NAD C375BEE Owner's Manual
  1. Manuals
  2. Brands
  3. NAD Manuals
  4. Amplifier
  5. C375BEE
  6. Owner's manual

NAD C375BEE Owner's Manual

Stereo integrated amplifier
Hide thumbs Also See for C375BEE:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
C 375BEE
®
Stereo Integrated Ampli er
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for NAD C375BEE

Summary of Contents for NAD C375BEE

  • Page 1 C 375BEE ® Stereo Integrated Ampli er Owner’s Manual...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS FOR LATER USE. 14 Outdoor Antenna Grounding - If an outside antenna or cable system FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE is connected to the product, be sure the antenna or cable system is AUDIO EQUIPMENT.
  • Page 3 Changes or modi cations to this equipment not expressly approved by FCC NOTICE NAD Electronics for compliance could void the user’s authority to operate This equipment has been tested and found to comply with the limits for a this equipment.
  • Page 4 Your local administrative o ce can advise you of the responsible waste disposal point. NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited Copyright 2008, NAD Electronics International, a division of Lenbrook Industries Limited...

  • Page 5: Getting Started

    If the unit is not going to be used for some time, disconnect the plug from the AC socket. Should water get into your NAD C 375BEE, shut o the power to the unit and remove the plug from the AC socket. Have the unit inspected by a quali ed service technician before attempting to use it again.

  • Page 6: Identification Of Controls

    IDENTIFICATION OF CONTROLS FRONT PANEL 1 STANDBY: With the rear panel POWER switch set to ON position, 5 SOFT CLIPPING INDICATOR: The blue SOFT CLIPPING LED shows press this button to switch ON the C 375BEE from standby mode. that the SOFT CLIPPING mode is engaged. Refer also to the item below The Standby LED indicator will turn from amber to blue.
  • Page 7 11 TONE CONTROLS: The NAD C 375BEE is tted with BASS and TREBLE tone controls to adjust the tonal balance of your system. The 12 o’clock MP (MEDIA PLAYER): Selects a line-level source connected to the MP position is “...

  • Page 8: Rear Panel

    TAPE TO TAPE COPYING Mini Disc player or the output signal from a step-up ampli er for a You can copy between two tape machines connected to your NAD turntable. Use a twin RCA-to-RCA lead to connect the auxiliary unit’s left C 375BEE.

  • Page 9: Power Drive

    In normal use, this should be connected to switch to “OFF” position for normal stereo listening. the Main In sockets with the links supplied. To connect your NAD C 375BEE to external processor or ampli er sections, remove rst these links. Use a NOTE twin RCA-to-RCA lead to connect the left and right “Audio Input”...

  • Page 10: Important Notice

    NAD’ s proprietary PC software or other compatible external controllers. must not exceed 100 watts. NAD is a certi ed partner of AMX and Crestron and fully supports these 25 FUSE HOLDER: In the unlikely event a fuse may need to be replaced, external devices.
  • Page 11 USING THE SR 8 REMOTE CONTROL The SR 8 remote control handset handles the key functions of the C 375BEE as well as other NAD Stereo Receivers, Integrated Ampli ers and Preampli ers. It has additional controls to remotely operate NAD CD Players, AM/FM Tuners and dedicated AM/FM/DAB Tuners.
  • Page 12 10 TONE DFT : Tone Controls are enabled or disabled by pressing this button. CD PLAYER CONTROL (for use with NAD CD Player): Set the DEVICE SELECTOR to “CD” in order to gain access to these buttons. Some of the control buttons below are applicable only to speci c NAD CD Player models;...

  • Page 13: Troubleshooting

    REFERENCE TROUBLESHOOTING CONDITION POSSIBLE CAUSES POSSIBLE SOLUTIONS No sound. • Power AC lead unplugged or power not • Check if AC lead is plugged in and power switched ON. switched ON. • Tape Monitor selected. • De-select Tape Monitor mode. •...

  • Page 14: Specifications

    REFERENCE SPECIFICATIONS PREAMPLIFIER SECTION LINE LEVEL INPUT, PRE OUT THD (2 Vin 2 Vout, CCIF IMD, DIM 100) >0.004 % (ref. 20 Hz – 20 kHz) Signal/Noise ratio IHF >102 dB (A-weighted, ref. 500 mV) >110 dB (A-weighted, ref. 2V, Volume maximum) >92 dB (A-weighted, ref.

  • Page 15: Overall Specifications

    REFERENCE SPECIFICATIONS OVERALL SPECIFICATIONS CD IN, SPEAKER OUT THD (250 mW to rated power, CCIF IMD, DIM 100) <0.009 % (ref. 20 Hz - 20 kHz) Signal/Noise ratio >94 dB (A-weighted, ref. 1 W) >113 dB (A-weighted, ref. 150 W, volume set for 2V input) Frequency response ±...
  • Page 16 ©2008 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International C 375BEE Owner’s Manual Issue 1-10/08...

Table of Contents