Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Panasonic WV-CL920
Summary of Contents for Panasonic WV-CL920
-
Page 1: Operating Instructions
(Lens : option) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. Color CCTV Cameras Operating Instructions WV-CL920 Model No. WV-CL924... - Page 2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead sym- bol, within an equilateral triangle, is intended to alert the user to the pres- ence of uninsulated "dangerous volt- age"...
-
Page 3: Table Of Contents
PREFACE ... 4 FEATURES ... 4 PRECAUTIONS ... 5 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ... 6 CONNECTIONS ... 9 FOCUS OR FLANGE-BACK ADJUSTMENT ... 13 INSTALLATION OF CAMERA ... 14 SETUP ... 16 1. CAMERA SETUP MENU ... 16 2. -
Page 4: Preface
PREFACE Panasonic's WV-CL920 (WV-CL924) series digital color camera introduces a new level of high picture quality and high resolution through the use of a 1/2-inch frame interline transfer CCD image sensor having 768 hori- FEATURES 1. The following functions are built in. -
Page 5: Precautions
Use the camera under conditions where tempera- ture is between 10°C - +50°C (14°F - 122°F), and humidity is below 90 %. The input power source is 120 V AC 60 Hz for WV-CL920 and 12 V DC/24 V AC for WV-CL924. Caution:... -
Page 6: Major Operating Controls And Their Functions
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS CL920 Hi-Z G/L 75 CL920 Slide the panel to the left until it locks. <WV-CL920> LOCK <WV-CL924> LOCK 120V AC 60Hz VIDEO OUT GEN-LOCK DC 12V AC 24V VIDEO OUT GEN-LOCK... - Page 7 q Auto Iris Lens Connector This connector is used to connect the auto iris lens with a 4-pin male connector supplied as a standard accessory (Part No. YFE4191J100). w Flange-back Adjusting Ring (FB) This ring is used to adjust the back focal length or picture focus.
- Page 8 !3 Power Cord Socket This socket is used to connect the power cord (supplied as a standard accessory). !4 AC/DC Compatible Input Terminal (DC 12V IN/AC 24V IN) This terminal is for connecting the 12 V DC or 24 V AC power supply cord.
-
Page 9: Connections
CONNECTIONS A. WV-CL920 (120 V AC 60Hz) 1. Plug the AC power cord (supplied as standard accessory) into the AC Inlet Socket. 2. Connect the AC power cord to a 120 V AC 60 Hz outlet. Notes: • Connect the power cord firmly. -
Page 10: Video Cable
2. 24 V AC Power Supply Connect the power cable to the AC/DC compatible input terminal on the rear panel of the camera. DC 12V AC 24V 24 V AC, 60 Hz (19.5 V - 28 V) Recommended wire gauge sizes for 24 V AC line. Copper wire size (AWG) (0.22 mm... - Page 11 Installation of Auto Iris Lens Connector Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified service personnel or system installers. (1) Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover as shown in the diagram below.
-
Page 12: Mounting The Lens
Mounting the Lens Caution: Before you mount the lens, loosen the fixing screw on the side of the camera, and rotate this ring upward until it stops. If the ring is not at the end, the inner glass or CCD image sensor may be dam- aged. -
Page 13: Focus Or Flange-Back Adjustment
FOCUS OR FLANGE-BACK ADJUSTMENT The following adjustment should be made by qualified service personnel or system installers. 1. Loosen the screw on the side of the camera. Flange-back Adjusting Ring Screw 2. Turn the flange-back adjusting ring to the desired position. -
Page 14: Installation Of Camera
INSTALLATION OF CAMERA • Mounting from the top Fixing Screws Remove the mount adapter from the bottom of the camera by removing the two fixing screws. Attach the mount adapter to the top as shown in the dia- gram, then mount the camera on the mounting Mount Adapter bracket. -
Page 15: Setup
SETUP 1. CAMERA SETUP MENU This camera utilizes a user setup menu that is displayed on-screen. The setup menu contains various items that form a tree type structure. Camera ON/OFF Camera PRESET PRESET ON (Back Light Editing Compensation) Camera ID Manual Manual Display... - Page 16 Lens Drive White Signal Motion Balance Selection Detector ATW1 ATW2 AWC DC VIDEO Manual Detection UP SIDE Mask Area Level DOWN Selection Adjustment Manual Display Mask Area Mode Selection Special Menu CHROMA PEDESTAL GAIN GAIN -17- BURST Camera (BW) Resetting AUTO1 AUTO2 ON OFF ON OFF...
