FAN4 Now Out
15 FAN5 Now Out
16 FAN6 Now Out
17 FAN7 Now Out
18 Temp Monitor A
19 Temp Monitor B
20 Temp Monitor C
21 Pressure Monitor
22 FAN_BALLAST_SW
23 Service Target MODE
24 Service Target FAN
25 Control Switch
26 Temp Source Range High
27 Temp Source Range Low
28 Temp Fan-Out Range High
29 Temp Fan-Out Range Low
30 Diff (UP)Src Range High
31 Diff (UP)Src Range Low
32 Diff(DWN)Src Range High
33 Diff(DWN)Src Range Low
34 Press Source Range Low
35 Press Source Range High
36 Press FanAdd Range High
37 Press FanAdd Range Low
38 Ceil-Add
39 Fan Out Limit Volt MAX
40 Fan Out Limit Volt MIN.
41 Fan Out Limit DAC MAX
42 Fan Out Limit DAC MIN.
43 Manual Out
44 Now Out
Group: 12 PC Real / AV Cinema
0 PC Real Contrast
1 PC Real Brightness
2 PC Real Color
3 PC Real Tint
4 PC Real Red
5 PC Real Green
Initial Value Range Input source / Description
0 0 ~ 1 0: Disable 1: Enable
3 0 ~ 15 Set cooling period, 1: 30 sec. 3: 90 sec. 15: 450 sec. 0: continuos
0 0 ~ 1 0: Normal 1: Highland mode (Fan spin speed max.)
0 0 ~ 1 0: Synchronized Vertical 1: non-synchronized Vertical
- 0 ~ 65535 Read only
1 0 ~ 1 0: Disable
0 0 ~ 1 0: Maximum correction (fix) 1: Changeable for Input signal
0 0 ~ 10 Set 10 to Shipping Condition
1 0 ~ 1 0: OFF 1: ON
0 0 ~ 3 0: Both enable 1: Front Disable 2: Rear Disable 3: Both Disable
15 0 ~ 15 0: the darkest 1: the brightest
1500 0 ~ 65535 Unit = hour
0 0 ~ 1 0: Normal 1: No brand
0 0 ~ 1 0: Video Mute ON 1: Video Mute OFF
0 0 ~ 4 0: Normal 1: Normal min. 2: Normal max 3: Eco min. 4: Eco max
- - Not used
0 0 ~ 3 0: XGA 1: Not XGA
0 0 ~ 10 Set 10 and write EDID Data for HDCP
0 0 ~ 1 0: Auto PC adj available, 1: Auto PC adj. not available
460 30 ~ 1000 Temperature to judge abnormal A (Not memorized) Inside projector
800 30 ~ 1000 Temperature to judge abnormal A (Not memorized) Lamp
510 30 ~ 1000 Temperature to judge abnormal A (Not memorized) LCD Panel
520 0 ~ 1000
200 0 ~ 1000
0 0 or 1 0: Auto-control all Fans 1: Manual control all Fans
1350 0 ~ 2000 These are effective when FAN_CONTROL_SW is set to "1".
1350 0 ~ 2000
1350 0 ~ 2000
1350 0 ~ 2000
1350 0 ~ 2000
1350 0 ~ 2000
- Read only Reading voltage of each Fan
-
-
-
-
-
- - Read only
- -
- -
- - Read only
0 0 or 1 Fan control depend on Ballast Output Voltage 0: OFF 1: ON
-1 -1 ~ 3 -1: Current Mode 0: Normal Mode 1: Eco Mode
0 0 ~ 5 Service taget 0: FAN1 1: FAN2 2: FAN4 3: FAN5 4: FAN6 5: FAN7
0 Control Switch for the operated Fan 0: Auto 1: Manual
400 Control range of Temperature for Temperature Sensor A
330
1350 / 1000 Control range of Fan control voltage by Temperature Sensor A
780 / 700 / 1000
180 Difference of temperature between temp-A and temp-C for Fan additional voltage (upward)
150
80 Difference of temperature between temp-A and temp-C for Fan additional voltage (downward)
60
Control range of Pressure Sensor
0 Control range of Fan additional voltage by Pressure sensor
500
Fan additional voltage when ceiling
1400 Limit voltage of current Fan output voltage
650
0 ~ 255 Limit of DAC output for current Fan
0 ~ 255
0 ~ 2000 Output voltage of current Fan at manual mode
- Reading voltage of current Fan
32 0 ~ 63
32 0 ~ 63
32 0 ~ 63
32 0 ~ 63
32 0 ~ 63
30 0 ~ 63
1: Enable
-9-
✻
Fan adjustment [Setting]
✻
Fan adjustment [max.]
✻
Fan adjustment [min.]