Appendix B: Specifications; General Spec - Yamaha DM 2000 Owner's Manual

Appendix B: Specifications

General Spec

Number of scene memories
Sampling Frequency
Signal Delay
Fader
Fader Resolution
1
Total Harmonic Distortion
(CH INPUT to STEREO OUT)
(Input Gain=Min.)
Frequency Response
(CH INPUT to STEREO OUT)
Dynamic Range
(maximum level to noise level)
2
Hum & Noise
(20 Hz–20 kHz)
Rs=150 Ω
Input Gain=Max.
Input Pad =0 dB
Maximum Voltage Gain
Crosstalk
(@ 1 kHz)
Input Gain=Min.
AD Input (1–24: A/B)
Analog Input
(2TR IN ANALOG 1, 2)
Option Input (SLOT 1–6)
Digital Input
(2TR IN DIGITAL 1–3)
99
Internal
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
Normal rate: 44.1 kHz–10% to 48 kHz+6%
External
Double rate: 88.2 kHz–10% to 96 kHz+6%
Less than 2.3 ms CH INPUT to STEREO OUT (fs=48 kHz)
Less than 1.2 ms CH INPUT to STEREO OUT (fs=96 kHz)
100 mm motorized with touch sense × 25
+10 to –96, –∞ dB (256 steps/100 mm) input faders
0 to –130, –∞ dB (256 steps/100 mm) master faders, stereo fader
Less than 0.05% 20 Hz to 20 kHz @ +14 dB into 600 Ω
fs=48 kHz
Less than 0.01% 1 kHz @ +18 dB into 600 Ω
Less than 0.05% 20 Hz to 40 kHz @ +14 dB into 600 Ω
fs=96 kHz
Less than 0.01% 1 kHz @ +18 dB into 600 Ω
20 Hz–20 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω (fs=48 kHz)
20 Hz–40 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω (fs=96 kHz)
110 dB typ. DA Converter (STEREO OUT)
108 dB typ. AD+DA (to STEREO OUT) @ fs=48 kHz
106 dB typ. AD+DA (to STEREO OUT) @ fs=96 kHz
–128 dB Equivalent Input Noise
–92 dB residual output noise. STEREO OUT (STEREO OUT off)
–92 dB (96 dB S/N) STEREO OUT (STEREO fader at nominal level and
all CH INPUT faders at minimum level)
–64 dB (68 dB S/N) STEREO OUTPUT (STEREO fader at nominal level
and one CH INPUT fader at nominal level)
74 dB CH INPUT (CH1–24) to STEREO OUT/OMNI (BUS) OUT
74 dB CH INPUT (CH1–24) to OMNI (AUX) OUT (via pre input fader)
74 dB CH INPUT (CH1–24) to CONTROL ROOM MONITOR OUT (via
STEREO bus)
–80 dB adjacent input channels (CH1–24)
–80 dB input to output
Phantom switch
+48 V DC is supplied to A (XLR-3-31 type) input
Pad switch
0/26 dB attenuation
Gain control
44 dB (–60 to –16), detented
Peak indicator
LED (red) turns on when post HA level reaches 3 dB below clipping
LED (green) turns on when post HA level reaches 20 dB below nomi-
Signal indicator
nal
Insert
OUT, IN (pre AD converter)
Insert switch
on/off
AD converter
24-bit linear, 128-times oversampling (fs=48 kHz)
AD converter
24-bit linear, 128-times oversampling (fs=48 kHz)
Available cards
Optional digital interface cards (MY8, MY4 series)
SRC
On/off (1:3 and 3:1 maximum input to output sample rate ratio)
301
General Spec
DM2000—Owner's Manual