All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by RB 0172 Service PaCE...
EN 2 L01H.2E Technical Specifications, Connections and Chassis Overview 1. Technical Specifications, Connections and Chassis Overview Note: Described specifications are valid for the whole product : NTSC 4.43 (playback range. only) Channel selections : 100 channels : UVSH Technical Specifications IF frequency : 38.9 MHz...
Page 3
Technical Specifications, Connections and Chassis Overview L01H.2E EN 3 10 - 32 PIN SMART CARD CONNECTOR (0.7 Vpp / 75 Ω) 11 - Green / Y 12 - 13 - 14 - (0.7 Vpp / 75 Ω) 15 - Red / V 0 - 0.4 V: INT 1 - 3 V: EXT / 75 Ω...
EN 4 L01H.2E Safety & Maintenance Instructions, Warnings, and Notes 2. Safety & Maintenance Instructions, Warnings, and Notes Safety Instructions For Repairs Warnings Safety regulations require that during a repair: • In order to prevent damage to ICs and transistors, avoid all •...
Mechanical Instructions L01H.2E EN 7 4. Mechanical Instructions Note: Figures below can deviate slightly from the actual situation, due to the different set executions. Rear Cover Removal 1. Remove all (seven) fixation screws of the rear cover: two at the top, two at each side and one near the mains cord holder.
EN 8 L01H.2E Service Modes, Error Codes and Fault Finding 5. Service Modes, Error Codes and Fault Finding Index: – 475.25 MHz for PAL/SECAM (Europe and AP-PAL) 1. Test points. • Colour system: 2. Service Modes. – PAL-M for LATAM BI/TRI/FOUR-NORMA.
Page 9
Service Modes, Error Codes and Fault Finding L01H.2E EN 9 – (Europe: 1 = Basic, Basic Plus and System, CSM Menu English, French, German and Italian) AAAABC – (AP: 1 = Z, R and Y System, English, Malay and CODE Simplified Chinese) –...
Page 10
EN 10 L01H.2E Service Modes, Error Codes and Fault Finding 2. Select the INSTALLATION sub menu. 5.3.2 Sound Problems 3. Select and change the SYSTEM setting until picture and sound are correct. No Sound or Sound too Loud (After Channel Change / 4.
Page 11
Service Modes, Error Codes and Fault Finding L01H.2E EN 11 The Blinking LED Procedure • Set is non-stop in hiccup mode Set is in over current mode; check the secondary sensing (opto coupler 7515) and the 'MainSupply' voltage. Signal Via this procedure, you can make the contents of the error 'Stdby_con' must be logic low under normal operation buffer visible via the front LED.
Page 12
EN 12 L01H.2E Service Modes, Error Codes and Fault Finding Personal Notes:...
Block- and Wiring Diagram, Testpoints, I2C, and Supply Voltage Over- L01H.2E 6. Block- and Wiring Diagram, Testpoints, I C, and Supply Voltage Overview Block Diagram 0240 SP/LS (For PRO-BASIC and SYSTEM) CLOCK INTERFACE (only for "SYSTEMS" sets) AUDIO AMPLIFIER FRONT CONTROL CONTROL +3.3V...
Block- and Wiring Diagram, Testpoints, I2C, and Supply Voltage Over- L01H.2E Testpoint Overview Main Panel Copper Track Side AUDIO OUTPUT 7901 OR 7902 500mV / div DC 500mV / div DC 1V / div DC 250ns / div 5ms / div 20us / div TV-PROC.
Page 16
Block- and Wiring Diagram, Testpoints, I2C, and Supply Voltage Over- L01H.2E C and Supply Voltage Diagram POWER SUPPLY LINE DEFLECTION 6560 5445 VIDEO ANODE CRT OUTPUTS 150 - 250V FOCUS FOCUS 3336 6561 MAIN SUPPLY 3487 FOCUS CRT C-7332 SINGLE RANGE...
Alignments L01H.2E EN 45 8. Alignments Index: 8.2.1 Vg2 Adjustment (AKB method) General Alignment Conditions Hardware Alignments 1. Connect the RF output of a pattern generator to the Software Alignments and Settings antenna input. Test pattern is a 'black' picture (blank screen on CRT without any OSD info).
Page 46
122 0 ON / OFF 17HT5404/01Z 8 122 0 WIDESCREEN ON / OFF 17HT5404/05Z 8 122 0 TUNER NONE / APLS / PHILIPS 17HT5404/21R 8 122 0 ON / OFF 17HT5404/25R 8 122 0 RADIO ON / OFF 21HT3154/01 117 0...
