Weider SPARRING SYSTEM User Manual page 11

Seat Assembly
28. Attach the Backrest (21) to the Front Upright (4)
with two M6 x 63mm Screws (72) and two M6
Washers (81).
29. Press a 38mm Square Inner Cap (57) into the
Seat Frame (15).
Insert the M6 x 50mm Carriage Bolt (68) into the
centre hole in the Seat Plate (19). Attach the Seat
Plate to the Seat (20) with two M6 x 16mm
Screws (67).
Insert the M6 x 50mm Carriage Bolt (68) into the
indicated hole in the Seat Frame (15). Tighten an
M6 Nylon Locknut (82) with an M6 Washer (81)
onto the Carriage Bolt.
Attach the other end of the Seat (20) to the Seat
Frame (15) with an M6 Washer (81) and the M6 x
50mm Screw (76).
30. Press a 38mm Square Inner Cap (57) into the
Leg Lever (16).
Lubricate the M8 x 59mm Bolt (77) with grease.
Attach the Leg Lever (16) to the Seat Frame (15)
with the Bolt and an M8 Nylon Locknut (83). Do
not overtighten the Locknut; the Leg Lever
must be able to pivot freely.
Insert an M10 x 98mm Eyebolt (64) through an
M10 Washer (86) and the Leg Lever (16), from
the direction shown. Tighten an M10 Nylon
Locknut (84) and another M10 Washer (86) onto
the Eyebolt.
31. Rest the Seat Frame (15) on the indicated pin in
the Front Upright (4). Attach the Seat Frame to
the Front Upright with an M8 x 68mm Carriage
Bolt (66) and the Seat Knob (60).
28
4
21
72
81
72
81
29
20
68
19
57
67
15
82
81
76
30
15
83
Lubricate
77
16
64
86
86
84
57
31
66
15
60
4
14
17. Route the Long Cable (41) around a "V"-pulley
(46). Attach the "V"-pulley and a Long Cable Trap
(43) to the bracket on the Left Arm (11) with an
M10 x 58mm Bolt (79) and an M10 Nylon Locknut
(84). Make sure that the Cable is in the groove
of the Pulley and that the Cable Trap is posi-
tioned to hold the Cable in place.
18. Route the Long Cable (41) around a "V"-pulley
(46). Attach the "V"-pulley and a Long Cable Trap
(43) to the bracket on the Right Arm (12) with an
M10 x 58mm Bolt (79) and an M10 Nylon Locknut
(84). Make sure that the Cable is in the groove
of the Pulley and that the Cable Trap is posi-
tioned to hold the Cable in place.
19. Route the Long Cable (41) around a 90mm Pulley
(45). Attach the Pulley and a pair of Pulley
Covers (44) to the Pulley Bracket (51) with an
M10 x 53mm Bolt (94) and an M10 Nylon Locknut
(84). Make sure that the large tabs on the
Pulley Covers are in the position shown.
Make sure that the M8 x 117mm Bolt (78) is prop-
erly tightened and that the Pulley Bracket (51)
can move freely.
20. Wrap the Long Cable (41) around a 90mm Pulley
(45). Attach the Pulley and a pair of Pulley
Covers (44) to the upper hole in the Long "U"-
bracket (50) with an M10 x 53mm Bolt (94) and
an M10 Nylon Locknut (84). Make sure that the
small tabs on the Pulley Covers are in the
position shown.
Pin
17
79
43
46
Bracket
41
11
84
18
79
43
46
Bracket
12
41
84
19
44
78
94
45
84 51
Large
41
Tabs
20
41
Small
44
Tabs
44
45
84
94
50
11