JUKI LZ-2290A Series Manual page 20

OPTIONS
Model
Part No.
–– 225-61559
–– 225-26578
RF-1 GRF-010000B0
–– 229-07406
–– B3129012A00
M097 MAM-097000A0
●Hook with non-rotational bobbin
The hook with non-rotational bobbin eliminates sewing troubles resulting from bobbin idling.
It provides a uniform bobbin thread tension at all times, thereby guaranteeing a consistent stitch formation.
235-23152 Hook
235-22550 Bobbin case (asm.)
235-23004 Bobbin
●Oilless bobbin case / Hook (special race surface plastic hook)
The oilless bobbin case and hook effectively prevent oil stains.
✽ When using the oilless bobbin and hook, a hook driving shaft front setscrew
(part number: 110-79506) is necessary.
●Parts for sewing with thick thread (recommended needle: DP × 5 #21, 134SUK Nm130)
●Presser foot connecting components
The aforementioned parts are used when a lockstitching type presser foot is installed on the machine.
Select a parts set of either the presser-bar changing type or the presser bar joining type, according to the type of presser foot of
your machine.
05
Description
Automatic reverse feed Kit
Hook with a hard blade point
Pedal-operated reverse feed
stitching device
Presser spring
Tension spring
Fagotting feller asm. (down-rolled
type)
Application
Precaution
Applicable thread
Not-applicable thread
235-57259 Hook compl. D
400-03609 Bobbin case D3 (compl.)
400-03610 Bobbin case D3 (asm.)
225-56054 Knife unit
D1440-583-H00 Needle thread guide
400-17095 Thread tension disk (asm.)
225-80369 Presser foot (asm.)
•Presser foot connecting components
(replaceable presser bar)
D1501-583-H00 Presser bar
D1502-583-H00 Presser connecting rod
SS-7091110-TP Screw
This device allows a machine without thread trimmer to perform automatic
reverse feed function.
Prevents the blade point of the hook from wearing out
The device enables the operator to perform reverse feed stitching using the pedal
without using the right hand. (excluding the LZ-2285N)
This is the spring which strongly holds down the material when sewing a heavy
weight material.
Tightly tensed seams can be produced by increasing the tension applied to the
needle thread.
This is the exclusive fagot stitch folder for the LZ-2285N, which is applicable to
the sewing of lingerie, foundation garments and baby wear.
(The fagot stitch folder asm. (up-rolled type):
The MAM-09700BA0 has been factory-installed on the machine prior to delivery.)
Mainly for the standard zigzag stitch: Effectively prevents the material
swelling at the sewn part, as well as irregular stitches when sewing lace to
slips, camisoles and shorts.
The quantity of thread to be wound around this bobbin is approximately
60% of that wound around the conventional bobbin. Therefore, this bobbin
is not recommended for pattern stitching such as three-point zigzag
stitching and scallop stitching, or intape-attaching processes, even if the
stitch system is the standard zigzag stitch.
Thread specifically developed for sewing foundation garments and lingerie
such as Resilon, Poelon, Satin, and Berlon (#50, #60)
Thread which has naps, decorative yarn of multi-fiber thread such as
woolly thread, Berlon D420 and D300, and spun thread
✽ If you want to use a non-rotational bobbin, consult your distributor beforehand.
●Hook gib
Soft seams can be produced by lowering the bobbin
thread tension.
•Presser foot connecting components
B1551-586-000
SS-7090910-TP
Feature
400-16408 Hook gib VS
Presser foot connecting foot
Screw