Icom IC-M802 Instruction Manual page 30

7
CALL PROCEDURE
D Distress call to ships
q Push [DSC] to select the DSC watch mode.
w Push [MODE
set
[DSC]
[CANCEL/CALL]
e Rotate [CH] to select "Individual," then push
[ENT].
r Rotate [CH] to select "Distress," then push
[ENT].
* * * * * * I n d i v i d u a l * * * * * *
- - - - - - - C a t e g o r y - - - - - - -
R o u t i n e
S a f e t y
U r g e n c y
D i s t r e s s
Ç
S E L
t Rotate [CH] to select the desired preprogrammed
ID, or "Manual set," then push [ENT].
✔ When preprogrammed ID is selected, go to
step u.
* * * * * * I n d i v i d u a l * * * * * *
- - - - - - A d d r e s s I D - - - - - -
M a n u a l s e t
Ç
I C - M 8 0 2 - 1
I C - M 8 0 2 - 2
I C - M 8 0 2 - 3
I C - M 8 0 2 - 4
I C - M 8 0 2 - 5
S E L
y Enter the desired 9-digit MMSI code using the key-
pad.
✔ The number "0 (zero)" cannot be entered as the 1st
digit, since the 1st digit "0" means a group code.
* * * * * * I n d i v i d u a l * * * * * *
- - - - - - A d d r e s s I D - - - - - -
22
] to select the DSC menu.
[MODE ] [ENT]
SET
[CH] [F] [FREQ/CH]
O K
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 8
1 2 3 4 5 6 7 8 7
1 2 3 4 5 6 7 8 6
1 2 3 4 5 6 7 8 5
O K
9 8 7 6 5 4 3 2 1
O K
u Rotate [CH] to select the desired preprogrammed
traffic frequency, or "Manual set" then push
[ENT].
✔ When preprogrammed traffic frequency is se-
lected, go to step o.
* * * * * * I n d i v i d u a l * * * * * *
- - T r a f f i c f r e q u e n c y - - -
M a n u a l s e t
Ç
T : 4 5 6 7 . 0 k H z I C - M 8 0 2 - 1
R : 4 5 6 7 . 0 k H z
T : 1 2 3 4 5 . 0 k H z I C - M 8 0 2 - 2
R : 1 2 3 4 5 . 0 k H z
S E L O K
i Enter the desired transmit and receive traffic fre-
quency using the keypad, then push [ENT].
* * * * * * I n d i v i d u a l * * * * * *
- - T r a f f i c f r e q u e n c y - - -
T X : _ 2 1 3 4 . 0 k H z
R X : _ 2 1 3 4 . 0 k H z
S E L O K
o Rotate [CH] to select the desired calling frequency,
then push [ENT].
* * * * * * I n d i v i d u a l * * * * * *
- - - - C a l l f r e q u e n c y - - - -
2 1 8 7 . 5 k H z
Ç
4 2 0 7 . 5 k H z
6 3 1 2 . 0 k H z
8 4 1 4 . 5 k H z
1 2 5 7 7 . 0 k H z
1 6 8 0 4 . 5 k H z
S E L O K
!0 The call stand-by screen is displayed as follows.
Verify the calling information then hold down [CAN-
CEL/CALL] for 1 second to start calling.
* * * * * * I n d i v i d u a l * * * * * *
--------- C a l l ---------
C a t e g o r y : D i s t r e s s
T o : 9 8 7 6 5 4 3 2 1
T r a f f i c : R a d i o t e l e p h o n e
T X
R X
C a l l f r e q : T X
R X
C a l l
!1 After the call, wait for an acknowledgement call.
• The calling is made only one time.
I n d i v i d u a l
< W a i t f o r A C K >
R X
G P S
S P
E x i t
2 1 3 4 . 0 k H z
2 1 3 4 . 0 k H z
2 1 8 7 . 5 k H z
2 1 8 7 . 5 k H z
W r i t e - M e n u
J 2 B
L a t 3 4 3 4 ' N
L o n 1 3 5 3 4 ' E
1 2 : 3 4