Page 2
Long tests and thorough system development have made it possible to achieve the highest sound quality. The MCS II system can only be assembled on Nolan helmets pre-set for N-Com. The MCS II system allows you to listen to audio devices installed motorcycles;...
2. CONTENTS OF THE PACKAGING ........7 3. INSTALLING THE MCS II SYSTEM ......... 8 3.1. Removing the MCS II system from the helmet ....13 4. OPERATION OF THE MCS II SYSTEM ......14 5. MAINTENANCE............14 6. LIMITED WARRANTY ..........15 6.1.
Caution: The product cannot be used in official or unofficial competitions, motordromes, circuits, racing tracks and the like. Caution: Installation of the MCS II system results in a weight increase of approximately 70g, which is added to the weight of the helmet and of the other accessories.
Page 5
N-Com system must be carried out with the vehicle stopped. In all cases, obey the Traffic Regulations and remember that riding your motorcycle has absolute priority over any other manoeuvre. Adjust the volume to a level that does not disturb or distract you while riding and at the same time allows you to distinctly heal background noises.
Use the device in the normal position only, as described in the product documentation. Do not attempt to disassemble, tamper with or modify any part of the N-Com system. Only qualified personnel can carry out technical assistance on this product.
3. INSTALLING THE MCS II SYSTEM Remove the cheek padding (see helmet instructions). Remove the helmet edge gasket using the special tool (Fig. 1). Remove “N-Com” plug found at the back of the shell gasket (Fig. 1).
Page 9
Option 1: remove the bottom element in foam material and the filling materials in the housings of the N-Com earpieces located in the EPS cheek pads. Option 2: remove the left and right side filling material as well as the filling material in the housings of the N-Com earpieces located in the EPS cheek pads.
Page 10
Place the system in the special housing in the back of the helmet, pushing it all the way into the groove (Fig. 3). Fig. 3 Fix the cable inside the helmet and make sure the right fixing clip snaps into its housing (Fig. Fig.
Page 11
(Fig. Caution: make sure that the side of the microphone support with the writing “N-Com” is facing inward. Fig. 5 Position the left and right speakers in the respective housing obtained in ...
Page 12
Use of the extension cable (optional) In case of need, it is possible to use the Extension Cable included in the package to make the connection via cable to the motorcycle easier, moving forward the micro USB connector on the left side of the helmet. Remove the protective film and ...
Fig. 8 3.1. Removing the MCS II system from the helmet Proceed as follows to remove the MCS II system from the helmet: Remove the cheek padding and the shell gasket; Unhook the right clip from the ...
4. OPERATION OF THE MCS II SYSTEM Hook up the cable to the motorcycle, then to the MCS II system. The audio of the system installed on the motorcycle is now transferred to the helmet. You can use the interphone system on the motorcycle by connecting both the pilot’s helmet and the passenger’s to the motorcycle.
Negligence and normal wear of internal and external parts. Any damage caused by an accident; Any change or modification made to the helmet or to the N-com system by the user or by third parties. Color changes or damages caused by exposure to harmful chemical products.
Nolangroup. Tampering with the internal electronic card or with other parts of the N-Com system shall invalidate the warranty. Moreover, the defects covered by this warranty do not include all those specific and subjective situations that may come up during the active use of the helmet such as, for example, comfort problems while riding or aerodynamic noises.
Name and stamp of the authorized dealer. Product purchase date. Buyer’s name and address. Nolangroup reserves itself the right to not carry out repairs under warranty if the aforementioned information is removed or modified after the original purchase of the product from the dealer.
Legislative Decree 2 February 2002 n. 24 6.5. Product identification N-Com products are identified by means of a code that allows product traceability and identification. The identification code is found underneath the bar code printed on the product packaging.
WARRANTY REGISTRATION FORM Product name: MCS II v.04 Identification code Buyer’s Information Name Last name Address Phone e-mail Dealer’s stamp Date of purchase...
Page 20
MCS II v.04 - 07/03/2016 16:34:00 Printed on recycled paper.