Section 1 - Quick Set-Up Quick Set-Up: Receiver; Quick Set-Up: Transmitter; Section 2 - System Description; Quick Set-Up: System Operation - Electro-Voice RE-2 Operating Instructions Manual

Section 1 - Quick Set-Up
Quick Set-up: Receiver
1. Do not connect the receiver to any other
equipment yet.
2. Connect the two antennas to the receiver.
3. Plug the power supply into the back of the
receiver and into an outlet
4. Press the POWER switch. Display will light up.
5. Press and hold the SET button until ClearScan
shows and starts flashing on the right side
of the screen.
6. When ClearScan stops flashing, the receiver will
automatically set itself and display the clearest
group and channel.
7. If you are using a guitar, turn off the receiver.
Press and hold SET while you turn the receiver on.
A guitar symbol will appear in the display to
indicate instrument mode.
8. Turn the receiver off and connect the mixer or
other audio system to the receiver XLR Connector
or the ? inch Line Level Jack.
9. Set the audio mixer or other system input level to
minimum.
10. Press the Power switch button in again.
Receiver "Quick Set-up" is complete.

Quick set-up: Transmitter

1. With the Power Switch on the transmitter OFF,
install a fresh alkaline battery into the transmitter.
2. Place the transmitter Power Switch to the
ON position.
3. The Red Battery Low Light near the display will
flash on and then off. The display will also come
on and display a group and channel.

Section 2 - System Description

The RE-2 Wireless Microphone system combines
frequency agility and ease of use like no other. The
RE-2 transmitters and receivers operate over a 24
MHz band width in the UHF portion of the Radio
Frequency spectrum.
System Features Include:
• Advanced ClearScan technology for selecting the
clearest available channels in intermodulation free
g r o u p s .
• Completely programmable in 25 kHz steps for over
950 possible frequencies.
• LCD Displays for ease of viewing-Group, Channel,
Frequency, Battery Status, Diversity Activity, Audio
Meter and RF Meter.
• Patented Phase Diversity System
• Adjustable Unbalanced Line Level 1/4 inch output jack
• Balanced XLR output jack for fixed Microphone
Level or adjustable Line Level
4. Press the SET button once and the Group number
will flash.
5. Use the up and down arrows to change the Group
number to match the Group number displayed on
the receiver. Press SET and the Channel Number
will flash.
6. Use the up and down arrow buttons to change the
Channel to match the receiver. Press Set and
nothing will be flashing. The channel is now set.
TM
7. If you are using a bodypack transmitter, plug the
microphone into the transmitter connector. If using a
g u i t a r, turn the transmitter off and wait until display
is blank. Hold SET down and turn the transmitter
on. A guitar symbol should appear on the display.
Plug the cord into the transmitter and guitar.
Transmitter "Quick Set-up" is complete.

Quick set-up: System Operation

1. With the transmitter and receiver on, monitor the
display screen. Note that the RF (1-100) Bar graph
should indicate near the 100 mark. The AF Bar
should show very little, if any, indication until you
talk or sing into the microphone. While talking or
singing in the loudest voice used in performance,
adjust the transmitter gain control if necessary to
cause the AF Bar Graph to peak near -6 to -3 but
not over +3 for best performance.
2. Set the mixer/amp gain.
3. Talk or sing into the microphone or play the guitar
at a normal volume. You should hear audio
coming out of the system.
4. If using the unbalanced 1/4" output, you may have
to adjust the gain (via the control next to the
connector on the back panel) to match the level
found when singing or playing with a wired
connection.
"Quick Set-up" is now complete.
Please enjoy your RE-2 system.
The high quality audio circuitry and advanced Radio
Frequency (RF) signal processing offer broadcast
quality signal-to-noise and audio clarity.
• Front Panel Power ON/OFF Switch
• Front Panel Software Control of Squelch settings
• Double Squelch (Amplitude and Tone) system
prevents false squelch
• Lock out feature to prevent accidental
channel changes
• "Smart" battery feature in the transmitter means
there is no wrong orientation
• Power Lock On feature prevents accidental turn off
• Battery level displayed at the receiver
- -
1
English