S Toring Y Our I Ron - Sunbeam 4267-33 Manual

to the appropriate setting.
Tip: Refer to the Ironing Guide for the recommended setting for your fabric.
Important: When not ironing, always set the Steam Selection Slide to OFF (Dry).
u
sIng the
®
s m f
pRaY Ist eatuRe
The Spray Mist ® feature is a powerful water spray mist that dampens the fabric
to aid in removing wrinkles from heavy fabrics and for setting creases.
t s m f :
®
o use the pRaY Ist eatuRe
Press the Spray Mist ® button firmly. Iron over the fabric to dry.
®
s s f
hot of team eatuRe
The Shot of Steam ® feature provides an extra burst of steam for deep penetration of stubborn wrinkles. You can use
this feature while Dry or Steam ironing, but the water reservoir must be at least 1/4 full of water.
t s s f
®
o use the hot of team eatuRe
Place the iron on top of the wrinkle and press the Shot of Steam
steam. The Shot of Steam ® feature may be used continuously with just a short 3 second pause between shots.
v s
eRtIcal team
The vertical steam feature allows your iron to function as a garment steamer.
Tip: When using the vertical steam on clothing, hang the clothing on a clothes hanger for best results. Hanging
curtains and drapes may also be steamed.
t v s :
o use eRtIcal team
1. Make sure that the iron has heated up (2 minutes).
2. H old the iron in a vertical position, with the iron close to but not touching the fabric you want to steam.
3. With your other hand, pull the fabric tight.
®
4. P ress the Shot of Steam button for approximately 3-second intervals as you move the iron across the wrinkled
area.
WARNING: To prevent the risk of burns, keep your hand away from the area being steamed.
WARNING: DO NOT steam garments while wearing them; this may result in injuries.
3-W m s ™ a -o
aY otIon maRt uto ff
When the iron is plugged in and the Auto-Off is activated, the OFF selection on the digital display and the red Wait
light will blink, indicating that the iron has stopped heating. The Auto-Off is activated if not moved after 30 seconds
in the ironing position and on its side, and after 15 minutes in the upright position. Five (5) minutes after the Auto-
Off has been activated, in any position, the iron display and all lights will turn totally OFF.
If you leave the iron:
• I n a horizontal position without moving it, or accidentally tip the iron over, it will automatically stop heating
after 30 seconds. The OFF selection on the digital display and the red Wait light blink to let you know that the
iron has stopped heating.
• I n a vertical position (on its heel rest) without moving it, the iron will automatically turn off after 15 minutes.
The OFF selection on the digital display and the red Wait light blink to let you know that the iron has stopped
heating.
Important: The OFF selection on the digital display and the red Wait light will continue to blink for 5 minutes, then
turn totally OFF.
To reset the iron:
• M ove the iron back and forth. The OFF selection on the digital display and the red Wait light will stop
blinking and the iron will start heating again (allow it to reheat for 2 minutes); the desired fabric setting will be
highlighted.
• P ress the ( - + ) Fabric Select button, the digital display and red Wait light will illuminate, indicating power has
been restored to the iron (the desired fabric setting will still be selected). Wait for the light to turn GREEN before
ironing.
™
WARNING: The MOTION SMART Auto-Off is a safety feature, not a recommended means for turning your iron
off. See "Caring for Your Iron After Use" for information on turning off your iron and storing it safely between use.
I ' s f
Ron s pecIal eatuRes
:
®
button each time you would like an extra burst of
f
eatuRe
1. Unplug the iron from the power source.
WARNING: NEVER yank the power cord when unplug
s Y I
toRIng ouR Ron
1. Allow the iron to cool. (Model 4265-33 only: Wait
original black color, indicating that the iron is cool en
2. I f you do not use your iron on a daily basis, empty th
do so, unplug the iron, turn the iron upside down, o
hole. Shake the iron gently to remove trapped water
3. L oosely loop the power cord around the heel rest an
Important: Wrapping the cord around the iron too tightly
Tip: When not ironing, always set the Steam Selection Slid
m
aIntaInIng
c s
leanIng the oleplate
Clean the soleplate if starch or other residue accumulate.
t s :
o clean the oleplate
1. Unplug the iron. Allow the iron to cool and then wip
WARNING: DO NOT use abrasive cleansers, scouring pad
2. Run the iron over an all-cotton cloth to remove any
u s -c f
sIng the elf leanIng eatuRe
You should use the Self-Cleaning feature once a month to
t s -c :
o use the elf leanIng featuRe
1. U nplug the iron. Move the Steam Selection Slide bac
from the Steam Valve. This keeps water flowing into
2. Fill the water reservoir with tap water to the MAX l
3. P lug in the iron and press Fabric Select button to Linen
4. Unplug the iron.
5. Hold the iron over a sink in a horizontal position.
WARNING: Be careful not to touch the iron's hot surfac
6. P ress the Self-Clean button and hold. Water will beg
to side and front to back for 30 seconds. When rock
of the iron to make certain the water circulates comp
7. T urn the iron upside down and allow the remaining
8. Dry the soleplate with a towel.
9. P lug in the iron and press the Fabric Select button to
and dry out the iron completely.
10. P ress the Fabric Select button to OFF. The lights will
Unplug the iron and allow it to cool.
c a -c s
leanIng the ntI alcIum Ystem
The professional iron houses an anti-calcium filter in the r
t
o pRolong the effIcIencY of thIs fIlteR
1. Unplug the iron and allow it to cool.
2. L ocate the water cup that accompanied the iron and
fill the water reservoir with this solution.
3. Leave the solution in the water reservoir for 15 minu
4. F ill the water reservoir a second time with the salt w
5. Fill the tank with fresh water to rinse and empty.
The Anti-Calcium System should be cleaned approximate
Y
ouR
: