Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Datavideo HBT-11
Summary of Contents for Datavideo HBT-11
-
Page 2: Table Of Contents
Table of Contents FCC COMPLIANCE STATEMENT ........4 WARNINGS AND PRECAUTIONS ........4 WARRANTY ..............6 ............. 6 TANDARD ARRANTY ............. 6 ARRANTY DISPOSAL ................ 7 1. INTRODUCTION ............8 ..............8 EATURES 2. SYSTEM DIAGRAM ............9 3. CONNECTIONS ............10 .............. - Page 3 Datavideo Technologies is not responsible for any omissions or errors, or for any subsequent loss or damage caused by using the information contained within this manual.
-
Page 4: Fcc Compliance Statement
This product should only be operated from the type of power source indicated on the marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company. - Page 5 10. Make sure that the total amperes of all the units that are plugged into a single wall outlet do not exceed 15 amperes. 11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they may touch dangerous voltage points or short out parts that could result in risk of fire or electric shock.
-
Page 6: Warranty
DVD Drives, Hard Drives are only covered for the first 10,000 hours, or 1 year (whichever comes first). Any second year warranty claims must be made to your local Datavideo office or one of its authorized Distributors before the extended... -
Page 7: Disposal
It must be handed over to the applicable take back scheme for the recycling of Waste Electrical and Electronic Equipment. For more detailed information about the recycling of this product, please contact your local Datavideo office. -
Page 8: Introduction
The transmitter allows transmission of up to 4K image quality video. With the 48V power connected to one end of the HBT-11 HDBaseT receiver, the HBT-11 will thus be able to power the transmitter by Power over Ethernet (PoE). On the transmitter end (HBT-10), there is also a 12V/30W DC output serving to supply power to backend devices. -
Page 9: System Diagram
2. System Diagram... -
Page 10: Connections
HDMI OUT HDMI port for video output. DVIP Port Connects to Ethernet switch or router, serving as a communication port between the network and the HBT-11 receiver. 48V DC IN 48V DC power input connection Power LED Indicator ON: Power connected... -
Page 11: Front Panel
Front Panel HDBaseT Port Connects between HBT-10 transmitter and HBT-11 receiver. RS-232/RS-422 Interface (Phoenix Terminal) Connects to external RS-232/RS-422 device. RX: Receiver PIN (differential pair if RS-422 is enabled) TX: Transmitter PIN (differential pair if RS-422 is enabled) G: Ground PIN DIP Switch DIP Switch selects RS-232 or RS-422. -
Page 12: Rs-422 Connection
4. RS-422 Connection To use the RMC-180 PTZ Camera Control Unit to control the PTZ-150 camera behind the HBT-11 Receiver box, please connect the RMC-180 to the HBT-11 by the RS-422 wiring scheme as shown below. HBT-11 Receiver Box RMC-180 Controller... -
Page 13: Dimensions
5. Dimensions All measurements in millimeters (mm) 6. Specifications Video / Audio Input HDMI x 1 Output HDBaseT RJ-45 x 1 Control DVIP Ethernet RJ-45 x 1 Phoenix Terminal RS-422 / RS-232 Pitch 3.50 mm Power DC IN DC 48 V Dimensions L x W x H 131.8 x 85 x 45.2 mm... - Page 14 Video Resolutions (HBT-10/HBT-11 Pair ONLY) Cable Range Video Resolution Up to 1080p, 60Hz, 36 bpp. 100 meters Data rates lower than 5.3 Gbps CAT5e/6 or below 255 MHz TMDS clock. Ultra HD video formats: 70 meters HDMI Deep color: 1080p, 60, 48 bpp.
-
Page 15: Service And Support
Service and Support...