Previous And Next [ ]/[ ] Buttons - Onkyo TX SR804 Instruction Manual

Zone 2—Continued
Controlling Zone 2 with the Remote
Controller
STANDBY
ON
INPUT
SELECTOR
Note:
• To control Zone 2, you must press the remote control-
ler's [ZONE 2] REMOTE MODE button first.
1 Press the [ZONE 2] REMOTE
ZONE2
MODE button, then point the
remote controller at the AV
receiver and press the [ON] but-
ton.
ON
Zone 2 turns on, and the ZONE 2 12V
TRIGGER OUT goes high (+12 V).
2 To select an input source for
Zone 2, press the [ZONE 2]
ZONE2
REMOTE MODE button, followed
by an INPUT SELECTOR button.
To select AM, FM, or XM, press the
[TUNER] INPUT SELECTOR button
V1 V2 V3
1 2 3
repeatedly.
V4 DVD
4 6
CD TAPE TUNER
7 8 9
PHONO
+ 10
3
To turn off Zone 2, press the
[ZONE 2] REMOTE MODE button,
ZONE2
followed by the [STANDBY] but-
ton.
STANDBY
84
ON STANDBY
T V
INPUT
I
V1 V2 V3
+
1 2 3
T V CH
V4 MULTI CH DVD
4 5 6 -
CD TAPE TUNER
7 8 9
T V VOL
PHONO
+ 10
0 CLEAR
10 11 12
- - /-- -
INPUT SELECTOR
MACRO
ZONE2
1 2 3 ZONE2
REMOTE MODE
RECEIVER DVD CD HDD
TAPE/AMP
LISTENING MODE
STEREO SURR
REPEAT AUDIO SUBTITLE PLAY MODE
PURE A DIRECT THX ALLST
TEST TONE CH SEL LEVEL LEVEL
LEVEL–,
OPEN/CLOSE VIDEO OFF
L NIGHT Re-EQ
LEVEL+
RC-620M
Adjusting the Volume for Zone 2
ZONE 2 LEVEL
STANDBY/ON
STANDBY
ZONE 2
POWER
ON OFF
PURE AUDIO MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3
PHONES
ZONE 2 OFF TONE STEREO DIMMER MEMORY
LISTENING MODE CLEAR
ZONE 2 LEVEL
1 On the remote controller, press
ZONE2
the [ZONE 2] REMOTE MODE but-
ton, and then use the [LEVEL–]
and [LEVEL+] buttons.
LEVEL LEVEL
On the AV receiver, use the ZONE
AV receiver
2 LEVEL [
ZONE 2 LEVEL
If your Zone 2 speakers are connected
to an amp in Zone 2, use its volume
control to adjust the volume.
To Mute Zone 2:
Press the remote controller's [ZONE 2] button, followed
by the [MUTING] button. To unmute Zone 2, press the
remote controller's [ZONE 2] button again, followed by
the [MUTING] button, or adjust the volume for Zone 2.
Notes:
• Only analog input sources are output by the ZONE 2
LINE OUT and ZONE 2 SPEAKERS terminals. Dig-
ital input sources are not output. If no sound is heard
when an input source is selected, check to see if it's
connected to an analog input.
• When the ZONE 2 SPEAKERS terminals are used,
listening modes that require surround back speakers,
such as Dolby Digital EX, DTS-ES, and THX Select2
Cinema, are unavailable.
• While Zone 2 is on, the
• You can't select different radio stations for the main
room and Zone 2. The same radio station will be used
for both.
,
MASTER VOLUME
VIDEO 4 TAPE TUNER CD PHONO DISPLAY
TUNING VIDEO 4 INPUT
MODE SETUP RETURN ENTER SETUP MIC
PRESET PRESET
TUNING DIGITAL S VIDEO VIDEO L AUDIO R
]/[ ] buttons.
functions do not work.