Group Call - Icom IC-M802 Instruction Manual

7
CALL PROCEDURE

■ Group call

When you use DSC for calling the desired ship's group,
use "Group" menu.
q Push [MODE
set
w Rotate [CH] to select "Group" then push [ENT].
e Select the desired 9-digit group code, then push
[ENT].
• Use [CH] to select the group code when the desired
group is pre-programmed.
* * * * * * * * * G r o u p * * * * * * * *
- - - - - - - G r o u p I D - - - - - - -
M a n u a l s e t
Ç
G r o u p - 1
G r o u p - 2
G r o u p - 3
G r o u p - 4
G r o u p - 5
S E L
• When "Manual set" is selected, enter the desired
code (last 8 digits only) using the keypad.
- The first digit "0 (zero)" is fixed for group code.
* * * * * * * * * G r o u p * * * * * * * *
- - - - - - - G r o u p I D - - - - - - -
r Rotate [CH] to select the desired pre-programmed
traffic frequency, or "Manual set" then push
[ENT].
✔ When the pre-programmed traffic frequency is
selected, go to step y.
* * * * * * * * * G r o u p * * * * * * * *
- - T r a f f i c f r e q u e n c y - - -
M a n u a l s e t
Ç
T : 4 5 6 7 . 0 k H z I C - M 8 0 2 - 1
R : 4 5 6 7 . 0 k H z
T : 1 2 3 4 5 . 0 k H z I C - M 8 0 2 - 2
R : 1 2 3 4 5 . 0 kHz
S E L
t Enter the desired transmit and receive traffic fre-
quency using the keypad, then push [ENT].
• One of the voice channel, such as Tx/Rx: 2082.5 kHz,
4146.0 kHz, should be used.
* * * * * * * * * G r o u p * * * * * * * *
- - T r a f f i c f r e q u e n c y - - -
T X : _ 2 1 3 4 . 0 k H z
R X : _ 2 1 3 4 . 0 k H z
S E L
36
] to select the DSC menu.
0 2 3 4 5 6 7 8 9
0 2 3 4 5 6 7 8 8
0 2 3 4 5 6 7 8 7
0 2 3 4 5 6 7 8 6
0 2 3 4 5 6 7 8 5
O K
0 8 7 6 5 4 3 2 1
O K
O K
O K
y Rotate [CH] to select the desired pre-programmed
calling frequency, or "Manual set" then push
[ENT].
✔ When the pre-programmed call frequency is se-
lected, go to step i.
* * * * * * * * * G r o u p * * * * * * * *
- - - - C a l l f r e q u e n c y - - - -
M a n u a l s e t
Ç
T : 2 3 4 5 . 0 k H z I C - M 8 0 2 - 1
R : 2 3 4 5 . 0 k H z
T : 2 1 7 7 . 0 k H z S H I P
R : 2 1 7 7 . 0 k H z
S E L O K
u Enter the desired transmit and receive call fre-
quency using the keypad, then push [ENT].
* * * * * * * * * G r o u p * * * * * * * *
- - - - C a l l f r e q u e n c y - - - -
T X : _ 2 3 4 5 . 0 k H z
R X : _ 2 3 4 5 . 0 k H z
S E L O K
i The calling stand-by screen is displayed as fol-
lows. Verify the calling information then hold down
[CANCEL/CALL] for 1 second to transmit the group
call.
• Hold down [ENT] for 1 second to store the calling infor-
mation into TX memory described in pages 23 and 45,
if desired.
* * * * * * * * * G r o u p * * * * * * * *
- - - - - - - - - C a l l - - - - - - - - -
T o : 0 8 7 6 5 4 3 2 1
T r a f f i c : R a d i o t e l e p h o n e
T X
R X
C a l l F r e q : T X
R X
C a l l
o After sending the call, the traffic frequency is se-
lected automatically.
< T r a f f i c >
R X
G P S
S P
E x i t
!0 Announce the following message to stations.
- "The group name."
- "This is ..... (your ship name)."
- The 9-digit identity OR call sign (or other identifi-
cation of the ship).
2 1 3 4 . 0 k H z
2 1 3 4 . 0 k H z
2 1 7 7 . 0 k H z
2 1 7 7 . 0 k H z
W r i t e - M e n u
J 3 E
L a t 3 4 3 4 ' N
L o n 1 3 5 3 4 ' E
1 2 : 3 4