Page 47
Radio 1 = Tuner has FM radio feature and TV chasis support FM radio 1 = Tuner has LNA feature Tuner 0 = None (no tuner), 1 = Philips (model), 2 = Alps (model) Byte 3 Not Used (Devices) Not Used...
Page 48
EN 48 L01H.2E Alignments 8.3.2 Deflection 8.3.4 White Tone The Deflection Sub menu contains the following items: White Tone Menu • AKB, ON to enable, OFF to disable the 'black current loop' (AKB = Auto Kine Bias). • Brightness, (set Brightness) •...
Page 49
Alignments L01H.2E EN 49 8.3.5 Geometry • Select Vertical Zoom to align the vertical linearity over the entire screen height (for 16 : 9 applications only). • Set Trapezium Correction to align the lines at the vertical The geometry alignments menu contains several items to align sides.
EN 50 L01H.2E Circuit Description 9. Circuit Description Index of this chapter: 1. Introduction The L01 is divided into 2 basic systems, i.e. mono and stereo 2. Audio Signal Processing sound. While the audio processing for the mono sound is done 3.
Page 51
Circuit Description L01H.2E EN 51 AUDIO SOURCE SELECTION EXT. AUDIO 7801 7861 INPUT 7831 EXT. AUDIO OUT CONTROL AUDIO DECODING 7209 7210 7901 PROCESSING SELECTION FM IF MATR. SWITCH AUDIO BUFFER AMPL. 7834 7835 7200 RF ANT. SOUND FM ANT.
Page 52
EN 52 L01H.2E Circuit Description 9.2.3 FM radio (if present) 7200 The FM radio uses the 10.7 MHz concept. This SIF frequency is available at pin 10 of the tuner. Via a pre-amplifier (TS7209 RGB/YUV INSERT 56 58 PANEL and TS7210), the signal is fed for demodulation to either the...
Page 53
Circuit Description L01H.2E EN 53 signal. It operates in such a way that maximum stretching 9.3.7 RGB Amplifier is obtained when signals with a low video level are received. For bright pictures, stretching is not active. From outputs 56, 57 and 58 of IC7200, the RGB signals are •...
Page 54
EN 54 L01H.2E Circuit Description 9.5.2 Vertical Drive SUPPLY START-UP V CC DRAIN A divider circuit performs the vertical synchronisation. The MANAGEMENT CURRENT SOURCE clamp vertical ramp generator needs an external resistor (R3245, pin internal UVLO start n.c. VALLEY supply M-level 20) and capacitor (C2244, pin 21).
Page 55
Circuit Description L01H.2E EN 55 Degaussing Control Circuit B1/B2 Main Supply Focus n⋅V Mains AC Input Main Power Panel VideoSupply Supply Main Aux Filament Tilt& Rotation Degaussing GATE Circuit VlotAux +13V 3V3 Reg. Correction Horizontal Vaux Deflection GATE +3.9V +3.3V...
Page 56
EN 56 L01H.2E Circuit Description The moment that the voltage on pin 1 drops below the ‘under voltage lock out‘ level (UVLO = ± 9 V), the IC will stop switching and will enter a safe restart from the rectified mains voltage.
Page 57
Circuit Description L01H.2E EN 57 In Standby, the power supply works in ‘burst mode’. Burst mode can be used to reduce the power consumption Active/ below 1 W at stand-by. During this mode, the controller is active inactive (generating gate pulses) for only a short time and for a longer time inactive waiting for the next burst cycle.
Page 58
EN 58 L01H.2E Circuit Description Over Power Protection 9.7.1 Introduction During the primary stroke, the rectified AC input voltage is measured by sensing the current drawn from pin 4 (DEM). This The microprocessor part of the UOC has the complete control current is dependent on the voltage on pin 9 of transformer and teletext on board.
Page 59
Circuit Description L01H.2E EN 59 – 9.5 to 12 V: EXTERNAL 4:3 Abbreviation list • SEL-MAIN-FRNT-RR This is the ‘source select control’ signal from the microprocessor. This control line is under 2 Carrier (or Channel) Stereo user control or can be activated by the other two control Automatic Channel Installation: lines.
Page 60
EN 60 L01H.2E Circuit Description Horizontal Flyback Pulse: horizontal Serial Clock sync pulse from large signal deflection Serial Data Headphone Service Default Mode Colour phase control for NTSC (not SECAM SEequence Couleur Avec Memoire. the same as ‘Tint’) Colour system mainly used in France Monochrome TV system.