Initial Operation - Metabo SB 710 Original Instructions Manual

en ENGLISH
6. Overview
Fig. A
1 Thumb-wheel for gear selection
2 Additional handle/Additional handle with
vibration damping *
3 Depth stop
4 Geared chuck *
5 Futuro Plus keyless chuck *
6 Futuro Top keyless chuck *
7 Sliding switch (normal drilling/impact drilling)
8 Speed preselection wheel *
9 Setting wheel for torque control and impulse
function *
10 Electronic signal indicator *
11 Rotation selector switch *
12 Lock button for continuous activation
13 Trigger
* depending on model

7. Initial Operation

Before plugging in the device, check to see
that the rated mains voltage and mains
frequency, as specified on the rating label, match
your power supply.
To guarantee secure purchase of the chuck:
After initial drilling (clockwise), use a screw-
driver to firmly tighten the safety screw inside the
drill chuck (if available/depending on the model).
THE SAFETY SCREW HAS A LEFT-HANDED
THREAD!
7.1 Fitting the additional handle (2)
B
For safety reasons, always use the additional
handle supplied.
Tighten the additional handle firmly by turning it.
8. Use
8.1 Setting depth stop
8.2 Setting direction of rotation, transporting
safety device (switch-on lock)
Do not activate the rotation selector switch
(11) unless the motor has completely stopped.
8.3 Setting for normal drilling, impact drilling
Fig. E
Impact drilling and normal drilling only in a
clockwise direction.
8.4 Selecting gear
Change thumbwheel (1) only when the
machine is in the process of running down
(briefly switch it on and off).
14
Fig.
Fig. C
Fig. D
Fig. F
8.5 Setting torque control, impulse function
Fig. G
Position 1-6: The motor comes to a complete stop
when the preselected torque is reached.
1 = low torque
6 = high torque
+ = no torque control (max. torque, for drilling)
= impulse function switched on constantly (to
facilitate tightening and releasing of screws
that are tight even when the screw heads are
damaged. To enable clean drilling without
centre punching in tiles, aluminium or other
materials).
8.6 Preselecting rotational speed
See the table for recommended rotational speeds
for drilling.
8.7 Switching On and Off
Switching on, rotational speed
the trigger (13).
Release the trigger to switch off.
Continuous operation
(13) pressed, push in the locking button (12) and
release the trigger. Press and release the trigger
(13) again to switch off.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
8.8 Tool change, Futuro Top keyless chuck
(6) Fig. I
Clamp the tool by turning the sleeve firmly to its
stop.
8.9 Tool change, Plus (5) keyless chuck
Fig. J
The ratchet sound which can possibly be heard
after opening the drill chuck is functional and is
switched off by a reverse rotation of the sleeve.
If the chuck is very tightly closed: Firmly grip the
chuck with an open-end spanner at the chuck head
and firmly turn the sleeve in the direction of the
arrow -1.
Clamping the tool
- Insert the tool -2- as far as possible.
- Using one hand, hold the retainer ring securely
(depending on fittings).
- Turn sleeve in direction -3- until the noticeable
mechanical resistance has been overcome.
- Caution! The tool is not yet fully tightened!
Keep turning the sleeve (it must "click" when
turning) until it cannot be turned any further - only
now is the tool safely clamped.
With a soft tool shank, retightening may be required
after a short period of operation.
8.10 Tool change, geared chuck (4)
Fig. H
Fig. A: Press
Fig. A: With the trigger
Fig. K