- Page 17 • Opening the Setup Menu Press and hold down for 2 seconds or more. ** CAM SET UP ** CAMERA ID ALC/ELC SHUTTER ON (DNR-H) SENS UP SYNC WHITE BAL ATW1 MOTION DET LENS DRIVE SET UP DISABLE The CAM SET UP menu appears on the monitor as shown above.
-
Page 18: Setup Operation
2. SETUP OPERATION This camera utilizes a user setup menu (CAM SET UP) that is displayed on the monitor. To set items on the CAM SET UP menu, use the follow- ing buttons on the side panel. Left Button Set Switch Up Button ( Moves the cursor upwards. - Page 19 • Editing the CAM SET UP Menu Important Notice: When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you cannot change the currently active settings. This is to prevent acciden- tal changing of the settings. To edit the CAM SET UP menu (change settings), press to move the cursor to SET UP DISABLE in the bottom line.
-
Page 20: Setting Procedures
SETTING PROCEDURES 1. Camera Identification (CAMERA ID) Setting You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. The camera ID display can be switched on or off on the monitor screen. - Page 21 1. Move the cursor to POSI, and press play shown below appears and the CAMERA ID is highlighted. Highlighted WV-CL920 2. Move the CAMERA ID to the desired position by pressing 3. Press The mode returns to the previous CAMERA ID menu.
- Page 22 1. Move the cursor to the ALC/ELC parameter. 2. Select ALC or ELC. Cautions: 1. Under bright lighting conditions such as outdoors, use an ALC type lens because the ELC control range is not wide enough under these conditions. 2. Use an ALC type lens if the following phenomena occur: •...
- Page 23 ** ALC CONT ** BACK LIGHT COMP PRESET MASK SET LEVEL ...I... ** ALC CONT ** BACK LIGHT COMP PRESET LEVEL ...I... 2. Move the cursor to the PRESET parameter and select ON. The backlight compensation is automatically set. 3. If you want to change the video output level (pic- ture contrast), move the “I”...
- Page 24 2. Move the cursor to MASK SET and press The 48 mask areas appear on the monitor screen. The cursor is blinking in the top left corner of the screen. Blinking 3. Move the cursor to the area where backlight is bright, and press to mask that area.
- Page 25 3. Shutter Speed Setting (SHUTTER) Note: When ELC is selected for ALC/ELC on the CAM SET UP menu, this item is not available. You can select an electronic shutter speed of 1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, or 1/10 000 seconds.
- Page 26 5. Electronic Sensitivity Enhancement (SENS UP) There are two modes for SENS UP. AUTO: If you select x32 AUTO, for example, the sensitivity is raised automatically to x32 max. When AUTO is selected, AGC is automatically set to ON. FIX: If you select x64 FIX, for example, the sensitiv- ity is raised to just x64.
- Page 27 6. Synchronization Setting (SYNC) You can select internal sync mode (INT) or line-lock mode (LL). Additionally, this model accepts the VBS signal (color composite video or blackburst signal) and VS signal (B/W composite video or composite sync sig- nal). The VD2 signal (multiplexed vertical drive signal) with the composite video output signal from external equipment such as a Matrix Switcher is also accept- able.
- Page 28 6. The VS gen-lock mode has a submenu for horizon- tal phase adjustments. When the cable length of the video output or the gen-lock input is changed, the horizontal phase must be re-adjusted. 7. The line-lock mode has a submenu for line-lock vertical phase adjustment.
- Page 29 8. Adjust the horizontal phase by pressing . The adjustable range is 0 - 2.0µs. 9. Move the cursor to SC COARSE. 10. Press to match the chroma phase of the camera’s video signal, when observed at the out- put of the Special Effect Generator (SEG) or Switcher, as closely as possible to the color of the original scene.
- Page 30 6-2. VS Gen-lock Mode (EXT(VS)) 1. Move the cursor to the SYNC parameter and select INT. 2. Connect the coaxial cable for the composite sync or composite B/W video signal to the gen-lock input connector. 3. Confirm that the parameter INT changed to EXT (VS) on the menu.
- Page 31 2. After confirming the cursor is on LL, press vertical phase adjustment menu appears on the monitor. ** SYNC ** V PHASE COARSE 1(1--16) FINE I... 3. Supply the video output signal of the camera to be adjusted and the reference camera video output signal to a dual-trace oscilloscope.
- Page 32 • To reset COARSE and FINE to the values pre- set at the factory, press neously. COARSE and FINE adjustments are preset at the factory to zero-crossing of the AC line phase. • If the AC line contains noise (spike noise, etc.), the stability of the vertical phase of the camera video output signal may be disturbed.
- Page 33 Automatic White Balance Control Mode (AWC) • In this mode, accurate white balance is obtained within a color temperature range of approximately 2 300-10 000K. 1. Move the cursor to the WHITE BAL parameter and select AWC PUSH SW. ** CAM SET UP ** CAMERA ID ALC/ELC SHUTTER...
- Page 34 5. Press to obtain the optimum amount of blue gain. Note: When you need to set MASK SET, re-adjust to obtain the optimum amount of red and blue gain. 8. Motion Detector Setting (MOTION DET) The motion detector detects the moving objects in the scene by monitoring changes in brightness level.
- Page 35 Therefore, when the camera is not used in a Panasonic Intelligent CCTV System, select OFF to prevent the above from occurring. 9. Lens Drive Signal Selection...
- Page 36 10. Special Menu (SPECIAL) This menu lets you adjust and set up the video signal of the camera to meet your requirements. Move the cursor to END on the bottom line of the CAM SET UP menu and press (hold down and press ) for 2 seconds or more.
- Page 37 Default: OFF AUTO1: The camera selects black and white mode if the picture is dark, or color mode if the pic- ture is bright enough. Note: Color picture switches to black-and- white picture and vice versa in approxi- mately 1 or 2 minutes after recognition of illuminance.
-
Page 38: Prevention Of Blooming And Smear
To reset to the factory settings 1. Move the cursor to the CAMERA RESET parameter. PUSH SW is highlighted. 2. While holding down seconds or more. The camera is reset to the facto- ry settings. PREVENTION OF BLOOMING AND SMEAR When the camera is aimed at a bright light, such as a spotlight, or a surface that reflects bright light, smear or blooming may appear. -
Page 39: Specifications
1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000,1/2 000,1/4 000, 1/10 000 s selectable CS-mount DC or Video selectable –10°C - +50°C (14°F - 122°F) Less than 90 % WV-CL920: 120 V AC 60 Hz 4.8 W WV-CL924: 24 V AC 60 Hz 4.9 W 12 V DC 460 mA... - Page 40 Weights and dimensions indicated are approximate. Specifications are subject to change without notice. 74 mm (W) x 55 mm (H) x 120 mm (D) [2-15/16” (W) x 2-3/16” (H) x 4-13/16” (D)] WV-CL920: 0.45 kg (1.0 lbs.) (without power cord) WV-CL924: 0.44 kg (1.0 lbs.)
-
Page 41: Standard Accessories
STANDARD ACCESSORIES Body Cap ... 1 pc. ALC Lens Connector (YFE4191J100) ... 1 pc. AC Power Cord (only WV-CL920) ... 1 pc. C-mount Adapter ... 1 pc. -42-... -
Page 42: Optional Accessories
OPTIONAL ACCESSORIES Lenses : WV-LA2.8, WV-LA4R5A, WV-LA6A, WV-LA12A, WV-LZ80/2, WV-LZ81/10, WV-LZ81/6A, WV-LA4510, WV-LA608, WV-LA1208 -43-... - Page 43 Panasonic Security and Digital Imaging Company A Division of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Regional Offices: Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee,...