Page 2
PCM-D50 General Linear PCM Quantization: 16-bit linear, 24-bit Power requirements linear DC IN 6V Frequency range (Input from the LINE Four LR6 (size AA) alkaline batteries IN (OPT) jack when recording/ (supplied) playing back) (0 to –2 dB): Four nickel metal hydride Fs 22.05 kHz: 20 to 10,000 Hz...
Page 3
THESE COMPONENTS WITH SONY PARTS PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON- WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. PUBLIÉS PAR SONY.
PCM-D50 SECTION 1 This section is extracted GENERAL from instruction manual. Identifying parts and controls Front Right side...
Page 6
PCM-D50 Built-in microphones (page 21) DIVIDE button (page 35) Peak level lamps (L/R) (page 24) PLAY/ENTER button/indicator Displays left and right peak levels of an (pages 31) audio signal input with -12dB (green) and STOP button (pages 25, 32) OVER (red) lamps.
Page 7
PCM-D50 Identifying parts and controls (continued) Left side LIMITER switch (pages 22, 43) LOW CUT FILTER switch (pages 22, 43) Hole for attaching the tripod (not supplied) INPUT switch (pages 23, 28, 29, 30) When set to “ ” (microphone), records an...
Page 8
PCM-D50 Display Time information Each time the DISPLAY button is pressed, the time information changes as follows (Flashes when the recorder is paused): Elapsed recording/playback time Remaining recordable time of the current memory (During playback: Remaining time of the current track)
Page 9
PCM-D50 Identifying parts and controls (continued) Memory Stick indicator Displayed when the current memory is a “Memory Stick.” Folder number, track numbers Folders are classified into (a folder for recording and playback) and (a folder for playback only) (page 38). Track numbers are displayed as “current track number/total...
PCM-D50 SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. PANEL (FRONT) ASSY (Page 11) 2-2. ORNAMENTAL BELT (UPPER) ASSY (Page 11) 2-3. BACKLIGHT BOARD 2-4. POWER BOARD (Page 12) (Page 12) 2-5. REC VOL ASSY,...
PCM-D50 Note: Follow the disassembly procedure in the numerical order shown below. 2-1. PANEL (FRONT) ASSY two screws (M 1.7) two cushions (panel) panel (front) assy two cushions (panel) two screws (M 1.7) 2-2. ORNAMENTAL BELT (UPPER) ASSY screw guard (MC) (M 1.4)
PCM-D50 2-3. BACKLIGHT BOARD two claws LCD assy BACKLIGHT board LCD unit (13 core) (CN4201) two screws P2 lock ace (M 1.7) Remove the two solders. white LCD assy two screws P2 lock ace (M 1.7) 2-4. POWER BOARD Remove the four solders.
PCM-D50 2-5. REC VOL ASSY, HP VOL ASSY Remove the six solders. white orange knob (VOL) yellow gray black HP VOL assy two screws precision pan (M 1.4) (EG) REC VOL assy CN3001 guard (VOL) screw 2-6. DA BOARD chassis (PWB)
PCM-D50 2-7. AD BOARD, MIC001, MIC002 MIC001 MIC002 Remove the six solders. MIC001 MIC002 black yellow yellow black two screws P2 lock ace (M 1.7) S3002 S3003 AD board screw (M2 grip) ground plate Remove the two solders. screw (M 1.7) 2-8.
PCM-D50 SECTION 3 TEST MODE This set provides the Test Mode that can be used for the following 5. Flow Chart of the TEST MODE check modes. START 1. Setting and Exiting the TEST MODE After power-on, • Types of TEST MODE and setting the TEST MODE...
Page 16
1 Version HPMUTE : OFF LINEMUTE : OFF Function: To check the version of the relevant module. LIMITER : OFF LCF : OFF PCM-D50 : JP Boot : 11 ARM 1. 0. 00 [PLAY]: Starts Loop Back DSP 1. 0. 00...
Page 17
PCM-D50 LCD Contrast Adjustment 9 DCIN When the system board or LCD1 has been replaced, the LCD con- Function: To display the current value of DCIN A/D and trast should be adjusted. whether it can be detected by the 5T735 detection 1.
PCM-D50 SECTION 4 DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. Note: Note: • X : Parts extracted from the component side.
Page 19
PCM-D50 • CIRCUITS BOARDS LOCATION • Waveforms – SYSTEM Board – IC1001 (OSCOUT) AD board (X1401) SYSTEM board 1.3 Vp-p DA board 32.768 kHz 0.5 V/DIV, 20 μsec/DIV BACKLIGHT board IC1001 (CKI) (X1101) 2 Vp-p 12 MHz POWER board 0.5 V/DIV, 50 nsec/DIV...
PCM-D50 4-7. SCHEMATIC DIAGRAM – AD Section (2/3) – • See page 46 for IC Block Diagrams. AD BOARD (2/3) OPTIN BOARD (1/3) (Page 25) IC B/D IC3405 IC B/D CLOCK SELECT IC B/D IC3405 IC3401 TC7PA53FU(TE85L.F) CLOCK GENERATOR IC3401...
PCM-D50 4-12. SCHEMATIC DIAGRAM – DA Section – • See page 45 for IC Block Diagrams. DA BOARD OPTOUT R4089 R4031 R4036 IC B/D IC4007 IC B/D Q4032 IC4007 IC B/D C4065 EM6M1T2R TC7SB66FU(TE85R) MUTE DRIVE IC4004 0.1u R4069 R4092...
PCM-D50 When IC1503 on the System board are damaged, exchange the new System board for the System board which IC damaged. 4-13. PRINTED WIRING BOARD – SYSTEM Section (1/2) – • See page 19 for Circuit Boards Location. • : Uses unleaded solder.
PCM-D50 When IC1001, IC1201 and IC1301 on the System board are damaged, exchange 4-14. PRINTED WIRING BOARD – SYSTEM Section (2/2) – • See page 19 for Circuit Boards Location. • : Uses unleaded solder. the new System board for the System board which IC damaged.
PCM-D50 When IC1001 on the System board are damaged, exchange the 4-15. SCHEMATIC DIAGRAM – SYSTEM Section (1/5) – • See page 19 for waveforms. • See page 53 for IC Pin Function Description of IC1001. new System board for the System board which IC damaged.
PCM-D50 When IC1201 and IC1301 on the System board are damaged, exchange 4-16. SCHEMATIC DIAGRAM – SYSTEM Section (2/5) – the new System board for the System board which IC damaged. SYSTEM BOARD (2/5) SYSTEM VDD_SDR BOARD VDD_SDR (1/5) C1201...
PCM-D50 When IC1503 on the System board are damaged, exchange the 4-18. SCHEMATIC DIAGRAM – SYSTEM Section (4/5) – • See page 50 for IC Block Diagrams. • See page 61 for IC Pin Function Description of IC1503. new System board for the System board which IC damaged.
PCM-D50 When IC2301 on the Power board are damaged, exchange the 4-20. PRINTED WIRING BOARD – POWER Section (1/2) – • See page 19 for Circuit Boards Location. • : Uses unleaded solder. new Power board for the Power board which IC damaged.
PCM-D50 When IC2301 on the Power board are damaged, exchange the new Power board for the Power board which IC damaged. 4-25. SCHEMATIC DIAGRAM – POWER Section (4/4) – • See page 50 for IC Block Diagram. • See page 63 for IC Pin Function Description of IC2301.
Page 45
PCM-D50 • IC Block Diagrams IC3001 ADA4841-2YRZ-R7 (AD Board (1/3)) IC3002 AD8662ARZ-REEL (AD Board (1/3)) IC3003 AD8662ARZ-REEL (AD Board (1/3)) IC3004 AD8662ARZ-REEL (AD Board (1/3)) IC4002 AD8662ARZ-REEL (DA Board) IC4004 AD8662ARZ-REEL (DA Board) OUTA –INA OUTB +INA –INB V– +INB...
Page 46
PCM-D50 IC3401 NJU6366AF1(TE1) (AD Board (2/3)) 3-STATE BUFFER IC3403 NJU6311RB2(TE1) (AD Board (2/3)) 3-STATE OUTPUT SELECTOR BUFFER...
Page 53
PCM-D50 • IC Pin Function Description SYSTEM BOARD (1/5) IC1001 MC-10051F1-FAE-A (SYSTEM CONTROL/DSP) Pin No. Pin Name Description A1, A2, A3 — Not used (Open) NAND_WEZ Write enable signal output to the NAND ROM IO_B — Power supply (VDD_GP1) PBIAS —...
Page 54
PCM-D50 Pin No. Pin Name Description SWADP — Not used (Open) CAPVBDL — Not used (Open) VCCVBAT1 — Power supply (battery) USBTEST3 — Not used (Open) IO_A — Power supply (VDD_GP1) AB0_A5 Address signal output to the USB I/F C21, C22 AB0_A10, AB0_A15 —...
Page 55
PCM-D50 Pin No. Pin Name Description ISENS — Not used (Open) DGND — Ground DISCHGVBUS — Not used (Pull Down) SESSV — Not used (Open) IDGD — Not used (Open) IO_B — Power supply (VDD_GP1) AB0_CSZ2 Chip select signal output (Not used in this set)
Page 56
PCM-D50 Pin No. Pin Name Description LCD_ENABLE — Not used (Open) LCD_VSYNC — Not used (Open) CHGGND2 — Ground — Not used (Open) SDR_DATA23 LED drive signal output SDR_DATA22 LED drive signal output SDR_DATA21 LED drive signal output SDR_DATA20 —...
Page 57
PCM-D50 Pin No. Pin Name Description — Ground R22, R23 LCD_R2, LCD_R4_ — Not used (Open) GNDSINK — Ground VDD_L0 — Power supply (VDD_L0) VUSB — Not used (Open) SDR_CKE0 Clock enable signal output to SD-RAM SDR_CSZ1 Chip select signal output (Not used in this set) (Open)
Page 58
PCM-D50 Pin No. Pin Name Description W4, W5 SDR_A4, SDR_A3 Address signal output to SD-RAM SPI1_SO Serial data output to the digital audio I/F transceiver — Ground SPI1_CSZ0 Chip select signal output to the digital audio I/F transceiver W11 to W18 —...
Page 59
PCM-D50 Pin No. Pin Name Description IO_C — Power supply (VDD_GP1) AC10 CAM_YUV6 PWM signal output to the DC/DC converter AC11 CAM_YUV2 Power supply control signal output AC12 CAM_VS LINE OUT (OPT) transmitter power control signal output AC13 ISENSE —...
Page 60
PCM-D50 Pin No. Pin Name Description AE14 AVDD_LPLL — Power supply (VDD_PLL) AE15 AVDD_HPLL — Power supply (VDD_PLL) AE16 — Ground AE17 DD1VFBK VDD_L1 power supply voltage feedback input AE18 VDD_DSP — Power supply (VDD_L1) AE19 IO_A — Power supply (VDD_IOA)
Page 61
PCM-D50 SYSTEM BOARD (4/5) IC1503 M66592UG (USB I/F) Pin No. Pin Name Description AFED33G — Ground RST_N Reset signal input DACK1_N/DSTB0_N — Not used (Connected to VIF) DEND0_N — Not used (Open) CS_N Chip select signal input RD_N Read enable signal input...
Page 62
PCM-D50 Pin No. Pin Name Description MPBUS Bus mode signal input Address signal input Address signal input Date input/output D3/AD3 Date input/output D5/AD5 Date input/output Date input/output Date input/output...
Page 63
PCM-D50 POWER BOARD (4/4) IC2301 UPD78F0501AMC-5A4-E2-A (SIRCS CONTROL) Pin No. Pin Name Description ANI1/P21 Sircs key signal output ANI0/P20 Sircs key signal output P01/TI010/TO00 Sircs key signal output P00/TI000 Sircs key signal output P120/INTP0/EXLVI Sircs signal input nRESET System reset signal input...
PCM-D50 SECTION 5 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • The mechanical parts with no reference The components identifi ed by mark 0 they may have some difference from the number in the exploded views are not sup- or dotted line with mark 0 are critical for original one.
PCM-D50 SECTION 6 ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • RESISTORS When indicating parts by reference num- the parts list may be different from the All resistors are in ohms. ber, please include the board name.
PCM-D50 REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2007.10...