Weider 8507 User Manual page 11

26. Press a 1 1/2" Square Inner Cap (32) into the Leg
Lever (29).
Attach the 5/16" x 2" Eyebolt (62) to the Leg Lever
(29) with a 5/16" Flat Washer (8) and a 5/16" Nylon
Locknut (3).
Lubricate a 5/16" x 2 1/4" Bolt (33). Attach the Leg
Lever (29) to the Seat Frame (36) with the Bolt and
a 5/16" Nylon Locknut (3). Do not overtighten the
Nylon Locknut; the Leg Lever must be able to
pivot freely.
27. Set the bracket on the Seat Frame (36) onto the
indicated pin on the Front Upright (42). Attach the
Seat Frame with a 5/16" x 2 3/4" Carriage Bolt (14)
and the Seat Knob (40).
28. Press 3/4" Round Inner Caps (34) into the ends of
a Pad Tube (28). Insert the Pad Tube into the Seat
Frame (36). Slide a Pad (30) onto each end of the
Pad Tube.
Press 3/4" Round Inner Caps (34) into the ends of
the other Pad Tube (28). Insert the Pad Tube into
the Leg Lever (29). Slide a Pad (30) onto each end
of the Pad Tube.
26
3
36
33
29
8
62
3
32
27
36
40
14
Pin
42
28
36
30
28
30
34
29
14
19. Note: The 3 1/2" Pulley (15) shown in this step
is pre-attached to the Adjustment "U" Bracket
(75).
Remove the 3/8" x 1 3/4" Bolt (48), 3/8" Nylon Jam
Nut (5), two Pulley Covers (89), and the 3 1/2"
Pulley (15) from the Adjustment "U" Bracket (75).
Attach the Adjustment "U" Bracket (75) to the Front
Upright (42) with the 5/16" x 3 1/4" Bolt (35), a 5/16"
Flat Washer (8), and a 5/16" Nylon Locknut (3).
Thread the Nylon Locknut onto the Bolt until the
first two threads of the Bolt are through the
Nylon Locknut.
Wrap the Long Cable (66) around the 3 1/2" Pulley
(15) as shown. Re-attach the Pulley and the Pulley
Covers (89) to the Adjustment "U" Bracket (75) with
the 3/8" x 1 3/4" Bolt (48) and 3/8" Nylon Jam Nut
(5). The Pulley Covers must be oriented as
shown.
20. Note: The 3 1/2" Pulley (15) used in this step is
pre-assembled.
Remove the 3/8" x 1 3/4" Bolt (48), the 3/8" Nylon
Jam Nut (5), the two Pulley Covers (89), and the
3.1/2" Pulley (15) from the Swivel Bracket (58) on
the right Arm (46).
Wrap the Long Cable (66) around the 3 1/2" Pulley
(15). Re-attach the Pulley and the two Pulley
Covers (89) to the Swivel Bracket (58) with the 3/8"
Nylon Jam Nut (5) and 3/8" x 1 3/4" Bolt (48). Be
sure that the Pulley Covers are oriented as
shown.
34
19
48
89
35
The Narrow
3
Tabs must
8
be on this
15
side
5 66
75
89
42
20
48
66
89
58
15
5
46
The Wide
Tabs must
be on this
side
11