Installation Instructions Warning - Hoshizaki KM-30A Instruction Manual

IMPORTANT
1. This booklet is an integral and essential part of the product
and should be kept and preserved by the user. Please read
carefully the guidelines and warnings contained herein as
they are intended to provide the installer/user with essential
information for the proper installation and the continued safe
use and maintenance of the product. Please preserve this
booklet for any further consultation that may be necessary.
2. This is a commercial icemaker, and should be destined only
to be used for the purpose for which it has been expressly
designed. Any other use should be considered improper and
therefore dangerous. The manufacturer will not be held liable
or responsible for any damage caused by improper, incorrect
and unreasonable use.
I. INSTALLATION INSTRUCTIONS
WARNING
1. The installation must be carried out by qualified
personnel, in accordance with current regulations, according
to the manufacturer's instructions.
2. Keep ventilation openings, in the appliance enclosure or in
the built-in structure, clear of obstruction.
1. UNPACKING
WARNING
Children should not be allowed in reach of the packaging
elements (plastic bags and expanded polystyrene) as they are
potential sources of danger.
CAUTION
Remove shipping carton, tape(s) and packing. If packing
material is left in the icemaker, it will not work properly.
Top Panel
Separator
Door
Accessories
(inside bin)
Control Switch
Air Filter
1) After removing the packaging, make sure that the icemaker is in
good condition. If in doubt, please do not use the equipment but
apply to professionally qualified personnel.
2) Remove shipping tape holding the door and separator.
3) Remove the protective plastic film from the exterior. If the icemaker
is exposed to the sun or to heat, remove the film after the icemaker
cools.
4) Remove the package of accessories, and check the contents:
a) Outlet Hose
b) Scoop
c) Adjust Bolt
d) Power Supply Cord (European model)
Icemaking
Mechanism
Control Box
Refrigeration
Circuit
Louver
Fig. 1
1
1
4
1
2. LOCATION
1. This icemaker is not intended for outdoor use. Normal
operating ambient temperature should be within 7°C to 40°C.
Normal operating water temperature should be within 7°C
to 35°C. Operation of the icemaker, for extended periods,
outside of these normal temperature ranges may affect
production capacity.
2. The icemaker should not be located next to ovens, grills or
other high heat producing equipment.
3. The location should provide a firm and level foundation for
the equipment.
4. Allow 15 cm clearance at rear and sides for proper air
circulation and ease of maintenance and/or service should
they be required.
5. This appliance is not suitable for installation in an area where
a water jet could be used and where dripping is not allowed.
6. Do not place anything on top of the icemaker or in front of
the louver.
7. This icemaker will not work at subfreezing temperatures. To
prevent damage to the water supply line, drain the icemaker
when air temperature is below zero (see "II. 2. PREPARING
THE ICEMAKER FOR LONG STORAGE").
3. INSTALLATION
* Incorrect installation can cause harm to people, animals or things,
for which the manufacturer cannot be held responsible.
* Place the icemaker in the selected permanent site.
* The appliance must be positioned so that the plug is accessible.
4. ELECTRICAL CONNECTIONS
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national
and local electrical code requirements. To prevent possible
severe electrical shock to individuals or extensive damage to
equipment, install a proper earth wire to the icemaker. Remove
the plug from the mains socket before any maintenance, repairs
or cleaning is undertaken.
1:2
* This appliance requires a separate 220 - 240VAC, 10A supply. The
electrical supply must be protected by a suitable circuit breaker.
* The main control box fuse is rated at 5A and should only be
replaced by a qualified service engineer.
1:2
* Usually an electrical permit and services of a licensed electrician
are required.
[Europe]
* If the supply cord is damaged, it must be replaced by a replacement
cord available from Hoshizaki Parts/Service Centres.
[Other than Europe]
* If the supply cord and the plug should need to be replaced, it should
only be done by a qualified service engineer.
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in accordance with the
following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
1
ENGLISH
IMPORTANT
WARNING