Manually Programming Timer Recordings - Panasonic SC-HT1000 Operation Manual

Recordable dvd home theater system
Hide thumbs Also See for SC-HT1000:
Table of Contents

Advertisement

Manually programming timer
recordings
1
Press [PROG/CHECK].
TIMER
Remain
RECORDING
12:56:00
No. Name
Date
Start
Stop
Mode
01
BBC 1 15/ 7 TUE
19:00
20:00
SP
New Timer Programme
SELECT
Press ENTER to store
new programme.
ENTER
RETURN
2
Press [3, 4] to select "New Timer
Programme" and press [ENTER].
3
Press [1] to move through the items
and change the items with [3, 4].
≥The current settings are shown each time you press [1].
≥You may use the numbered buttons to enter the "Name",
"Date", "Start" and "Stop".
TIMER
Remain
RECORDING
12:57:00
Name
Date
Start
Stop
BBC 1
15/ 7 TUE
22:30
22:00
≥Name (Programme position/TV Station Name)
≥Date
[. Current date
l
;:
l Next day up to one month later minus one day
l
;:
l Weekly timer: SUN-SAT>MON-SAT>MON-FRI
l
;:
{. Daily timer: SUN>--->SAT
≥Start (Start time)/Stop (Finish time)
The time increases or decreases in 30-minute increments if
you hold the button.
≥Mode (Recording mode
XP!#SP!#LP!#EP!#FR
^"""""""""""""""""J
≥PDC ( right)
ON!)OFF (– – –)
≥Title ( page 40)
Select "Title" using [2, 1] and press [ENTER].
4
Press [ENTER] when you have
finished programming the timer.
TIMER
Remain
RECORDING
12:58:00
No. Name
Date
Start
Stop
Mode
01
BBC 1 15/ 7 TUE
19:00
20:00
SP
02
BBC 1 15/ 7 TUE
22:00
22:30
SP
New Timer Programme
Repeat steps 2–4 to programme other recordings.
5
Press [PROG/CHECK].
The timer recording list disappears.
6
Press [F TIMER].
The unit turns off output picture and sound from all terminals
(e.g. Scart AV and RF out terminals) and "F" lights on the
unit's display to indicate timer recording standby has been
activated.
1:58 SP
15.7. TUE
Disc
PDC
space
OFF
OK
1:58 SP
15.7 . TUE
Mode
PDC
SP
OFF
Title
page 25)
1:58 SP
15.7. TUE
Disc
PDC
Displayed if the recording
space
OFF
OK
can fit in the remaining
OFF
OK
space on the disc.
∫ To release the unit from recording standby
If you want to record something else before the programme start
time, for example:
Press [F TIMER].
The unit turns on and "F" goes out.
≥Be sure to press [F TIMER] before the programme start time to
put the unit on recording standby. Timer recording will work only
if "F" is displayed.
∫ To cancel recording when recording has
already begun
Press [F TIMER].
Recording stops.
[Note]
≥The built-in clock employs 24-hour system.
≥If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording
starting time, the "F" flashes on the unit display. In this case,
press [F TIMER] to put the unit in the timer recording standby
mode.
≥"F" flashes when the unit cannot go to timer recording standby
(e.g., a disc isn't loaded, a disc that can't be recorded to is
loaded, or the disc is protected). Check the disc carefully.
≥Even if the unit is put in the timer recording standby mode or the
timer recording is being performed, you can play a programme.
≥The actual time recorded may be longer than the programme
itself when television programmes are recorded using VIDEO
Plus+.
≥"PROG FULL" is displayed if there are already 16 programmes.
≥The remaining time displayed is based on the current recording
mode.
≥When you programme successive timer recordings to start
immediately one after the other, the unit cannot record the part
at the beginning of the later programmes (a few seconds when
recording with DVD-RAM and approximately 30 seconds when
recording with DVD-R).
∫ Setting for control of the recording starting
and ending time by special signal included in
the broadcasting signal (PDC Function)
PDC stands for Programme Delivery Control.
If a TV programme, for example a football game runs longer than
scheduled, is shortened or starts earlier or later, this function
synchronizes the recording start and stop with the actual
broadcasting start and stop of the TV programme.
Conditions for correct operation of the PDC function:
≥"ON" must be selected under "PDC" on the display.
≥The TV station must broadcast PDC signals.
≥The programme starting time must be set correctly to the
starting time listed in the newspaper/magazine.
27

Advertisement

Table of Contents
loading

Table of Contents