Before Installation; Installation; Contact Your Local Building Authorities Regarding Restrictions And Installation Requirements - Jøtul FS 162 Installation And Operating Instructions Manual

3.0 Before installation

3.1 Distance to inflammable material
See Fig. 1 A.
3.2 Foundations
You need to make sure the floor is suitable for the entire
installation. See "2.0 Technical data" for specified weight.
Flooring that is not attached to the foundation – "floating floors"
– must be removed beneath the product.
Remember: If a steel chimney resting on the insert is being used,
the weight of the steel chimney must be taken into account.
NB: It is extremely important to ensure that the product is stable;
the surface it is installed on must be completely inflexible.
3.3 Floor covering
The surround has an airtight bottom plate, so no extra floor
covering is required beneath the product.
Any floor covering of inflammable material, such as linoleum,
carpets, etc. must be removed from under the installation area.
3.4 Floor plate
A plate made of steel or some other suitable non-inflammable
metal (optional extra) is placed in front of the hearth.
Contact your local building authorities regarding restrictions and
installation requirements.
3.5 External air
A flexible supply tube for combustion air must be installed
through a hole in the back of the surround, or else through the
hole cut where marked in the bottom plate. See also point 3.1 in
the manual "Jøtul F 370 Series".
3.6 Steel chimney
If a top-mounted steel chimney is used, an uninsulated pipe
is fitted from the insert to approximately 1 cm over the valve
plate 1 and 2 (part 19+20). A 60 mm offset pipe (optional extra)
must be used. Then fit the steel chimney in accordance with the
operating instructions.

4.0 Installation

The product is heavy! Ensure you have help when positioning
and installing it.
Make sure that the door to the burn chamber is closed during
installation so that the product is not nose-heavy.
must be secured so that it does not topple over while you are
installing it.
The product is supplied together with 3 manuals:
• General use and maintenance instructions
• Jøtul FS 162 – 370 (surround)
• Jøtul F 370 Series (burn chamber)
4.1 Prior to installation
1. The standard product is supplied in two packages: the burn
chamber and surround with mounting sections.
2. Once the burn chamber has been unpacked, remove the burn
plates, baffle, exhaust deflector, inner bottom, ash pan and
riddling grate. The small side burn plates and the gasket for
the flue pipe, which can be found in the ash pan, are also
removed.
3. Remove the top plate with the top grate.
to be used.
4. Check that there is no visible damage to the product when
you unpack it, and make sure that the control handles move
freely.
5. Spread the cardboard packaging over the floor, and lay the
stove down carefully on its side.
6. The product is supplied from the factory with the smoke
outlet fitted for the top outlet. Select top outlet or rear outlet.
If rear outlet for the flue pipe is selected, first drill a hole in
the removable cover plates for the smoke outlet before they
are knocked out. See also point 3.1 in the Installation Manual
for the Jøtul F 370.
If rear outlet is selected, proceed as follows:
• The wooden block that holds the exhaust deflector in place
should be positioned so that it supports the side plates
when the cover plates are knocked out.
• Unscrew the smoke outlet (fig. 16B) from the top outlet.
• Unscrew the cover for the rear outlet from the inside of
the burn chamber (fig. 16A).
• Place the gasket on the edge of the flue pipe
• Attach the smoke outlet
pipe with the gasket.
• Secure the cover onto the top outlet
screws that held the smoke outlet in place.
7. Attach the four threaded bars together with sleeves and nuts
(parts 23, 24 and 25) beneath the burn chamber. See fig. 2A+B.
Screw the threaded bars (part 25) into the bottom of the burn
chamber, slide the sleeves (part 24) on and tighten the nuts
(part 23). Make sure that the locking bracket is placed on one
of the two rear sleeves before fitting the nuts, fig. 2B.
8. Fit a flex hose for combustion air (part 21). See
necessary, this can be fitted later, depending on the distance
to the wall. See fig. 11 B+C.
9. Fit the ornamental stones
side frames using the relevant screws, see Fig. 4. These are
adjusted after being mounted on the surround.
ENGLISH
The product
These parts are not
(fig. 5A).
(fig. 5B) to the end of the flue
(fig. 18) using the
fig. 3. If
(part 12) against the back of the
19