Sign in today to find solutions:

Don't have an account? Sign up

Panasonic ADVANCED HYBRID KX-TEA308 Getting Started Manual

Panasonic amplified phone user manual.

 
Thank you for purchasing a Panasonic Advanced Hybrid System.
Please read this manual carefully before using this product and save this manual for future use.
Advanced Hybrid System
Getting Started
Model
KX-TEA308
KX-TEB308
Next page ->

Summary of Contents

  • Page 1

    Thank you for purchasing a Panasonic Advanced Hybrid System. Please read this manual carefully before using this product and save this manual for future use. Advanced Hybrid System Getting Started KX-TEA308 KX-TEB308 Model...

  • Page 2

    System Components System Components Table Main Unit Optional Service Cards Proprietary Equipment Taiwan: 4 PT Extensions For supported extension types, refer to "2.3 Connecting Extensions". Notice Certain models may not be available in your country/area. Getting Started Model KX-TEA308 Advanced Hybrid System: 3 Outside (CO) Lines, 8 Hybrid Extensions KX-TEB308 Advanced Hybrid System: 3 Outside (CO) Lines, 4 Hybrid...

  • Page 3

    Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: Read and understand all instructions. Follow all warnings and instructions marked on the product. Unplug the product from the wall outlet before cleaning.

  • Page 4

    SLT is connected to. Contact your telephone company. If all SLTs operate properly, there may be a problem with your PBX. Do not reconnect the PBX to the outside (CO) lines until it has been serviced by an authorised Panasonic Factory Service Centre.

  • Page 5

    UNPLUG THIS UNIT FROM THE AC OUTLET IF IT EMITS SMOKE, AN ABNORMAL SMELL OR MAKES UNUSUAL NOISE. THESE CONDITIONS CAN CAUSE FIRE OR ELECTRIC SHOCK. CONFIRM THAT SMOKE HAS STOPPED AND CONTACT AN AUTHORISED PANASONIC FACTORY SERVICE CENTRE. • WHEN RELOCATING THE EQUIPMENT, FIRST DISCONNECT THE TELECOM CONNECTION BEFORE DISCONNECTING THE POWER CONNECTION.

  • Page 6

    If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE AC OUTLET IN YOUR PREMISES, THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.

  • Page 7

    How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse and fuse cover. The equipment must be connected to direct extension lines, and a payphone should not be connected as an extension. 999 and 112 can be dialled on the apparatus after accessing the Exchange line for the purpose of making outgoing calls to the BT emergency services.

  • Page 8: Table Of Contents

    Table of Contents Before Installation ... 9 Unpacking...9 System Connection Diagram ...10 Installation... 11 Opening Covers ...11 Connecting Outside (CO) Lines...11 Connecting Extensions ...12 Securing the Cables... 13 Closing Covers...14 Wall Mounting...15 2.6.1 Mounting on a Wooden Wall ... 15 2.6.2 Mounting on a Concrete or Mortar Wall ...16 Connecting Frame Earth ...17...

  • Page 9: Table Of Contents

    Before Installation Unpacking Check the package contents. Main Unit × 1 CD-ROM (including manuals, etc.) × 1 *AC Cord × 1 Mini Plug (for pager and music source) × 2 * The type of the AC cord may vary depending on the country/area of use. More than one type of AC cord may be included for countries/areas in Central and South America.

  • Page 10

    System Connection Diagram Outside (CO) Line Batteries Doorbell/Door Chime • Connect a display-equipped proprietary telephone (PT) to extension jack 01, as this extension is automatically designated as the manager extension. • For supported extension types, refer to "2.3 Connecting Extensions". Getting Started Remote PC Door Opener/...

  • Page 11

    Installation Opening Covers Pull the slide button to the right and, holding it, slide the cable cover upwards. Then turn the cable cover slightly to remove it. Connecting Outside (CO) Lines Insert the modular plugs of the telephone line cords (2-conductor wiring) into the outside (CO) line jacks.

  • Page 12

    Connecting Extensions Extension jacks can be used for proprietary telephones (PTs), Direct Station Selection (DSS) Consoles, single line telephones (SLTs), and Voice Processing Systems. Notes • Connect a display-equipped proprietary telephone (PT) to extension jack 01, as this extension is automatically designated as the manager extension. •...

  • Page 13

    Securing the Cables Attach the included strap to either of the 2 rails depending on your preference. Bind the cables as shown. Rail Rail Getting Started...

  • Page 14

    Closing Covers Attach the rear hooks on the cable cover to the main unit, then swing the cable cover closed so that the front hooks fit in place. Slide the cable cover down until it locks. Note For safety reasons, keep the front cover closed while the PBX is in operation. Getting Started Cable Cover...

  • Page 15: Wall Mounting, Mounting On A Wooden Wall

    Wall Mounting The PBX is designed for wall mounting only. The wall where the PBX is to be mounted must be able to support the weight of the PBX. When wall mounting the main unit, use either the included screws, or screws of the same size.

  • Page 16: Mounting On A Concrete Or Mortar Wall

    Notes • Do not block the openings of the cabinet. Leave at least 20 cm of space above and 10 cm to the sides of the PBX for ventilation. • Make sure that the wall behind the cabinet is flat and free of obstacles, so that the openings on the back of the cabinet will not be blocked.

