Figure 5-6
5.4.4
How To Order
ComPair order codes:
•
Starter kit ComPair + SearchMan software + ComPair
interface (excluding transformer): 4822 727 21629
•
ComPair interface (excluding transformer): 4822 727
21631
•
Starter kit ComPair software (registration version): 4822
727 21634
•
Starter kit SearchMan software: 4822 727 21635
•
ComPair CD (update): 4822 727 21637
•
SearchMan CD (update): 4822 727 21638
•
ComPair interface cable: 3122 785 90004
5.5
Error Buffer
The error code buffer contains all detected errors since the
last time the buffer was erased. The buffer is written from left
to right. When an error occurs that is not yet in the error code
buffer, it is written at the left side and all other errors shift one
position to the right.
5.5.1
How to Read the Error Buffer
Use one of the following methods:
(UURU
'HYLFH
1RW DSSOLFDEOH
1RW DSSOLFDEOH
1RW DSSOLFDEOH
7'$7'$
5HVHUYH
063; 7'$
7'$[[
,ð& EXV
$1
1RW DSSOLFDEOH
0&
7XQHU
7'$
0
Service Modes, Error Codes and Fault Finding
PC
VCR
Power
I
2
C
9V DC
86532027_003.EPS
050898
(5525 &2'( 7$%/(
(UURU GHVFULSWLRQ
1R (UURU
;5D\RYHUYROWDJH SURWHFWLRQ 86$ RQO\
+RUL]RQWDO SURWHFWLRQ
9HUWLFDO SURWHFWLRQ
063 ,ð& LGHQWLILFDWLRQ HUURU
325 9 9 SURWHFWLRQ
*HQHUDO ,ð& EXV HUURU
3RZHU GRZQ RYHU FXUUHQW SURWHFWLRQ
(: SURWHFWLRQ /DUJH 6FUHHQ
190 ,ð& LGHQWLILFDWLRQ HUURU
7XQHU ,ð& LGHQWLILFDWLRQ HUURU
%ODFN FXUUHQW ORRS SURWHFWLRQ
3,3 ,ð& LGHQWLILFDWLRQ HUURU
•
On screen via the SAM (only if you have a picture).
Examples:
–
ERROR: 0 0 0 0 0 : No errors detected
–
ERROR: 6 0 0 0 0 : Error code 6 is the last and only
detected error
–
ERROR: 9 6 0 0 0 : Error code 6 was first detected
and error code 9 is the last detected (newest) error
•
Via the blinking LED procedure (when you have no
picture). See next paragraph.
•
Via ComPair.
5.5.2
How to Clear the Error Buffer
The error code buffer is cleared in the following cases:
•
By activation of the CLEAR command in the SAM menu:
•
When you exit SDM / SAM with the STANDBY command
on the remote control (when leaving SDM / SAM, by
disconnecting the set from Mains power, the error buffer
is not reset).
•
When you transmit the command DIAGNOSE-99-OK
with ComPair.
•
If the content of the error buffer has not changed for 50
hours, it resets automatically.
5.5.3
Error Codes
In case of non-intermittent faults, clear the error buffer before
you begin the repair. These to ensure that old error codes are
no longer present.
If possible, check the entire contents of the error buffer. In
some situations, an error code is only the result of another
error code and not the actual cause (e.g., a fault in the
protection detection circuitry can also lead to a protection).
'HI LWHP
9ORW$X[9
RU
5*% DPSV &57
Figure 5-7
L01.1E
5.
'LDJUDP
$
$
$ $
$ RU $
$ $ $ $ $
$
$ $
$
$
$ $
% %
3
CL 16532008_047.pdf
GB 17
210501