JUKI LZ-2290A Series Manual page 26

●
In elastic tape attaching or counter stitching processes for girdles, shorts or swimwear, the
machine promises easy handling of the material. The material is placed over the cylinder-
bed and can be sewn at once without stopping the sewing machine during sewing.
This dramatically increases productivity.
●
For a flat-bed sewing machine, a tubular sewing product is only sewn by rotating it on the
bed. However, for this cylinder-bed machine, the material is placed over the bed to enable
handling to take place under the bed. Sewing troubles such as diagonal creases or uneven
material feed that are likely to occur on a flat-bed machine due to poor operability can be
reduced on this cylinder-bed machine.
●
The cylinder-bed shape is designed to promise easier sewing of wider tape whose width is
up to 50mm. The machine that is equipped with this type of bed can be used for attaching
lace to the bottom of a girdle.
●
Changeover between the standard and 3-step zigzag stitching patterns can be achieved
using the lever located between the machine arm and needle. This means that sewing
machine changing, according to the type of zigzag stitches, is no longer required, thereby
increasing the facility operation rate. In addition, the machine promises higher cost-
effectiveness since use of the machine reduces investment costs.
●
The machine comes with a new feed mechanism that is designed to reduce play and
deflection. It helps promise highly consistent sewing performance even at a maximum
sewing speed of 5,000rpm (standard zigzag stitch of which the zigzag width is 5mm or less).
Thanks to the feed mechanism, the machine demonstrates an increased productivity in
processes in which a higher sewing speed is required, such as elastic tape attaching processes.
●
The table stand specifically designed for the cylinder-bed has been improved in both
strength and rigidity. The pedal location is straight below the center of the needle entry.
This allows the operator to carry out sewing work in a comfortable posture.
●
Gauges such as a throat plate and presser foot, hooks, bobbins, and bobbin cases, as well
as other attachments and devices of the conventional machines can be used with this zigzag
stitching machine.
●
WHEN YOU PLACE ORDERS
Please note when placing orders, that the model name should be written as follows:
LZ2284C7
Wiper and automatic reverse feed function
Automatic reverse
Wiper
feed function
Not provided Provided
Provided Provided
● PSC box
Control box Code
Standard
SC910 S
PSC box
＊
For JUS (LA) Single-phase
＊
For JUS , General Export 3-phase
For General Export Single-phase
For EU (CE) Single-phase
For China Single-phase
＊ JUS: North America and Central and South America.
● Motor for SC
M91S
Pulley belt Code
Standard S
● To order, please contact your nearest JUKI distributor.
MARKETING & SALES H.Q.
✽ Specifications and appearance are subject to change without prior notice for improvement.
✽ Read the instruction manual before putting the machine into service to ensure safety.
✽ This catalog is printed on recycle paper.
Auto-lifter Code
Not provided ZZ
Code
AK83 (pedal-driven) AK
0B
WB
S
Code
100∼120V PFL S
200∼240V PFL D
200∼240V PFL K
200∼240V PFL N
200∼240V PFL U
● Operation panel
Operation panel Code
IP-100B IP100B
CP-160B CP160B
8 2 1
- - , KOKURYO-CHO, CHOFU-SHI,
TOKYO 182 - 8655 , JAPAN
PHONE : ( 81 ) 3 3480 2357
- - ,
FAX : ( 81 ) 3 3430 4909 4914
- - ,
http://www.juki.com
●
SPECIFICATIONS
Model name
Stitch system
Stitch pattern
Max. sewing speed
Max. zigzag width
Max. feeding amount
Lift of the presser foot
Hook
Thread take-up
Needle
(at the time of delivery)
Needle position
changing mechanism
Reverse feed stitching
mechanism
Bobbin thread winder
Needle throw pattern cam
Peripheral dimension
of the cylinder section
Lubrication
Lubricating oil
Power requirement/
Power consumption
Total weight
2358
The cylinder diameter is 322mm.
3-step 3-step Standard Standard
zigzag stitching zigzag stitching zigzag stitching zigzag stitching
Standard/3-step zigzag stitching pattern changeover lever
LZ-2284C-7
Standard/3-step zigzag
5,000rpm
Standard zigzag stitching: zigzag width of 5mm or less
3-step zigzag: zigzag width set to 8mm or less
Standard zigzag: 8mm/3-step zigzag: 10mm
Standard zigzag: 2.5mm/3-step zigzag: 2.0mm
By hand: 5.5mm/By knee: 10mm
DP hook (with titanium-treated inner hook)
Rotary type
SCHMETZ 134SUK, 438(#75)#65∼#90
ORGAN DP×5 #9∼#14
Provided as standard
Provided as standard
Built-in the machine head
Grooved cam
322mm
Automatic
JUKI New Defrix Oil No.1 (equivalent to ISO VG7)
Single-, 3-phase/650VA
86.5kg
SEPTEMBER, 2003 Printed in Japan(AD)