Table of Contents
Advertisement
Setup menus (continued)
USER menu <OPERATION>
No./Item
114
This selects whether to cause the REC
INH lamp to flash or light up when the
cassette has been set to the accidental
REC INH
erasure prevention status.
LAMP
0000
LIGHT : The lamp lights up.
0001 FLASH : The lamp flashes.
Note:
When the REC INHIBIT switch is set to
ON, the REC INH lamp always lights
regardless of the general setting status.
115
This selects whether to enable or
disable the operation of the EJECT
button on the front panel.
EJECT SW
INH
0000
Operation is disabled while the unit is
in the recording mode.
0001
Operation is enabled in all modes.
120
This selects the modes for the picture
and sound output when the tape is
ejected.
EJECT EE SEL
0000
0001 BLACK :
The picture turns black, and the sound
is muted.
0002 GRAY :
The picture turns gray, and the sound
is muted.
Note:
The IEEE1394 digital output video will be
black even if GRAY is selected.
121
This selects whether the EE mode or
playback mode is to be established
during fast forwarding or rewinding.
F/R EE SEL
0000
0001
TAPE : Playback mode
122
This select whether the EE mode or
playback mode is to be established
when operation is stopped.
STOP EE SEL
0000
0001
TAPE : Playback mode
Note:
The selection is complied with even in the
standby OFF mode. However, the picture
will turn gray (black for IEEE1394 digital
output) when TAPE is selected.
The underlined items indicates the initial setting.
24
Description
REC :
OFF :
EE : EE mode
EE : EE mode
EE : EE mode
No./Item
160
This sets the repeat play mode.
0000
MEMORY
No repeat play (normal operation)
MODE
0001 M-STOP :
The tape stops near the BEGIN point when a
FF or REW operation has been performed.
0002 REPT1 :
During playback, the tape is rewound
to the BEGIN point and stopped when
the END point is reached.
0003
CONT :
During playback, the tape is rewound
to the BEGIN point and then played,
and these steps are repeated when
the END point is reached.
161
This sets the BEGIN point in the repeat
play mode.
CTL BGN
Whether TC or CTL is displayed on the counter
or
when the COUNTER button is pressed is set
TC BGN
here. When there is no setting, --:--:--:-- appears,
and the tape start serves as the BEGIN point.
162
This sets the END point in the repeat
play mode.
END
Whether TC or CTL is displayed on the counter
when the COUNTER button is pressed is set
here. When there is no setting, --:--:--:-- appears,
and the tape end serves as the END point.
163
This sets the output image when the
tape returns to the BEGIN point in the
repeat play mode.
REPT MODE
0000 FREEZE :
The tape returns to the BEGIN point
while the playback image at the END
point remains frozen.
0001 BLACK :
The tape returns to the BEGIN point while
a BLACK picture remains on the screen.
0002 EE_SEL :
The tape returns to the BEGIN point
with an image which is in compliance
with the setup menu item No.121 (F/R
EE SEL) setting.
Note:
If, when FREEZE has been selected, the
END point has been set at the tape end,
the playback image will not be frozen
properly. Set the END point in a range
where pictures have been recorded.
USER menu <INTERFACE>
No./Item
202
This sets the ID information to be
returned to the controller.
ID SEL
0000
OTHER :
0001 DVCPRO :
0002
Notes:
• ID information of any VTR except for the
DVCPRO's is set in OTHER.
• The ORIG setting should only be used
when a Panasonic controller (AG-A850
etc. sold separately) is connected.
Description
OFF :
Description
ORIG :
Hide quick links:
Advertisement
Table of Contents
