Ryobi EMS-1121L User Manual page 16

GB
F D
ADDITIONAL SAFETY RULES
Do not use the saw to cut metal or masonry.
■
Do not let anyone under 18 years old operate this saw.
■
Ensure that the operator is adequately trained in the
■
use, adjustment and operation of the machine.
Do not use this saw to cut firewood.
■
Keep the area free of tripping hazards.
■
Report faults in the machine, including guards and
■
saw blades, as soon as they are discovered.
Ensure that the machine is always fixed to a bench,
■
whenever possible.
Always stand to one side when operating the saw.
■
Never use a cracked or distorted saw blade. Only use
■
sharp blades.
When cutting round wood, use clamps that prevent
■
the work piece from turning on both sides of the blade.
Never use your hands to remove sawdust, chips or
■
waste close by the blade.
Use only blades as recommended by the
■
manufacturer and which conform to EN 847-1.
Do not use blades of High Speed Steel (HSS blades).
■
If the table insert is damaged or worn, have it
replaced by an authorised service centre.
Rags, cloths, cord and string and the like should
■
never be left around the work area.
Avoid cutting nails. Inspect the work piece and
■
remove all nails and other foreign objects before
beginning sawing.
Support the work properly.
■
Refrain from removing any cut-offs or other parts of
■
the work piece from the cutting area whilst the
machine is running and the saw head is not in the
rest position.
Do not attempt to free a jammed blade before first
■
switching off the tool.
Do not slow or stop a blade with a piece of wood.
■
Let the blade come to rest naturally
If you are interrupted when operating the saw,
■
complete the process and switch off before looking up.
Periodically check that all nuts, bolts and other fixings
■
are properly tightened.
Do not store materials or equipment above a machine
■
in such a way that they could fall into it.
Always hold the saw on parts that are insulated.
■
If you accidentally cut into hidden wiring or the saw's
own cable, the metal parts of the saw will become
"live". Switch off at the mains and remove the plug
immediately.
E I P NL S DK N FIN
English
Never saw near combustible liquids or gases.
■
Note the direction of rotation of the motor and the blade.
■
Do not lock the movable guard in the open position and
■
always ensure that it is working properly, freely rotating
and returning to fully cover the teeth of the blade.
Connect the saw to a dust collection device and
■
ensure that it is operated properly. As the operator of
the saw, please make sure that you understand
factors that influence exposure to dust, including the
type of material to be machined, the importance of
local extraction and the proper adjustment of
hoods/baffles/shoots of your dust extraction system.
We recommend that you always wear a dust mask
when operating this saw.
Wear gloves when handling saw blades and rough
■
materials.
Saw blades shall be carried in a holder wherever
■
possible.
Select saw blades in relation to the material being cut.
■
Use correctly sharpened saw blades and observe the
■
maximum speed marked on the blade.
Keep the floor area around the machine level, well
■
maintained and free of loose materials such as wood
chips and cut-offs.
Always use stands to provide support for long work
■
pieces that overhang the turntable.
The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual will
be considered a case of misuse. The user and not the
manufacturer shall be liable for any damage or injury
resulting from such cases of misuse. The manufacturer
shall not be liable for any changes made to the tool nor
for any damage resulting from such changes. Even when
the tool is used as prescribed it is not possible to
eliminate all residual risk factors.
LASER BEAM SAFETY INSTRUCTIONS
Do not look into the laser beam.
■
Do not point the laser beam at people or animals.
■
Do not use the laser beam on highly reflective
■
materials. Reflected light is dangerous.
Have the laser beam repaired only by specialists.
■
Do not touch the Laser lens with hard objects.
■
Clean the laser lens with a soft, dry brush.
■
10
GR H CZ RUS RO PL