Connecting The Subwoofer And The Swa-8000S (Sold Separately); Connecting The Surround Speakers (Sold Separately) - Samsung HW-K450 User Manual

CONNECTIONS
● Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
● If you use a device that uses the same frequency (2.4GHz) as the Soundbar near the Soundbar,
interference may cause some sound interruption.
● The maximum transmission distance of the wireless signal between the main unit and subwoofer is about 5
meters, but may vary depending on your operating environment. If a steel-concrete or metallic wall is
between the main unit and the wireless subwoofer, the system may not operate at all because the wireless
signal cannot penetrate metal.
● If the main unit doesn't make a wireless connection, repeat steps 1-5 on the previous page to re-set the
connection between the main unit and wireless subwoofer.
● The wireless receiving antenna is built into the wireless subwoofer. Keep the unit away from water and
moisture.
● For optimal listening performance, make sure that the area around the wireless subwoofer location is clear
of any obstructions.
Expand to true wireless surround sound by connecting the Samsung Wireless
Rear Speaker Kit (SWA-8000S) to your Soundbar. (Sold separately)
CONNeCTING THe SuBWOOFer AND
THe SWA-8000S (SOLD SePArATeLY)
COnnECTIng THE SUBWOOFER AnD THE SWA-8000S
MAnUALLy
If the blue LeD lights do not stop blinking when the main unit, subwoofer, and SWA-8000S are turned on, please reset
the linking ID by following the procedure below.
1. Plug the power cords of the main unit, subwoofer and the SWA-8000S into an AC wall outlet.
2. Press the ID SET button on the back of the subwoofer and the SWA-8000S with a small, pointed object for 5
seconds.
• The LINK indicators (Blue LeDs) of the subwoofer and the SWA-8000S blink quickly.
3. Press the
button on your remote control for 5 seconds while the main unit is turned OFF.
4. The ID SeT message appears on the display of the main unit for a short period of time, and then disappears.
5. While the subwoofer's and the SWA-8000S's indicators are flashing blue, press the
on the right side of the main unit to turn on the main unit.
6. The connection is complete if the blue LeDs on the subwoofer and the SWA-8000S stop blinking and glow
continuously.
L R
SURROUND SPEAKERS OUT
SPEAKER IMPED
ID SET
button on your remote control or
18
• The main unit, the subwoofer and the SWA-8000S should now be linked (connected).
• The LINK indicators (Blue LeDs) on the subwoofer and the SWA-8000S should be glowing continuously and
not blinking.
• If the LINK indicators are not solid blue, the linking process has failed.Turn off the main unit, go back to Step 2,
and start again.
• You can enjoy better sound from the wireless subwoofer by selecting a Sound effect. (See page 9)
COnnECTIng THE SURROUnD SPEAKERS (SOLD
SEPARATELy)
Surround Speaker (L)
Wireless Receiver Module
● Place these speakers to the side of your listening position. If there isn't enough room, place these
speakers so they face each other. Position them about 60-90 cm above your ear, facing slightly
downward.
● Surround speakers must be connected to the wireless receiver module.
● each speaker has a colored label on its back or underside. each cable has a single colored band near its end.
Match the band on each cable to the speaker label by color, and then connect the cable to the speaker.
CONNECTIONS
L R
SURROUND SPEAKERS OUT
SPEAKER IMPED
ID SET
Surround Speaker (R)
19