Page of 4
Download Bookmark Comment

Nortel 1140E User Manual

Panasonic bluetooth headset user manual.
Also See for 1140E:
User manual - 216 pages
User manual - 29 pages
Quick reference manual - 19 pages
Nortel 1140e Bluetooth User Guide
Enabling Bluetooth
1 Double-press
Services to open the Local Tools menu.
2 Press the 3 key on the telephone dialpad to select 3. Network Configuration
3 Use the Right Arrow Key to scroll to Enable Bluetooth located at the bottom of the menu, change the value to YES
4 Press Apply & Reset to save your changes (the phone will reboot)
Bluetooth Setup
Your IP Phone 1140E is equipped with a Bluetooth wireless technology radio system to support
wireless headsets. You can access the Bluetooth Setup options using either of the following two methods:
1 Double-press the
Headset key to open the Bluetooth Setup dialog box. This method is used in
this document.
2 Double-press the
Services key to open the Local Tools menu, press 1 on the dialpad to select
1. Preferences, and press 3 on the dialpad to open the 3. Bluetooth Setup dialog box.
Contact your administrator to find out if Bluetooth wireless technology functionality is available
for your use.
To pair the wireless headset with your phone:
1 Check to make sure Bluetooth is enabled on your phone.
2 Double-press the
Headset key access 3. Bluetooth setup. Ensure the Enable Bluetooth & User Bluetooth Headset
check boxes are highlighted.
Note: The Bluetooth Setup menu entry is not available on all phones. If the
Bluetooth Setup menu entry appears dimmed, or fails to open when you double
press the Headset key, the feature is not enabled on your phone. Before you can
use a wireless headset with your phone, the feature must be enabled (see "Enabling Bluetooth")
Note: If Bluetooth wireless technology is enabled on your phone, and
password-protection for the Local Tools menu has been enabled, you can still
double-press the Headset key to access the Bluetooth Setup menu.
Note: If the Bluetooth Setup menu fails to open when you double press
the Headset key, Bluetooth wireless technology is not enabled on your
phone (see "Enabling Bluetooth").
3 Press the Enter key to activate Bluetooth wireless technology.
A check mark is displayed to indicate that the feature is activated. The message "BT Enabled"
appears at the bottom of the display.
4 Put your wireless headset in its pairing or search mode. The procedure for doing this can be
different for each wireless headset. Refer to the documentation that accompanied your headset,
or contact the vendor.
For example, if you are using the GN Netcom GN 6210, do the following:
a Turn the headset off by pressing and holding the telephone button for 3 - 4 seconds until a

   Also See for Nortel 1140E

   Related Manuals for Nortel 1140E

   Summary of Contents for Nortel 1140E

  • Page 1

    4 Press Apply & Reset to save your changes (the phone will reboot) Bluetooth Setup Your IP Phone 1140E is equipped with a Bluetooth wireless technology radio system to support wireless headsets. You can access the Bluetooth Setup options using either of the following two methods: 1 Double-press the Headset key to open the Bluetooth Setup dialog box.

  • Page 2

    high to low tone is heard. The headset blue LED turns off. b Press and hold the telephone button for about 8 seconds until the blue LED flashes and then lights steadily. 5 Search for (pair) the headset: a Press the Right navigation key twice to highlight the Search button, displayed next to the Search Devices item.

  • Page 3

    • If a single tone sounds, the headset is connected to the base. • If a double beep sounds, the headset is connected to the 1140E. If the base is powered off, the headset is only paired to the 1140E and pressing the "telephone" key connects you to the 1140E.

  • Page 4

    again either when the phone is idle or during an active call. To switch between a wired headset and wireless headset: 1 Double-press the (Headset) key to open the 3. Bluetooth Setup dialog box. 2 Press the Left/Right navigation key to select the Use BT Headset item. 3 Press the Enter key to toggle this option on or off.

Comments to this Manuals

Symbols: 0
Latest comments: