Serial Numbers; Cleaning And Maintenance - Peg-Perego si switch Instructions For Use Manual

ventilation (fig_b).
To release the hood, unfasten the attachments on the
two sides of the seat (fig_c)
The hood includes a slot from which you can hang
your child's favorite toy (fig_d).
9 FOOT MUFF Si Switch COMPLETO: to fasten it
correctly, slip the foot muff under the footrest and leg
rest and place it over the seat, keeping the front bar on
the outside. Fasten the FIRST button of the foot muff
to the inside of the stroller (fig_a) and hook the frog
fastenings, also to the front bar (fig_b).
On lowering the stroller's backrest, it is possible to
place the foot muff higher up and cover the child
better. To do this, fasten the SECOND button of the
foot muff to the inside of the stroller (fig_c) and hook
the frog fastenings to the highest loops (fig_d).
10 RAIN CANOPY Si Switch COMPLETO: to add the rain
canopy, place it on the stroller, fasten it at the sides to
the inside of the frame (fig_1), and fasten the elastics
after pulling them round the lower part of the stroller
frame (fig_2).
11 5-POINT SAFETY HARNESS: to fasten, insert the two
buckles of the waist strap (with attached shoulder
straps, arrow a) into the leg divider strap until they
click into place (arrow b). To unfasten them, press the
button which is situated in the centre of the fastener
(arrow c) and pull the waist strap outwards (arrow d).
12 To tighten the waist strap, pull on both sides in the
direction of the arrows; to loosen it, do the opposite.
13 It is possible to set the safety harness at 3 different
heights, depending on how tall the child is. As the
child gets bigger, the harness must be moved to a
higher position.
14 To adjust the height of the safety harnesses, release
the two buckles on the rear of the backrest.
Pull the shoulder straps towards you (arrow a) until the
buckles are released and insert them in the backrest
loops (arrow b). Remove the shoulder straps from the
sack (arrow c) and insert them in the most appropriate
buckle (arrow d), then reattach the two buckles
behind the backrest (arrow e). The buckles are securely
attached when a click is heard (fig f).
15 ADJUSTING THE LEG REST: The leg rest can be adjusted
in 2 positions. To lower it, pull the two side levers
downwards and at the same time lower the leg rest. To
raise it, push the leg rest upwards until it locks into place.
ADJUSTING THE BACKREST: The backrest reclines into
various positions. To lower the backrest, lift the handle
and simultaneously lower the backrest, locking it in
desired position. To raise it, push the backrest upwards.
16 REVERSIBLE SEAT The seat can be attached to the
frame facing either mom (fig_a) or the world (fig_b).
17 RELEASING/FASTENING THE SEAT
To release the seat: press the side buttons
simultaneously and lift the seat, which will have
unfastened, by pressing on the rounded area of the
structure, as shown in the figure (fig_a).
To fasten the seat: place it on the frame with the side
buttons corresponding to the relevant holes; the seat
will click into place (fig_b).
Ensure the two side buttons are properly secured.
18 CLOSING THE STROLLER: The stroller can be closed:
• without the seat
• with the seat facing mom
• with the seat facing the world.
To close the stroller with the seat docked (in either
direction), you must:
close the hood, lower the backrest fully, lower the
front bar to the 2nd position (closing position), and
lock the front wheels.
One at a time, lift the levers on the handles until you
hear a clicking sound (fig_a)
19 Grasp the central handle and pull it upwards until the
stroller folds up. Check the safety fastening to ensure
the frame has folded properly. When folded, the
stroller will stand upright.
20 The stroller folds up more compactly if you release the
seat (paragraph 17).
21 CARRYING: The stroller can be conveniently carried
(with the front wheels set on stationary) by the central
handle (fig_a). It can also be carried by the side handle
(fig_b).
22 REMOVING THE COVER: to remove the cover from the
stroller,
remove the seat from the frame (paragraph 17a);
slide the cover off the footrest (fig_a);
detach the 4 elastic bands from the sides of the
backrest (fig_b);
remove the crotch strap (fig_c);
23 slide out the two buckles (fig_d);
unscrew the strap's two screws on both sides using a
screwdriver and pliers to hold the nut steady (fig_e);
remove the cover from the top.
FASTENING
NAVETTA POP-UP & PRIMO VIAGGIO SL
24 NAVETTA POP-UP: To fasten the Navetta Pop-Up bassinet,
sold separately, to the frame, you will need to buy the
adapters as additional accessories. To attach the bassinet
properly, consult the relating instruction manual.
PRIMO VIAGGIO SL: To fasten the Primo Viaggio SL car
seat, sold separately, to the frame, you will need to buy
the adapters as additional accessories. To attach the car
seat properly, consult the relating instruction manual.

SERIAL NUMBERS

2 The Si Switch seat provides the following
5
information: product name, production date and
serial number. This information is essential in the
event of a claim (fig_a).
The Si Switch backrest provides the following
information: product name, production date and
serial number. This information is essential in the
event of a claim (fig_b).
ACCESSORIES
26 MOSQUITO NET: may be fastened to the hood (fig_a).
BAG: this baby changing bag with mat may be
fastened to the stroller (fig_b).
CUP HOLDER: may be secured to the mushroom
button on the frame (fig_c)
27 TRAVEL BAG: Practical bag for air travel with the
stroller (fig_d).
FASTENING ADAPTERS: adapters for attaching the
PegPerego Primo Viaggio SL car seat (Group 0+),
Navetta Pop-Up bassinet (group 0), to the frame (fig_e).
PARASOL: a handy matching parasol (fig_f).
PADDED CUSHION: for Peg Perego high chairs and
strollers. Winter side of quilted jersey fabric, summer
side of 100% cotton (fig_g).
VARIO FOOT MUFF: Foot muff for Peg Perego strollers
(fig_h).

CLEANING AND MAINTENANCE

PRODUCT MAINTENANCE: protect from the weather:
water, rain, or snow; prolonged and continuous
exposure to bright sunlight may give rise to colour
changes of various different materials; store this
product in a dry place.
CLEANING THE CHASSIS: periodically clean all plastic parts
with a damp cloth. Do not use solvent or similar cleaning
products; keep all metal parts dry to prevent rusting;
keep moving parts clean (adjustment mechanisms,
locking mechanisms, wheels, ...) and free of dust and sand
and, if necessary, lubricate with light machine oil.
- 16 -