Bosch GAS 35 L SFC+ Original Instructions Manual page 19

OBJ_BUCH-1702-003.book Page 19 Monday, September 29, 2014 2:58 PM
Technical Data
Wet/dry vacuum cleaner
Article number
Rated power input
Frequency
Container volume (gross)
Net volume (for fluids)
Dust bag contents
Max. vacuum*
– Vacuum cleaner
– Turbine
Max. flow rate*
– Vacuum cleaner
– Turbine
Max. vacuum capacity
Surface of flat-fold filter
Dust category
Weight according to
EPTA-Procedure 01/2003
Protection class
Degree of protection
* Measured with a Ø 35 mm and 3 m long vacuum hose
The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
Automatic Start/Stop feature*
Rated voltage max. power output min. power output
EU 220–240 V 2200 W
UK 110 V
UK 240 V 1800 W
CH 230 V 1100 W
* Specification of the allowable load of the connected power tool (coun-
try-specific)
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60335-1, EN 60335-2-69.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 30.09.2014
Bosch Power Tools
Assembly
GAS 35 L SFC+
 Before any work on the vacuum cleaner itself, pull the
3 601 JC3 0..
W 1200
Mounting the Vacuum-hose Holder (see figure A)
Hz 50/60
– Slide the vacuum-hose holders 4 firmly from above into the
l 35
l 19
Mounting the Vacuum Hose (see figure B)
l 19
– Mount the vacuum hose 21 onto the hose connection
hPa 230
hPa 254
Note: While vacuuming, an electrostatic charge develops in
the vacuum hose and accessories caused by the friction of the
dust, which the operator could experience in the form of stat-
l/s 36
ic discharging (dependent on environmental influences and
3
m /s 0.036
physical perception).
l/s 74
As a general rule, Bosch recommends using an anti-static vac-
3
m /s 0.074
uum hose (accessory) when vacuuming fine dusts and dry
W 1380 materials.
2
m 0.615
Mounting VAC Accessories
L
The vacuum hose 21 and the SFC+ module 20 are equipped
with a clip system, with which the VAC accessories (tool
kg 12.2
sleeve 19, elbow 22) can be connected.
/I
Mounting the Tool Sleeve (see figure C)
IP X4
– Mount the SFC+ module 20 onto the vacuum hose 21 until
– Afterwards, mount the tool sleeve 19 onto the SFC+ mod-
– To disassemble, press both snap-fasteners 31 inward and
100 W
750 W 100 W
Mounting Nozzles and Tubes (see figure D)
100 W
– Mount the elbow 22 onto the vacuum hose 21 until both
100 W
– Afterwards, mount the desired VAC accessory (floor noz-
– To disassemble, press both snap-fasteners 31 inward and
Inserting/Removing a Disposal Bag or Dust
Bag (Dry Vacuuming) (see figures E1 – E2)
For dry vacuuming, a disposal bag 23 or a dust bag (accesso-
ry) can be used. This makes the disposal of the dust easier.
Note: When using a paper filter bag, the semi-automatic filter
cleaning (SFC+) (see "Deactivating the SFC+", page 21),
must, and when using a fleece filter bag, should be shut off.
mains plug.
retainers 30 intended for this purpose, until they engage.
piece 2 and turn it in clockwise direction to the stop.
both snap-fasteners 31 of the vacuum hose can be heard
to engage.
ule 20 until both snap-fasteners 31 of the SFC+ module
can be heard to engage.
pull the components apart.
snap-fasteners 31 of the vacuum hose can be heard to en-
gage.
zle, crevice nozzle, vacuum tube, etc.) firmly onto the el-
bow 22.
pull the components apart.
English | 19
1 609 92A 0XC | (29.9.14)