Table of Contents
Advertisement
Monro-Manual-1-50
ssic
3.
Lift out spool that is not engaged by lever;
then move lever aside and lift out other spool.
Cartridge
4.
Holding new spools over spindles with black
band up and exposed portion of ribbon on side
n
nearest print wheels, place one spool on
spindle not engaged by lever. Rotate spools to
be sure its pins engage in spindle gear.
5.
Thread ribbon around guides and between
print wheels and platen.
Changing
6.
Install other spool and rotate to engage
spindle gear and also to take up slack in
ribbon.
nroe Classic
the Paper Tape
7.
Replace printer cover.
Ribbon Cartridge
.
Installing Paper Tape
(Note how ribbon
51M Ribbon
between print
onroe Classic
To ensure ease of installation, read the instructions
and up).
completely before installing a new paper roll. Then
e Ribbon Cartridge
follow the instructions step-by-step.
1.
Tear off excess paper at the tear-off knife.
P51M Ribbon
To remove cover, place thumbs on serrated
2.
surfaces located on each side of the cover.
Pressing down with your thumbs, slide the top
cover toward the back of the calculator. Once
the cover has been pushed back approximately
s paper tape.
1", lift the cover off.
inter cover. (Note how ribbon
guides and between print
ten; black band up).
g the lever to the
ss paper tape.
out cartridge.
printer cover. (Note how ribbon
spindles with black
d guides and between print
on of ribbon on side
laten; black band up).
cartridge on
ge...
3.
Lift up and remove old paper roll from the
paper roll holders. Tear off paper between the
used paper roll and the printer. Pull remaining
paper through the printer by continuously
ge by moving the lever to the
lifting the leading edge (nearest display).
ove and lift out cartridge.
artridge over spindles with black
xposed portion of ribbon on side
heels, place cartridge on
gage cartridge...
dge by moving the lever to the
move and lift out cartridge.
cartridge over spindles with black
exposed portion of ribbon on side
wheels, place cartridge on
ssic
ngage cartridge...
4.
With the leading edge of the new paper roll,
feeding from the bottom, place the new roll
into position between the two flexible paper
n
roll holders.
cover.
5.
Feed the paper into the rear of the printer
mechanism until it meets resistance
nroe Classic
(approximately 1 to 1.5 inches). Depress the
paper advance button until the paper extends
Ribbon
several inches beyond the printer mechanism.
er cover.
65M Ribbon
.
(Note how ribbon
Monroe Classic
ls, around guides
and platen, black
e Ribbon
P65M Ribbon
s paper tape.
inter cover. (Note how ribbon
1/26/10
6:07 PM
3.
Lift out spool that is not engaged by lever;
then move lever aside and lift out other spool.
4.
Holding new spools over spindles with black
band up and exposed portion of ribbon on side
nearest print wheels, place one spool on
3.
spindle not engaged by lever. Rotate spools to
Lift out spool that is not engaged by lever;
then move lever aside and lift out other spool.
be sure its pins engage in spindle gear.
5.
4.
Thread ribbon around guides and between
Holding new spools over spindles with black
print wheels and platen.
band up and exposed portion of ribbon on side
nearest print wheels, place one spool on
6.
Install other spool and rotate to engage
spindle gear and also to take up slack in
spindle not engaged by lever. Rotate spools to
be sure its pins engage in spindle gear.
ribbon.
5.
Thread ribbon around guides and between
7.
Replace printer cover.
print wheels and platen.
6.
Install other spool and rotate to engage
Installing Paper Tape
spindle gear and also to take up slack in
ribbon.
To ensure ease of installation, read the instructions
Replace printer cover.
7.
completely before installing a new paper roll. Then
follow the instructions step-by-step.
1.
Tear off excess paper at the tear-off knife.
Installing Paper Tape
2.
To remove cover, place thumbs on serrated
To ensure ease of installation, read the instructions
surfaces located on each side of the cover.
completely before installing a new paper roll. Then
Pressing down with your thumbs, slide the top
follow the instructions step-by-step.
cover toward the back of the calculator. Once
1.
the cover has been pushed back approximately
Tear off excess paper at the tear-off knife.
2.
1", lift the cover off.
To remove cover, place thumbs on serrated
surfaces located on each side of the cover.
Pressing down with your thumbs, slide the top
cover toward the back of the calculator. Once
the cover has been pushed back approximately
1", lift the cover off.
3.
Lift up and remove old paper roll from the
paper roll holders. Tear off paper between the
used paper roll and the printer. Pull remaining
paper through the printer by continuously
lifting the leading edge (nearest display).
3.
Lift up and remove old paper roll from the
paper roll holders. Tear off paper between the
used paper roll and the printer. Pull remaining
paper through the printer by continuously
lifting the leading edge (nearest display).
4.
With the leading edge of the new paper roll,
feeding from the bottom, place the new roll
into position between the two flexible paper
roll holders.
4.
With the leading edge of the new paper roll,
feeding from the bottom, place the new roll
into position between the two flexible paper
roll holders.
5.
Feed the paper into the rear of the printer
mechanism until it meets resistance
(approximately 1 to 1.5 inches). Depress the
paper advance button until the paper extends
several inches beyond the printer mechanism.
5.
Feed the paper into the rear of the printer
mechanism until it meets resistance
Page 9
6.
Feed the paper through the opening of the
tear-off knife and lay top cover flat on the
calculator leaving a 1" overhang at the back
of the top cover. Apply a firm downward
and forward pressure, slide the top cover
forward until it snaps into position.
7.
Tear off any excess paper.
6.
Feed the paper through the opening of the
Spare Supplies
tear-off knife and lay top cover flat on the
Storage Compartment
calculator leaving a 1" overhang at the back
of the top cover. Apply a firm downward
and forward pressure, slide the top cover
6.
forward until it snaps into position.
Feed the paper through the opening of the
tear-off knife and lay top cover flat on the
7.
Tear off any excess paper.
calculator leaving a 1" overhang at the back
of the top cover. Apply a firm downward
and forward pressure, slide the top cover
forward until it snaps into position.
7.
Tear off any excess paper.
Spare Supplies
Storage Compartment
Spare Supplies
Storage Compartment
9
Hide quick links:
Advertisement
Table of Contents
