VQT9306 Video Cassette Recorder NV-FJ620 Series NV-FJ625AM Operating Instructions Contents Warning and Important Information Controls and Components Connections Tuning the TV to Your VCR Storing TV Broadcasts in Your VCR Preparations for G-Code Programming Settings Using the On Screen Display...
Plus, [Alumina] Head Cleaner further enhanced cleaning efficiency. – Based on in-house tests with Panasonic video cassettes. Actual head life may vary according to conditions of use, tape type, temperature, humidity, etc. Cautions before you operate this VCR Avoid: –...
NAVI INDEX INPUT SELECT SEARCH PICTURE MODE MENU G-CODE/SV DATE CANCEL SPEED PROG. / CHECK TIMER Á DISPLAY RESET AUDIO VCR/TV STOP PLAY TIMER REC REC/OTR /REW SEARCH IN (AV1) OUT VIDEO AUDIO POWER DIRECT REC OSD REPEAT Í VOLUME –...
Page 4
TV. simultaneously until the [! " hold] indication appears in the VCR display. the [! " hold] indication appears in the VCR display to inform you that no operation is possible. simultaneously until the [! " hold] indication disappears.
Notes: – If you are using a Panasonic TV, this setting has already been made, and so you do not need to perform the above setting procedure. However, this remote control may not work with some Panasonic TVs.
Tuning the TV to Your VCR The VCR supplies a signal to the TV via the RF coaxial cable on channel E21–E69. It is possible to view the video picture on your TV in the same way that you watch TV broadcasts.
Storing TV Broadcasts in Your The VCR is fitted with its own tuner (just like a normal TV) and can be preset to receive up to 99 TV broadcast stations. Plug in Auto Tuning When the VCR is turned on after connecting the aerial cable and the mains lead, Auto Tuning starts.
Page 8
Press the Cursor buttons (34) SYSTEM] then select [AUTO] by pressing the Cursor buttons (21) – The VCR automatically distinguishes between PAL, SECAM and NTSC broadcasts. – If the picture lacks colour when [AUTO] is selected, select [MESECAM], [PAL] or [NTSC (For NV-FJ620BD/BDX)].
To Add and Delete the Channel Example: If you want to add a new channel between Channel 4 and Channel 6, 1 Press the MENU button to display the Main menu on the TV screen. 2 Press the Cursor buttons (34) to select [CH ADD&DELETE] then press the OK button 3 Press the Cursor buttons (34)
Language Setting of the On Screen Display Select one of the three languages displayed: English, Arabic and Russian. Preparations – Confirm that the TV is on and the VCR viewing channel is selected. – Turn on the VCR. Operations Press the MENU button display the Main menu on the TV screen.
Preparations – Set the clock of the VCR. See page 10. – Store TV broadcasts in your VCR. See pages 7–9. – Confirm that the TV is on and the VCR viewing channel is selected. – Turn on the VCR.
Settings Using the On Screen Display Preparations – Confirm that the TV is on and the VCR viewing channel is selected. – Turn on the VCR. – Set the VCR/TV switch to [VCR]. To Set the Colour TV System Press the MENU button display the Main menu on the TV screen.
Playback Preparations – Confirm that the VCR is on. – Confirm that the TV is on and the VCR viewing channel is selected. – Insert a recorded video cassette. For Normal Playback: Press the Play button For Cue or Review Playback:...
EJECT button will eject the cassette and automatically turn itself off again. VCR-off Search When the VCR is off, the VCR starts intro-jet scan of an inserted cassette by pressing the SEARCH button To Eject Video Cassette Using the Remote...
Recording Preparations – Confirm that the VCR is on. – Confirm that the TV is on and the VCR viewing channel is selected. – Set the VCR/TV switch to [VCR]. Operations Insert a video cassette with an intact erasure prevention tab.
Page 17
To Stop the OTR Recording Before the End: Press the Stop button Notes: – The OTR function works during normal recording. – When the tape reaches its end during OTR, the VCR will turn itself off. to start to select the programme to start recording.
Notes: – If you leave the VCR in the recording pause mode for more than 5 minutes in step 3 or 6, the VCR automatically switches over to the stop mode to protect the video heads.
Preparations – Confirm that the VCR is on. – Confirm that the TV is on and the VCR viewing channel is selected. – Insert a video cassette with an intact erasure prevention tab.
Page 20
TIMER (REC) button so that the [Á] indication on the VCR display disappears. However, after you have finished using the VCR, be sure to reactivate the timer recording standby mode by pressing the TIMER (REC) button again otherwise the programmed timer recording will not be performed.
Checking a Timer Programme – The VCR must be turned on, or in timer recording standby mode. – Confirm that the TV is on and the VCR viewing channel is selected. 1 Press the PROG./CHECK button twice. – Every time you press the PROG./...
Gemstar Development Corporation. Preparations – Confirm that the VCR is on. – Confirm that the TV is on and the VCR viewing channel is selected. – Insert a video cassette with an intact erasure prevention tab.
Conditions for correct operation of the Jet Navigator function: – The tape length of the inserted cassette must be set correctly. – The VCR must not be in the timer recording standby mode. – A programme of at least 15 minutes must be recorded on the tape.
Stamp) appears on the TV screen for approx. 5 seconds. Preparation – Display the VCR picture on the TV. Note: – Time Stamp does not appear if the beginning of the Jet Navigator data are not recorded 10 minutes before and after the current tape position in the EP mode even when index signals are recorded.
– When you press the REC button during recording. Conditions for correct operation of the Index search function: – The VCR must be in the stop mode or in the playback mode. – Each programme recorded on the tape must be at least 5 minutes long.
– Connect the audio equipment or a video movie camera to this VCR with an audio cable. – Display the VCR picture on the TV. – Insert the cassette on which the audio dubbing is to be performed, and make sure that its erasure prevention tab is not broken out.
[The VCR display is not illuminated.] – The mains lead has not been connected. Connect the mains lead to the mains supply. [The VCR display is illuminated but the VCR will not operate.] ), TIMER (REC) button – The VCR is in the timer mode.
[The remote control does not operate correctly.] – The remote control transmitter beam is not reaching the VCR. Ensure that the remote control is being pointed at the VCR and that the transmitter beam is not obstructed. – The distance is too far.