1. Manuals
  2. Brands
  3. N-Com Manuals
  4. Conference System
  5. MCS II
  6. Instruction manual

N-Com MCS II Instruction Manual

Motorcycle communication system
Hide thumbs Also See for MCS II:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instructions for Use Manual
SAFETY AND INSTRUCTIONS FOR USE

Advertisement

Table of Contents
loading

Related Manuals for N-Com MCS II

Summary of Contents for N-Com MCS II

  • Page 1 SAFETY AND INSTRUCTIONS FOR USE...
  • Page 2 Long tests and thorough system development have made it possible to achieve the highest sound quality. The MCS II system can only be assembled on Nolan helmets pre-set for N-Com. The MCS II system allows you to listen to audio devices installed motorcycles;...

  • Page 3: Table Of Contents

    1.2. Appropriate use ............4 1.3. Disposal ..............6 2. CONTENTS OF THE PACKAGING ........7 3. INSTALLING THE MCS II SYSTEM ......... 8 3.1. Installing the microphone..........11 3.2. Installing the Basic Kit2 MCS on the helmet.....13 4. REMOVING THE MCS II SYSTEM........18 5.

  • Page 4: Warnings And Safety

    Consequently, make sure the inside of the helmet, including the comfort padding, does not get wet in order to avoid damage to the system. If it does, remove the N-Com system and comfort padding and let it air dry.
  • Page 5 Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it before you use it on the road. Caution: Adjusting the volume to very high levels may cause damage to...

  • Page 6: Disposal

     Only qualified personnel can carry out technical assistance on this product. In case of any malfunction, always turn to your local dealer. The helmet is a safety device. Tampering with it and/or with the electronic system inside the helmet can lead to dangerous situations, in addition to invalidating the product warranty.

  • Page 7: Contents Of The Packaging

    2. CONTENTS OF THE PACKAGING Basic Kit2 MCS Removable Microphone Honda Goldwing connection cable Harley Davidson connection cable Clamp Microphone-Stop Washer and screw Adhesive Velcro pads Microphone securing stickers...

  • Page 8: Installing The Mcs Ii System

    3. INSTALLING THE MCS II SYSTEM Fig. 1 Fig. 2  Remove the “N-Com” protection plate located on the helmet shell (Fig. 1) and open the helmet chin guard (flip up helmets).  Remove the right and left cheek pads from the helmet (see...
  • Page 9 (Fig. 4).  Temporarily put the padding on the outside of the helmet (Fig. 5).  Remove the N-Com cover from the helmet border gasket. Push from inside of the helmet facilitate the removal (Fig.
  • Page 10 ONLY FOR FULL-FACE HELMETS Remove the chin guard by  pulling on the special red tab. Fig. 7  Remove right left polystyrene cheek pads gently pulling them out of the helmet. The helmet shell can be opened slightly to facilitate the removal of the cheek pad .

  • Page 11: Installing The Microphone

    3.1. Installing the microphone JET HELMETS OR FLIP-UP HELMETS Fig. 9 Fig. 10  Prepare the microphone by inserting the microphone clamp, being careful to position it properly (Fig. 9) Note: the flat part of the clamp must be facing upward when the microphone is positioned as shown in figure 10.
  • Page 12 FULL-FACE HELMETS Take the polystyrene cheek pad  (left-hand side) and position the microphone in its housing, as shown in fig. 13, making sure that the fluorescent band stays facing the inside of the helmet. (Fig. 14) Fig. 13 Secure the microphone to the ...

  • Page 13: Installing The Basic Kit2 Mcs On The Helmet

    Installing the Basic Kit2 MCS on the helmet Fig. 15  Position the Basic Kit2 MCS inside the helmet as shown in figure 15, next to the N-Com housing in the shell.  Looking at the helmet from the outside, slide the rear positioning tab into groove A as shown in the figure;...
  • Page 14  Pull out the connectors area from the helmet gasket: the gasket will have to be slightly deformed to facilitate the insertion. Fig. 17 Fig. 18 Fig. 19 Insert the microphone connector in the Basic Kit2 MCS.  Before you place the speaker in its housing, apply the Velcro pad to the ...
  • Page 15 Position loudspeaker in  special housing obtained polystyrene cheek pad (Fig. 20). Fig. 20  Replace the polystyrene cheek pad (left side), positioning the cable in the groove that you see in the cheek pad (Fig. 20). Note: Make sure the cheek pad is properly positioned housing,...
  • Page 16 ONLY FOR FULL-FACE HELMETS Insert the chin guard (microphone side), gently placing the microphone in its housing. Then press down on the red tab until the chin guard is locked in place on the helmet. (Fig. Fig 22 Fig. 23 Fig.
  • Page 17 Caution: Always verify the proper length of the chinstrap and adjust it as necessary, once again referring to the specific helmet instructions.  Reposition protection plate covering the “N-Com” housing on the shell. First insert the rear part and then press the front part until the fastening clasp clicks.

  • Page 18: Removing The Mcs Ii System

    5. OPERATION OF THE MCS II SYSTEM Hook up the connection cable to the Harley Davidson / Honda Goldwing, then to the MCS II system. The audio of the system installed on the motorcycle is now transferred to the helmet.

  • Page 19: Maintenance

    6. MAINTENANCE The N-Com does not require any special maintenance tasks. In case you use the kit when it rains, dry off the wet parts of the helmet, paying special attention to the contact area.

  • Page 20: Warranty Coverage

    Negligence and normal wear of internal and external parts. Any damage caused by an accident; Any change or modification made to the helmet or to the N-com system by the user or by third parties. Color changes or damages caused by exposure to harmful chemical products.

  • Page 21: Validity Of This Limited Warranty

    Nolangroup shall not be responsible in case the product presents limited capabilities due to the operating mode of cell phones or of other accessories or equipment not supplied by Nolangroup. Tampering with the internal electronic card or with other parts of the N-Com system shall invalidate the warranty.

  • Page 22: Product Identification

    Legislative Decree 2 February 2002 n. 24 7.5. Product identification N-Com products are identified by means of a code that allows product traceability and identification. The identification code is found underneath the bar code printed on the product packaging.

  • Page 23: Warranty Registration Form

    8. WARRANTY REGISTRATION FORM Product name: MCS II v.03 Identification code Buyer’s Information Name Last name Address Phone e-mail Dealer’s stamp Date of purchase...
  • Page 24 MCS II v.03 - 19/12/2012 09:55:00 Printed on recycled paper.

Table of Contents