  • Page 17: Connecting Frame Earth

    Affix the PBX to the screw heads. Notes • Do not block the openings of the cabinet. Leave at least 20 cm of space above and 10 cm to the sides of the PBX for ventilation. • Make sure that the wall behind the cabinet is flat and free of obstacles, so that the openings on the back of the cabinet will not be blocked.

  • Page 18

    • Be sure to comply with all applicable laws, regulations, and guidelines. • Proper earthing is very important to protect the PBX from external noise and to reduce the risk of electrocution in the event of a lightning strike. • The AC cable's earthing pin may not be enough to protect the PBX from external noise and lightning strikes.

  • Page 19: Starting The Advanced Hybrid System, Starting The Advanced Hybrid System

    Starting the Advanced Hybrid System Starting the Advanced Hybrid System This section explains the procedure for starting the PBX for the first time, with default values, or when you wish to re-initialise the PBX. Make sure that all outside (CO) lines you use are connected to the PBX. Set the Power Switch to the "OFF"...

  • Page 20

    CAUTION • The PBX is powered as long as the AC cord is plugged into an AC outlet, even if the Power Switch is set to the "OFF" position. • The power supply cord is used as the main disconnect device. Ensure that the AC outlet is located/installed near the equipment and is easily accessible.

  • Page 21: Pc Programming, Pc Programming

    PC Programming PC Programming PBX features and settings can be customised using a PC and the KX-TE308 Maintenance Console software. Customisation and maintenance can be done easily and efficiently using Windows-based PC programming software, with graphical icons to guide you. Programming can be performed both on-site, using a PC connected directly to the PBX, and off-site, by accessing the PBX via modem.

  • Page 22: Pt Programming, Programming Instructions

    PT Programming Programming Instructions The PBX can be programmed by entering 3-digit programming numbers with a PT. In this manual, how to programme some features through PT is explained. Required Telephone PBX settings can be customised through system programming by using a proprietary telephone (PT) with a display, such as the KX-T7730.

  • Page 23: Programming Procedures

    Fixed Button (KX-T7730/KX-T7735) Entering System Programming Mode To enter system programming mode, the system password is required. Note means default value throughout these programming instructions. Programming Procedures Notes • means default value throughout these programming instructions. • means to select "All" throughout these programming instructions. •...

  • Page 24

    The PT's dialling buttons can be used to enter characters when storing a name or message. The following tables depict the available characters: Table 1 (Alphabet mode)/Table 2 (Numeral mode) Getting Started...

  • Page 25

    Table 3 (Cyrillic alphabet mode for RU [Russia]/UA [Ukraine] model) * This character is only available for the KX-T7735RU. [Example of Entering Characters] To enter "Ann": (5 times) Notes • To toggle between "Alphabet mode" and "Numeral mode" or between "Alphabet mode", "Cyrillic alphabet mode (assignable only in Extension Name in Cyrillic [616] )", and "Numeral mode", press SELECT.

  • Page 26: Basic Features

    5.2.1 Basic Features Date & Time [000] ➞ SELECT (Sun … Sat) Notes • The clock starts immediately after the STORE button is pressed. • The PBX supports years from 2004 to 2099. System Speed Dialling Number [001] Note An Outside (CO) Line Access number (9/0 [for New Zealand: 1 or 9], 81 through 83) should be included before the phone number.

  • Page 27

    To avoid unauthorised access and possible fraudulent dialling, maintain the secrecy of the password. We strongly recommend that you change the default password value to something else for reasons of system security. It is best to use a password of 7 digits. Please change the password periodically.

  • Page 28

    System Speed Dialling Name [011] Note * A name can be stored using a PT's dialling buttons. The displayed character varies depending on the number of times that the dialling button is pressed. It is possible to toggle between "Alphabet mode" and "Numeral mode" by pressing SELECT. Automatic Line Access [121] Note * For New Zealand: 1 or 9...

  • Page 29

    Extension Name [604] Note * An extension name can be stored using a PT's dialling buttons. The displayed character varies depending on the number of times that the dialling button is pressed. It is possible to toggle between "Alphabet mode" and "Numeral mode" by pressing SELECT. Extension Name in Cyrillic [616] Notes •...

  • Page 30: Toll Restriction (trs) Features

    5.2.2 Toll Restriction (TRS) Features Toll Restriction (TRS) can prohibit certain extension users from making unauthorised outside (CO) line calls. Every extension is assigned to one of 5 classes of service (COSs) for each time service mode (TRS-COS—Day/Night/Lunch [601-603]); COS 1 grants the highest level of authorisation, allowing all outside (CO) line calls to be made, and COS 5 grants the lowest level of authorisation.

  • Page 31

    TRS—COS 2-5 Denied Code [302-305] NEXT (02 … 05) 02: for Class 2 03: for Class 3 04: for Class 4 05: for Class 5 TRS—Exception Code [306] NEXT PREV code no. phone no. (01 … 20) Max. 11 digits (0 …...

  • Page 32

    Getting Started...

  • Page 33

    Getting Started...

  • Page 34

    Getting Started...

  • Page 35

    120 mm Install a screw here. TEMPLATE FOR WALL MOUNTING Copy or print this template and place it on the wall. Install the screws as marked. If you mount the main unit on a concrete or mortar wall, fit anchor plugs (not included) into the wall beforehand. Hook the unit onto the screw heads.

  • Page 36

    Copyright: This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd. © 2005 Panasonic Communications Co., Ltd. All Rights Reserved.

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: