Ryobi EMS-1121L User Manual page 18

GB
F D
ASSEMBLY
WARNING!
The correct selection of the saw blade depends
on the type and quality of the wood and whether
lengthways or crossways cutting is required.
WARNING!
Beech and oak dusts are especially detrimental
to health and therefore maybe worked only with
dust collector.
INSTALLING THE BLADE (Fig. 7-9)
Unplug the Mitre Saw.
■
Press down the handle (1) then pull out the lock pin to
■
release handle.
Remove the front end blade bolt cover screw (21).
■
Raise the lower blade guard to its highest position
■
(Note: Be careful, the lower guard is spring loaded).
Use the provided spanner (13) to hold the flange and
■
then use the provided wrench (14) to unscrew the
arbor bolt (22).
Remove the blade flange and place the blade (16) into
■
the arbor. Ensure the blade is correctly positioned, with
its teeth pointing downwards at the front of the saw
Reassemble the blade flange to the arbor and closely
■
fit with the blade.
Tighten up the arbor bolt in an anti-clockwise direction.
■
Use the spanner to hold the flange and use wrench to
■
tighten the arbor bolt.
Use thumb to press the safety interlock to allow the
■
movement of the blade guard back to cover the blade.
Tighten the screws on the blade bolt cover.
■
Check to ensure the safety lock is already at the
■
upper end of the lower guard and prevent any
movement of the lower blade guard by slightly moving
the lower blade guard downward.
INSTALLING THE DUST BAG (11)
The dust bag is installed by squeezing the two metal clips
to open the mouth of the bag and sliding it on the dust
post. The metal ring should lock in between the grooves
on the port (Fig. 10).
E I P NL S DK N FIN
English
ADJUSTMENTS
REPLACE THE BLADE (Fig.11)
Unplug the Mitre Saw.
■
Remove the front end blade bolt cover screw.
■
Raise the saw to its highest position (Note: Be careful,
■
the lower guard is spring loaded)
Use the wrench to hold the flange and then use the
■
spanner to unscrew the arbor bolt.
Remove the blade and replace the existing blade with
■
a new one.
Reassemble the blade flange.
■
Use the spanner to hold the flange and use wrench to
■
tighten the arbor bolt.
Move the lower blade guard back to cover the blade
■
and tighten the screws on the blade bolt cover.
Check to ensure the safety lock is already at the
■
upper end of the lower guard and prevent any
movement of the lower blade guard by slightly moving
the lower blade guard downward.
SQUARING THE BLADE TO THE FENCE
Pull the handle all the way down and engage the lock
■
down pin to hold the handle in the transport position.
(fig. 4 & 6).
Rotate mitre locks lever up to release the table.
■
Rotate the mitre table (5) until the pointer is
positioned at 0º. Return mitre lock lever to its lock
position (fig. 5)
Place a set square on the mitre table against the rear
■
fence and blade (fig. 12). Adjustment is needed if they
are not perpendicular.
If adjustment is needed, loosen Allen screw (23) at
■
the rear of the table (fig. 14).
Using the set square correctly align the fence and the
■
blade then retighten all Allen screws. (fig. 12 & 17). .
SQUARING THE BLADE TO THE MITRE TABLE
Pull the handle all the way down and engage the lock
■
down pin to hold the handle in the transport position.
(fig. 15)
Unlock the bevel lock knob (20) and move the handle
■
to the 0° position and lock the bevel lock knob. (fig. 14)
Place a set square on the mitre table against the rear
■
fence and blade. Adjustment is needed if they are not
perpendicular (fig. 15).
Unscrew the 0° bevel positioning screw at the rear
■
(fig. 16).
12
GR H CZ RUS RO PL